Localisation of front side passivating contacts for direct metallisation of high-efficiency c-Si solar cells
Source abstract
Abstract
In this work, we present the development of passivating contacts based on thin interfacial oxide/doped poly-silicon for two side contacted c-Si solar cells. In the first part, we discuss our layer optimization towards direct metallisation, using firing through of Ag-paste screen printed on a silicon nitride (SiNx:H). By optimising the poly-silicon thickness, we obtain solar cells with open circuit voltage (VOC) up to 700 mV and fill factor (FF) up to 78%. However, such results were obtained by using layers with a thickness of 95 nm, strongly limiting the short circuit current density. To overcome this limitation, we present in the second part an approach for localization of the front side passivating contact by means of deposition through a shadow mask. Finally, in the third part, we demonstrate high-efficiency c-Si solar cells with promising efficiency above 21.7% with a VOC of ∼711 mV, a high FF of 79.7% and a potential for efficiency >22%.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies · Integrated Circuits and Semiconductor Failure Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (35)
Show source-provided references
1. Physical model of back line-contact front-junction solar cells10.1063/1.4800840 ↗
2. Accurate opto-electrical modeling of multi-crystalline silicon wafer-based solar cells10.1016/j.solmat.2013.12.019 ↗
3. Industrial high performance crystalline silicon solar cells and modules based on rear surface passivation technology10.1016/j.solmat.2013.06.025 ↗
4. Silicon heterojunction solar cell with interdigitated back contacts for a photoconversion efficiency over 2610.1038/nenergy.2017.32 ↗
5. n-Type Si solar cells with passivating electron contact: identifying sources for efficiency limitations by wafer thickness and resistivity variation10.1016/j.solmat.2017.05.042 ↗
6. Laser contact openings for local poly-Si-metal contacts enabling 26.1%-efficient POLO-IBC solar cells
7. Design rules for high-efficiency both-sides-contacted silicon solar cells with balanced charge carrier transport and recombination losses10.1038/s41560-021-00805-w ↗
8. Large area tunnel oxide passivated rear contact n-type Si solar cells with 21.2% efficienc10.1002/pip.2739 ↗
9. Recombination behavior and contact resistance of n+ and p+ poly-crystalline Si/mono-crystalline Si junctions10.1016/j.solmat.2014.06.003 ↗
10. Passivated rear contacts for high-efficiency n-type Si solar cells providing high interface passivation quality and excellent transport characteristics10.1016/j.solmat.2013.09.017 ↗
11. Passivating electron contact based on highly crystalline nanostructured silicon oxide layers for silicon solar cells10.1016/j.solmat.2016.06.040 ↗
12. Design and application of ion-implanted polySi passivating contacts for interdigitated back contact c-Si solar cells10.1063/1.4940364 ↗
13. Ingenito · 2018 · 1
14. Crystalline silicon solar cells with coannealed electron- and hole-selective SiC x passivating contacts
15. Recombination analysis of phosphorus-doped nanostructured silicon oxide passivating electron contacts for silicon solar cells10.1109/JPHOTOV.2017.2779871 ↗
16. Building blocks for industrial , screen-printed double-side contacted POLO cells with highly transparent ZnO : Al layers10.1109/JPHOTOV.2018.2813427 ↗
17. Dissociation kinetics of hydrogen-passivated defects at the interface10.1103/PhysRevB.61.8393 ↗
18. Surface passivation of crystalline silicon solar cells: a review10.1002/1099-159X(200009/10)8:5<473::AID-PIP337>3.0.CO;2-D ↗
19. The role of hydrogenation and gettering in enhancing the efficiency of next-generation Si solar cells: an industrial perspective
20. Analysis of Hydrogen Distribution and Migration in Fired Passivating contacts10.1016/j.solmat.2019.110018 ↗
21. 24.58% total area efficiency of screen-printed, large area industrial silicon solar cells with the tunnel oxide passivated contacts (i-TOPCon) design10.1016/j.solmat.2019.110258 ↗
22. Development of thin polysilicon layers for application in monoPolyTM cells with screen-printed and fired metallization10.1016/j.solmat.2019.110358 ↗
23. TOPCon – technology options for cost efficient industrial manufacturing10.1016/j.solmat.2021.111100 ↗
24. Yan · 2021
25. Ingenito · 2017 · 4
26. Simple processing of back-contacted silicon heterojunction solar cells using selective-area crystalline growth10.1038/nenergy.2017.62 ↗
27. Evolutionary PERC+ solar cell efficiency projection towards 24% evaluating shadow-mask-deposited poly-Si fingers below the Ag front contact as next improvement step10.1016/j.solmat.2020.110586 ↗
28. Measurement of the emitter saturation current by a contactless photoconductivity decay method
29. Quasi-steady-state photoconductance, a new method for solar cell material and device characterization
30. Prediction of the open‐circuit voltage of solar cells from the steady‐state photoconductance10.1002/(SICI)1099-159X(199703/04)5:2<79::AID-PIP155>3.0.CO;2-J ↗
31. Profilometry of thin films on rough substrates by Raman spectroscopy10.1038/srep37859 ↗
32. Parasitic absorption in polycrystalline Si-layers for carrier-selective front junctions10.1016/j.egypro.2016.07.057 ↗
33. Phosphorous-doped silicon carbide as front-side full-area passivating contact for double-side contacted c-Si solar cells10.1109/JPHOTOV.2018.2886234 ↗
34. Influence of the carbon concentration on (p) poly-SiC x layer properties with focus on parasitic absorption in front side poly-SiC x/SiO x passivating contacts of solar cells10.1109/JPHOTOV.2020.3023506 ↗
35. Optical model for thin-film photovoltaic devices with large surface textures at the front side