journal article·2022-12Open access

Low temperature based PDINO cathode interlayer for high operational photostable inverted non-fullerene organic solar cells

Enas Moustafa, Maria Méndez, Josep Pallarès, Lluis F. Marsal

Abstract

The performance and industrial visibility of organic solar cells (OSCs) are greatly impacted by the functionality and stability of the interfacial layers. Many reported interface materials exhibited limitations in their fabrication temperature along with the operational stability toward the industrial up-scalability. In this work, a systematic analysis was conducted on the fresh and photo-aged-inverted non-fullerene organic solar cells (iNF-OSCs) with different structures of the electron transporting layers (ZnO, ZnO/PDINO, and PDINO), through studying their optical and electronic properties using external quantum efficiency measurements and impedance spectroscopy. Consequently, we presented PDINO as an efficient low temperature operation cathode interlayer for iNF-OSCs. Compared to the benchmark interface layers for i-OSCs such as ZnO, the PDINO interlayer used to replace the ZnO film, exhibiting a remarkable operational photostability. Where PDINO based iNF-OSCs demonstrated an extremely photostable behavior that is almost three times higher than the ZnO based devices under AM 1.5G (100 mW cm−2) continuous illumination conditions. This behavior might be attributed to the PDINO interlayer properties, which undergoes with no photochemical reaction with the contacted PM6:Y7 photo-active layer, avoiding the inescapable photocatalytic effect that is commonly obtained by the ZnO interlayer.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Organic Light-Emitting Diodes Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (93)

