Addressing separation and edge passivation challenges for high efficiency shingle heterojunction solar cells
Source abstract
Abstract
We are reporting the fabrication of high efficiency Silicon heterojunction shingle solar cells with very limited performance losses related to the cell separation. A clean and innovative separation process was elaborated and optimized, based on 45° rotated silicon brick and wafers fabrication, allowing the alignment of the preferential cleavage plan (110) with the solar cells bus bars. Hence, a simple but efficient mechanical crack propagation was sufficient to insure a proper shingles cell cut. The smooth resulting solar cell edges were found to be sensitive to surface passivation technologies. Aluminum oxide layers fabricated by atomic layer deposition were specifically developed so that their activation process is fully compatible with heterojunction low temperature constraints (typically less than 220°C). Interestingly, we showed that the annealing temperature alone was not sufficient to activate such layers; alternative forming gas annealing and/or light soaking treatments were thus successfully applied instead with very high passivation values measured on bare samples. Such layers were then deposited and activated on 45° wafer based cleaved heterojunction solar cells edges. Applied for example on heterojunction shingle cell configuration, we managed to recover up to 80% of the initial efficiency loss due to the separation, limiting the overall efficiency losses to less than 0.2% absolute.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies · Photovoltaic System Optimization Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Shingling technology for cell interconnection: technological aspects and process integration10.1016/j.egypro.2018.09.010 ↗
2. Device physics underlying silicon heterojunction and passivating‐contact solar cells: a topical review10.1002/pip.2959 ↗
3. Challenges for efficient integration of SHJ based solar cells in shingle module configuration
4. Giglia · 2020
5. Analysis of edge recombination for high-efficiency solar cells at low illumination densities, third World Conference on Photovoltaic Energy Conversion
6. Modeling of edge losses in Al-BSF silicon solar cells10.1109/JPHOTOV.2016.2618603 ↗
7. The SPEER solar cell–simulation study of shingled bifacial PERC-technology-based stripe cells
8. Laser-assisted separation processes for bifacial pSPEER shingle solar cells
9. Thermal laser separation of PERC and SHJ solar cells10.1109/JPHOTOV.2020.3041251 ↗
10. Impact of edge recombination in small-area solar cells with emitter windows10.1109/JPHOTOV.2015.2434597 ↗
11. Postmetallization “passivated edge technology” for separated silicon solar cells10.1109/JPHOTOV.2019.2959946 ↗
12. Post-separation processing for silicon heterojunction half solar cells with passivated edges10.1109/JPHOTOV.2021.3099732 ↗
13. Lelièvre · 2020
14. Danel · 2019
15. Optoelectrical analysis of TCO+ Silicon oxide double layers at the front and rear side of silicon heterojunction solar cells10.1016/j.solmat.2021.111493 ↗
16. Surface passivation of ITO on heterojunction solar cells with enhanced cell performance and module reliability
17. Influence of annealing and Al2O3 properties on the hydrogen-induced passivation of the Si/SiO2 interface10.1063/1.4709729 ↗
18. Silicon surface passivation by ultrathin Al2O3 films synthesized by thermal and plasma atomic layer deposition10.1002/pssr.200903334 ↗
19. Towards an industrial in-line solution for efficient post-treatment of silicon heterojunction solar cells10.1016/j.solmat.2022.111867 ↗
20. Edge recombination analysis of silicon solar cells using photoluminescence measurements10.1063/1.5123822 ↗
21. Low-temperature Al2O3 atomic layer deposition10.1021/cm0304546 ↗
22. Status and prospects of Al2O3-based surface passivation schemes for silicon solar cells10.1116/1.4728205 ↗
23. The influence of orientation and morphology on the passivation of crystalline silicon surfaces by Al2O310.1016/j.egypro.2014.08.055 ↗
24. Electrical characterization of ALD Al2O3 - HfO2 and PECVD Al2O3 passivation layers for p-type CZ-Silicon PERC solar cells
25. Reaction and growth mechanisms in Al2O3 deposited via atomic layer deposition: elucidating the hydrogen source10.1021/acs.chemmater.7b02759 ↗
26. Efficiency improvement of PERC solar cell using an aluminum oxide passivation layer prepared via spatial atomic layer deposition and post-annealing10.1016/j.surfcoat.2018.12.016 ↗
27. Controlling the fixed charge and passivation properties of Si (100)/Al2O3 interfaces using ultrathin SiO2 interlayers synthesized by atomic layer deposition10.1063/1.3658246 ↗
28. Detection of stable positive fixed charges in AlOx activated during annealing with in situ modulated PhotoLuminescence10.1016/j.solmat.2021.111172 ↗
29. Low-thermal budget flash light annealing for Al2O3 surface passivation10.1002/pssr.201510306 ↗
30. Increasing the efficiency of silicon heterojunction solar cells and modules by light soaking10.1016/j.solmat.2017.06.023 ↗
31. Electron-active silicon oxidation10.1007/BF00615932 ↗
32. Disturbance and recovery in high speed (110) cleavage in single crystalline silicon10.1016/j.jeurceramsoc.2017.12.035 ↗
33. Influence of cell edges on the performance of silicon heterojunction solar cells10.1016/j.solmat.2022.111605 ↗
34. Influence of the geometric parameters on the deposition mode in spatial atomic layer deposition: a novel approach to area-selective deposition10.3390/coatings9010005 ↗
35. Spatial atomic layer deposition
36. Understanding the improvement of silicon heterojunction solar cells under light soaking10.1063/5.0089284 ↗
37. Interface engineering for the passivation of c-Si with O3-based atomic layer deposited AlOx for solar cell application
38. Annealing effects of aluminum silicate films grown on Si(100)10.1116/1.1472422 ↗