journal article·2025-01Open access

Sb2S3 solar cells with TiO2 electron transporting layers synthesized by ALD and USP methods

T. Dedova, R. Krautmann, M. Rusu, A. Katerski, M. Krunks, T. Unold, N. Spalatu, A. Mere, J. Sydorenko, M. Sibiński, I. Oja Acik

Abstract

Electronic characteristics were investigated for solar cells (SCs) based on FTO/TiO 2 /Sb 2 S 3 /P3HT/Au structure, employing TiO 2 electron transport layers (ETLs) fabricated by two different methods: ultrasonic spray pyrolysis (USP) and atomic layer deposition (ALD). Regardless of the deposition method, both ALD and USP-TiO 2 exhibit the anatase crystal structure. The calculated crystallite sizes, derived from the (101) reflection of TiO 2 layers using the Scherrer equation, show minimal variance between the two methods, with values 25 nm for USP and 30 nm for ALD TiO 2 , respectively. Optical band gaps (E g ) were found to be 3.31 eV and 3.35 eV for USP and ALD methods, respectively. Exploring the thickness series of ALD-TiO 2 , ranging from 100 to 1000 cycles (approximately 5–75 nm), solar cell performance was evaluated, with the highest power conversion efficiency (PCE) of 3.3 % achieved using ALD-TiO 2 of 400 cycles (approximately 30 nm thick). Notably, SCs featuring USP TiO 2 ETL layers, with a thickness of approximately 35–40 nm, outperform their ALD-TiO 2 counterparts, improving PCE by 15 %, recording 4.0 % versus 3.3 %, respectively. This superiority in PCE is attributed to the more favorable conduction band minimum (CBM) position of USP-TiO 2 relative to the Fermi level, as revealed in the band diagram. Specifically, a lower CBM spike at the USP-TiO 2 /-Sb 2 S 3 interface indicates reduced recombination rates compared to those at the ALD-TiO 2 /-Sb 2 S 3 interface. This study offers valuable insights into enhancing SC performance by optimizing deposition methods and synthesis parameters of ETL layers. • Sb 2 S 3 solar cells with TiO 2 electron transporting layers synthesized by ALD and USP methods are studied. • 15 % boost in performance of SC based on USP-TiO 2 ETL layers. • The lower CBM spike at the USP-TiO 2 /Sb 2 S 3 interface indicates a reduced recombination rate. • USP-TiO 2 is cost-effective and high-quality ETL for thin film Sb 2 S 3 solar cells.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · Quantum Dots Synthesis And Properties · Advanced Semiconductor Detectors and Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (67)