Show source-provided references
1. Key parameters requirements for non-fullerene-based organic solar cells with power conversion efficiency >20%10.1002/advs.201802028 ↗
2. Single-Junction organic photovoltaic cells with approaching 18% efficiency10.1002/adma.201908205 ↗
3. Additive-induced miscibility regulation and hierarchical morphology enable 17.5% binary organic solar cells10.1039/D0EE04012F ↗
4. Fine-tuning the energy levels of a nonfullerene small-molecule acceptor to achieve a high short-circuit current and a power conversion efficiency over 12% in organic solar cells10.1002/adma.201704904 ↗
5. Trendsetters in high-efficiency organic solar cells: toward 20% power conversion efficiency10.1002/solr.201900342 ↗
6. Progress in non-fullerene acceptor based organic solar cells10.1016/j.solmat.2018.12.033 ↗
7. Recent progress in chlorinated organic photovoltaic materials10.1021/acs.accounts.0c00009 ↗
8. 18% Efficiency organic solar cells10.1016/j.scib.2020.01.001 ↗
9. Advances in non-fullerene acceptor based ternary organic solar cells10.1002/solr.201700158 ↗
10. High-performance nonfullerene organic solar cells with unusual inverted structure10.1002/solr.202000115 ↗
11. Functionality of non-fullerene electron acceptors in ternary organic solar cells10.1002/solr.201900322 ↗
12. Extraordinarily long diffusion length in PM6:Y6 organic solar cells10.1039/D0TA03016C ↗
13. Single-Junction organic solar cell with over 15% efficiency using fused-ring acceptor with electron-deficient core10.1016/j.joule.2019.01.004 ↗
14. Non-fullerene acceptors with nitrogen-containing six-membered heterocycle cores for the applications in organic solar cells10.1016/j.solmat.2021.111046 ↗
15. A cost-effective, aqueous-solution-processed cathode interlayer based on organosilica nanodots for highly efficient and stable organic solar cells
16. Comparative study of light- and thermal-induced degradation for both fullerene and non-fullerene-based organic solar cells10.1039/C8SE00567B ↗
17. High-efficiency and air-stable P3HT-based polymer solar cells with a new non-fullerene acceptor10.1038/ncomms11585 ↗
18. Significant enhancement of illumination stability of nonfullerene organic solar cells via an aqueous polyethylenimine modification10.1021/acs.jpclett.1c00276 ↗
19. Increasing photostability of inverted nonfullerene organic solar cells by using fullerene derivative additives10.1021/acsami.1c00700 ↗
20. Unraveling the microstructure-related device stability for polymer solar cells based on nonfullerene small-molecular acceptors10.1002/adma.201908305 ↗
21. J. Min, acceptor additive
22. Planar heterojunctions for reduced non-radiative open-circuit voltage loss and enhanced stability of organic solar cells10.1039/D1TC01536B ↗
23. An unfused-core-based nonfullerene acceptor enables high-efficiency organic solar cells with excellent morphological stability at high temperatures
24. An operando study on the photostability of nonfullerene organic solar cells10.1002/solr.201900077 ↗
25. Highly efficient inverted polymer solar cells by using solution processed MgO/ZnO composite interfacial layers10.1016/j.jcis.2020.09.047 ↗
26. Impact of contact evolution on the shelf life of organic solar cells10.1039/b910213b ↗
27. Stability of inverted organic solar cells with ZnO contact layers deposited from precursor solutions10.1039/C4EE02488E ↗
28. Efficient inverted bulk-heterojunction solar cells from low-temperature processing of amorphous ZnO buffer layers10.1039/C4TA02276A ↗
29. High-efficiency organic solar cells based on a halide salt and polyfluorene polymer with a high alignment-level of the cathode selective contact10.1039/C8TA05778H ↗
30. Niobium doped zinc oxide nanorods as an electron transport layer for high-performance inverted polymer solar cells10.1016/j.jcis.2017.10.041 ↗
31. Effect of organic solar cells using various power O2 plasma treatments on the indium tin oxide substrate10.1016/j.jcis.2015.12.002 ↗
32. Solution-processed zinc oxide nanoparticles as interlayer materials for inverted organic solar cells10.1016/j.solmat.2012.09.007 ↗
33. A review of ZnO nanoparticles as solar photocatalysts: synthesis, mechanisms and applications10.1016/j.rser.2017.08.020 ↗
34. Electrical and photo-induced degradation of ZnO layers in organic photovoltaics10.1002/aenm.201100227 ↗
35. Stability enhancement of high-performance inverted polymer solar cells using ZnO electron interfacial layer deposited by intermittent spray pyrolysis approach10.1021/acsaem.1c00455 ↗
36. A cathode interface engineering approach for the comprehensive study of indoor performance enhancement in organic photovoltaics10.1039/D0SE00353K ↗
37. Effect of additives and annealing on the performance of nonfullerene-based binary and ternary organic photovoltaics
38. Loss mechanisms in high efficiency polymer solar cells10.1002/aenm.201501742 ↗
39. Consensus stability testing protocols for organic photovoltaic materials and devices10.1016/j.solmat.2011.01.036 ↗
40. Burn-in free nonfullerene-based organic solar cells10.1002/aenm.201700770 ↗
41. Simultaneously enhanced efficiency and operational stability of nonfullerene organic solar cells via solid-additive-mediated aggregation control
42. Comparative analysis of burn-in photo-degradation in non-fullerene COi8DFIC acceptor based high-efficiency ternary organic solar cells10.1039/C9QM00130A ↗
43. Procedures and practices for evaluating thin-film solar cell stability10.1002/aenm.201501407 ↗
44. Progress in understanding degradation mechanisms and improving stability in organic photovoltaics10.1002/adma.201603940 ↗
45. Exploiting ternary blends for improved photostability in high-efficiency organic solar cells10.1021/acsenergylett.0c00604 ↗
46. Photocatalytic effect of ZnO on the stability of nonfullerene acceptors and its mitigation by SnO2 for nonfullerene organic solar cells10.1039/C9MH00379G ↗
47. Understanding the light soaking effects in inverted organic solar cells functionalized with conjugated macroelectrolyte electron-collecting interlayers