Show source-provided references
1. Synergistic effect through the introduction of inorganic zinc halides at the interface of TiO 2 and Sb 2 S 3 for high-performance Sb 2 S 3 planar thin-film solar cells10.1021/acsami.0c11550 ↗
2. 4.9% efficient Sb 2 S 3 solar cells from semitransparent absorbers with fluorene-based thiophene-terminated hole conductors10.1021/acsaem.2c04097 ↗
3. Semitransparent Sb 2 S 3 thin film solar cells by ultrasonic spray pyrolysis for use in solar windows10.3762/bjnano.10.230 ↗
4. Vacuum assisted solution processing for highly efficient Sb 2 S 3 solar cells10.1039/C8TA05614E ↗
5. Quasiepitaxy strategy for efficient full‐inorganic Sb 2 S 3 solar cells10.1002/adfm.201901720 ↗
6. Sb 2 S 3 solar cells with a cost-effective and dopant-free fluorene-based enamine as a hole transport material10.1039/D2SE00356B ↗
7. Wide bandgap Sb 2 S 3 solar cells10.1002/adfm.202100265 ↗
8. 9.2%-efficient core-shell structured antimony selenide nanorod array solar cells10.1038/s41467-018-07903-6 ↗
9. Stable 6%-efficient Sb2Se3 solar cells with a ZnO buffer layer10.1038/nenergy.2017.46 ↗
10. Sb 2 Se 3 thin‐film solar cells exceeding 10% power conversion efficiency enabled by injection vapor deposition Technology10.1002/adma.202202969 ↗
11. 6.5% certified efficiency Sb 2 Se 3 solar cells using PbS colloidal quantum dot film as hole-transporting layer10.1021/acsenergylett.7b00648 ↗
12. Regulating energy band alignment via alkaline metal fluoride assisted solution post‐treatment enabling Sb 2 (S,Se) 3 solar cells with 10.7% efficiency
13. Bifacial and semitransparent Sb 2 (S,Se) 3 solar cells for single‐junction and tandem photovoltaic applications10.1002/adma.202303936 ↗
14. Hydrothermal deposition of antimony selenosulfide thin films enables solar cells with 10% efficiency10.1038/s41560-020-0652-3 ↗
15. Efficient CdS buffered TiO2 electronic transport layer for Sb2S3 solar cells by a facile spinning coating process10.1007/s00339-022-05627-5 ↗
16. A novel approach for the synthesis of tin antimony sulphide thin films for photovoltaic application10.1016/j.solener.2014.12.021 ↗
17. Enhanced performance of the Sb 2 Se 3 thin-film solar cell by organic molecule-induced crystallization and suppression of the interface recombination10.1021/acsaem.1c00640 ↗
18. High efficiency perovskite solar cells using DC sputtered compact TiO 2 electron transport layer10.1051/epjpv/2021008 ↗
19. Efficiency enhancement of hole-conductor-free perovskite solar cell based on ZnO nanostructure by Al doping in ZnO10.1016/j.jallcom.2016.09.038 ↗
20. In situ growth of [hk1]‐Oriented Sb 2 S 3 for solution‐processed planar heterojunction solar cell with 6.4% efficiency10.1002/adfm.202002887 ↗
21. Multi‐phase sputtered TiO 2 ‐induced current–voltage distortion in Sb 2 Se 3 solar cells10.1002/admi.202300238 ↗
22. Interface engineering via sputtered oxygenated CdS:O window layer for highly efficient Sb 2 Se 3 thin‐film solar cells with efficiency above 710.1002/solr.201900225 ↗
23. Current enhancement via a TiO2 window layer for CSS Sb2Se3 solar cells: performance limits and high V oc10.1109/JPHOTOV.2018.2885836 ↗
24. Reduced extrinsic recombination process in anatase and rutile TiO2 epitaxial thin films for efficient electron transport layers10.1038/s41598-021-86422-9 ↗
25. Synthesis and characterization of TiO2 thin films for DSSC prototype10.1016/j.matpr.2016.04.108 ↗
26. Orientation engineering in low‐dimensional crystal‐structural materials via seed screening10.1002/adma.201903914 ↗
27. Highly improved Sb 2 S 3 sensitized‐inorganic–organic heterojunction solar cells and quantification of traps by deep‐level transient spectroscopy10.1002/adfm.201304238 ↗
28. Halide perovskite solar cells using monocrystalline TiO 2 nanorod arrays as electron transport layers: impact of nanorod morphology10.1088/1361-6528/aa75ab ↗
29. Optically uniform thin films of mesoporous TiO2 for perovskite solar cell applications10.1016/j.optmat.2018.12.044 ↗
30. New approach of modifying the anatase to rutile transition temperature in TiO 2 photocatalysts10.1039/C6RA19759K ↗
31. Review of the anatase to rutile phase transformation10.1007/s10853-010-5113-0 ↗
32. Thin film deposition methods: a critical review10.22214/ijraset.2021.36154 ↗
33. The effect of the deposition method on the structural and optical properties of ZnS thin films10.3390/coatings11091064 ↗