48. Mechanism of light-soaking effect in inverted polymer solar cells with open-circuit voltage increase10.1021/acsomega.7b00097 ↗
49. Overcoming the “light-soaking” issue in inverted organic solar cells by the use of al:zno electron extraction layers10.1002/aenm.201300402 ↗
50. Understanding S-shaped current-voltage characteristics in organic solar cells containing a TiO x interlayer with impedance spectroscopy and equivalent circuit analysis10.1021/jp305206d ↗
51. Origin of the S-shaped JV curve and the light-soaking issue in inverted organic solar cells10.1002/aenm.201502265 ↗
52. Significance of light-soaking effect in proper analysis of degradation dynamics of organic solar cells10.1117/1.JPE.6.035503 ↗
53. Addressing the light-soaking issue in inverted organic solar cells using chemical bath deposited fluorinated TiOx electron transport layer10.1039/C4TA05042H ↗
54. Mechanistic investigation into the light soaking effect observed in inverted polymer solar cells containing chemical bath deposited titanium oxide10.1021/jp509879v ↗
55. Vertical phase separation and light-soaking effect improvements by photoactive layer spin coating initiation time control in air-processed inverted organic solar cells10.1016/j.solmat.2015.04.017 ↗
56. Simulation of light intensity dependent current characteristics of polymer solar cells10.1063/1.1646435 ↗
57. Degradation mechanisms in organic photovoltaic devices10.1016/j.orgel.2011.11.027 ↗
58. Determination of injection barriers in organic semiconductor devices from capacitance measurements10.1103/PhysRevLett.100.086802 ↗
59. Transient photoconductivity in polymer bulk heterojunction solar cells: competition between sweep-out and recombination10.1103/PhysRevB.83.035205 ↗
60. Recombination in polymer-fullerene bulk heterojunction solar cells10.1103/PhysRevB.82.245207 ↗
61. Light dependent open-circuit voltage of organic bulk heterojunction solar cells in the presence of surface recombination10.1016/j.orgel.2015.11.025 ↗
62. Effect of leakage current and shunt resistance on the light intensity dependence of organic solar cells10.1063/1.4913589 ↗
63. Charge carrier recombination in bulk heterojunction organic solar cells
64. Small energy loss in ternary organic solar cells with a blend of cascade energy levels: two fullerene-free acceptors as the electron acceptor10.1039/C9TC03210J ↗
65. Ring-perfluorinated non-volatile additives with a high dielectric constant lead to highly efficient and stable organic solar cells10.1039/C9TC00762H ↗
66. Recombination-limited photocurrents in low bandgap polymer/fullerene solar cells10.1002/adfm.200801514 ↗
67. Barium: An efficient cathode layer for bulk-heterojunction solar cells10.1038/srep01965 ↗
68. Understanding the light-intensity dependence of the short-circuit current of organic solar cells10.1002/adts.202000116 ↗
69. Nanoparticles on the performance of polymer bulk heterojunction solar cells10.1021/nn102295p ↗
70. Improved blend film morphology and free carrier generation provide a high-performance ternary polymer solar cell10.1021/acsami.0c19198 ↗
71. Compositional dependence of the performance of poly(p-phenylene vinylene):Methanofullerene bulk-heterojunction solar cells10.1002/adfm.200400345 ↗
72. Photocurrent generation in polymer-fullerene bulk heterojunctions10.1103/PhysRevLett.93.216601 ↗
73. Hydrogen bond induced high performance ternary fullerene-free organic solar cells with increased current density and enhanced stability10.1039/C8TC03004A ↗
74. High-efficiency organic solar cells with low non-radiative recombination loss and low energetic disorder10.1038/s41566-019-0573-5 ↗
75. Interfacial disorder in efficient polymer solar cells: the impact of donor molecular structure and solvent additives10.1039/C7TA07924A ↗
76. Single-junction polymer solar cells with high efficiency and photovoltage10.1038/nphoton.2015.6 ↗
77. The long-wavelength edge of photographic sensitivity and of the electronic Absorption of Solids [8]10.1103/PhysRev.92.1324 ↗
78. The mechanism of burn-in loss in a high efficiency polymer solar cell10.1002/adma.201103010 ↗
79. Relating recombination, density of states, and device performance in an effi cient polymer:fullerene organic solar cell blend10.1002/aenm.201300194 ↗
80. Impedance spectroscopy for emerging photovoltaics10.1021/acs.jpcc.9b00892 ↗
81. Charge carrier mobility and lifetime of organic bulk heterojunctions analyzed by impedance spectroscopy10.1016/j.orgel.2008.06.007 ↗
82. Degradation effects related to the hole transport layer in organic solar cells10.1002/adfm.201100429 ↗
83. Charge carrier traps in organic semiconductors: a review on the underlying physics and impact on electronic devices10.1039/C9TC05695E ↗
84. Determination of defect distributions from admittance measurements and application to Cu(In,Ga)Se2 based heterojunctions10.1063/1.363401 ↗
85. Pathway for recovery of photo-degraded polymer solar cells by post degradation thermal anneal10.1016/j.solmat.2017.02.012 ↗
86. Tail state limited photocurrent collection of thick photoactive layers in organic solar cells10.1038/s41467-019-12951-7 ↗
87. Interpreting the density of states extracted from organic solar cells using transient photocurrent measurements10.1021/jp4010828 ↗
88. Insights from transient optoelectronic analyses on the open-circuit voltage of organic solar cells10.1021/jz300293q ↗
89. Degradation analysis of encapsulated and nonencapsulated TiO2/PTB7:PC70BM/V2O5 solar cells under ambient conditions via impedance spectroscopy10.1021/acsomega.7b00534 ↗
90. A Debye dispersion model of a two-layered material10.1063/1.5085377 ↗
91. Poole-Frenkel-effect as dominating current mechanism in thin oxide films - an illusion?10.1063/1.4921949 ↗
92. Highly efficient halogen-free solvent processed small-molecule organic solar cells enabled by material design and device engineering10.1039/C7EE00805H ↗
93. Improved efficiency of bulk heterojunction polymer solar cells by doping low-bandgap small molecules10.1021/am500074s ↗