34. Effect of deposition method on the structural and optical properties of CH3NH3PbI3 perovskite thin films10.1016/j.optmat.2020.109836 ↗
35. In situ analysis of the crystallization process of Sb 2 S 3 thin films by Raman scattering and X-ray diffraction10.1016/j.matdes.2017.02.034 ↗
36. Optimization of a compact layer of TiO 2 via atomic-layer deposition for high-performance perovskite solar cells10.1039/C7SE00220C ↗
37. Improved perovskite solar cell performance by high growth rate spatial atomic layer deposited titanium oxide compact layer10.1109/JEDS.2020.3039189 ↗
38. The impact of ultra-thin titania interlayers on open circuit voltage and carrier lifetime in thin film solar cells10.1063/1.4944049 ↗
39. Plasma-assisted atomic layer deposition of TiO2 compact layers for flexible mesostructured perovskite solar cells10.1016/j.solener.2017.04.028 ↗
40. ZnO/TiO 2/Sb 2 S 3 core–shell nanowire heterostructure for extremely thin absorber solar cells10.1021/acs.jpcc.7b00178 ↗
41. Band alignment engineering towards high efficiency carbon‐based inorganic planar CsPbIBr 2 perovskite solar cells10.1002/cssc.201900611 ↗
42. A brief review of atomic layer deposition: from fundamentals to applications, Mater
43. Review Article: atomic layer deposition of optoelectronic materials
44. Applications of atomic layer deposition in solar cells10.1088/0957-4484/26/6/064001 ↗
45. An comprehensive review on the spray pyrolysis technique: historical context, operational factors, classifications, and product applications10.1016/j.jaap.2023.105915 ↗
46. Schroder · 1990
47. A facile method for Tauc exponent and corresponding electronic transitions determination in semiconductors directly from UV–Vis spectroscopy data10.1016/j.optmat.2022.112205 ↗
48. How to correctly determine the band gap energy of modified semiconductor photocatalysts based on UV–vis spectra10.1021/acs.jpclett.8b02892 ↗
49. Electronic structure of the CdS/Cu(in,Ga)Se 2 interface of KF- and RbF-treated samples by Kelvin probe and photoelectron yield spectroscopy10.1021/acsami.0c20976 ↗
50. 2019
51. Effect of the titanium isopropoxide:acetylacetone molar ratio on the photocatalytic activity of TiO2 thin films10.3390/molecules24234326 ↗
52. Enhanced visible and ultraviolet light-induced gas-phase photocatalytic activity of TiO2 thin films modified by increased amount of acetylacetone in precursor solution for spray pyrolysis10.3390/catal10091011 ↗
53. Structural, optical, and electrical properties of TiO2 thin films deposited by ALD: impact of the substrate, the deposited thickness and the deposition temperature10.1016/j.apsusc.2022.155214 ↗
54. Atomic-layer deposition of TiO2 thin films with a thermally stable (CpMe5)Ti(OMe)3 precursor10.1016/j.apsusc.2021.149381 ↗
55. New understanding of the difference of photocatalytic activity among anatase, rutile and brookite TiO2
56. Direct and real-time observation of hole transport dynamics in anatase TiO2 using X-ray free-electron laser10.1038/s41467-022-30336-1 ↗
57. Pankove · 2012
58. Idealizing Tauc plot for accurate bandgap determination of semiconductor with ultraviolet–visible spectroscopy: a case study for cubic boron arsenide10.1021/acs.jpclett.3c01416 ↗
59. Band edge optical absorption in intrinsic silicon: assessment of the indirect transition and disorder models10.1063/1.352864 ↗
60. Optical constants and band gap evolution with phase transition in sub-20-nm-thick TiO2 films prepared by ALD10.1186/s11671-017-2011-2 ↗
61. Why is anatase a better photocatalyst than rutile? - model studies on epitaxial TiO2 films10.1038/srep04043 ↗
62. Synthesis control of charge separation at anatase TiO2 thin films studied by transient surface photovoltage spectroscopy10.1021/acsami.2c09032 ↗
63. Band alignment engineering towards high efficiency carbon‐based inorganic planar CsPbIBr 2 perovskite solar cells10.1002/cssc.201900611 ↗
64. Optical and electrical properties of radio frequency sputtered tin oxide films doped with oxygen vacancies, F, Sb, or Mo10.1063/1.357383 ↗
65. Natural band alignments and band offsets of Sb2Se3 solar cells10.1021/acsaem.0c01477 ↗
66. Atomic-layer-deposited TiO2 and SnO2 coupled with CdS as double buffer layers for HTL-free Sb2S3 thin-film solar cells10.1016/j.solener.2022.09.044 ↗
67. Highly reproducible planar Sb2S3-sensitized solar cells based on atomic layer deposition10.1039/C4NR04148H ↗