N-type single-crystalline Si solar cells: Front side metallization for solar cells reaching 20% efficiency
Source abstract
Abstract
Abstract Screen printed front side contacts were investigated in n-type, high efficiency, single-crystalline Si solar cells with B doped emitters. Cells were processed identically and two different front side pastes were used: paste Ag–Al yielded efficiencies of 20.0%, and paste Ag, without Al, yielded 16.1% efficiency only. Cells contacted with paste Ag–Al yielded a continuous glass layer, a significantly higher density of Ag colloids, and an Al mole fraction of ∼1 at%. In contrast, cells contacted with paste Ag revealed a thinner but continuous glass layer as compared to cells processed with paste Ag–Al. It contained a lower density of Ag colloids and Al was below the detection limit of the EDX microanalysis. In n-type cells pyramidal shaped Ag nanocrystals did not appear, whereas for p-type cells they are formed at intersections of differently {111} oriented surface planes at the Si emitter. We did not find Ag/Al spikes at the Si emitter for cells contacted with paste Ag–Al. Cells contacted with paste Ag–Al had a smaller series resistance as well as a significantly lower specific contact resistance (4 mΩ cm2). A higher series resistance and specific contact resistance >100 mΩ cm2 was found for cells contacted with paste Ag. It was concluded that the specific contact resistance decreases with increased wetting and increased density of Ag colloids in the glass layer. The series resistance of the Ag–Al alloy contact depended only weakly on temperature, whereas the series resistance linearly increased with temperature for contacts processed with paste Ag. p- and n-type cells with maximum efficiency yield a similar microstructure of the front side contact, similar series and contact resistance, respectively. A high density of Ag colloids in the glass layer was found for cells with low specific contact resistance. This suggests that also for n-type cells a three dimensional percolative charge transport through the glass layer is assisted by the presence of metallic Ag colloids.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Nanowire Synthesis and Applications · Semiconductor materials and interfaces
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. P-type versus n-type silicon wafers: Prospects for high-efficiency commercial silicon solar cells10.1109/TED.2006.878026 ↗
2. Recombination activity of interstitial iron and other transition metal point defects in p- and n-type crystalline silicon10.1063/1.1812833 ↗
3. Advancements in n-type base crystalline silicon solar cells and their emergence in the photovoltaic industry10.1155/2013/470347 ↗
4. Physical understanding of printed thick-film front contacts of crystalline Si solar cells-Review of existing models and recent developments10.1016/j.solmat.2006.03.040 ↗
5. High-temperature contact formation on n-Type silicon: basic reactions and contact model for seed-layer contacts10.1002/adfm.200901305 ↗
6. R. Kopecek, T. Buck, J. Libal, R. Petres, K. Wambach, R. Kinderman, et al., Large area N-type multicrystalline silicon solar cells with B-emitter: efficiencies exceeding 14%, in: Proceedings of the 15th International Photovoltaic Science and Engineering Conference, 2005, pp. 3–4.
7. Screen printing metallization of B emitters10.1002/pip.933 ↗
8. Formation of Ag/Al screen-printing contacts on B emitters10.1109/JPHOTOV.2014.2364117 ↗
9. Influence of emitter properties on contact formation to p+ silicon10.1016/j.egypro.2013.07.338 ↗
10. Microscopic origin of the aluminium assisted spiking effects in n-type silicon solar cells10.1016/j.solmat.2014.05.036 ↗
11. Improving screen printed metallization for large area industrial solar cells based on n-type material10.1016/j.egypro.2011.06.171 ↗
12. Review on screen printed metallization on p-type silicon10.1016/j.egypro.2012.05.003 ↗
13. Impact of B doping profiles on the specific contact resistance of screen printed Ag–Al contacts on silicon
14. Metallization-induced recombination losses of bifacial silicon solar cells10.1002/pip.2479 ↗
15. Silver thick-film contacts on highly doped n-type silicon emitters: structural and electronic properties of the interface10.1063/1.1562338 ↗
16. Electron microscopy study of front-side Ag contact in crystalline Si solar cells
17. Contact formation of front side metallization in p-type, single crystalline Si solar cells: microstructure, temperature dependent series resistance and percolation model10.1016/j.solmat.2015.10.042 ↗
18. Series and contact resistance measurements between 80K and room temperature for industrial solar cells10.1016/j.egypro.2015.03.287 ↗
19. V.D. Mihailetchi, J. Jourdan, A. Edler, R. Kopecek, R. Harney, D. Stichtenoth, J. Lossen, T.S. Böscke, H.-J. Krokoszinsk, Screen printed n-type silicon solar cells for industrial application, in: Proceedings of the 25th European Photovoltaic Solar Energy Conference and Exhibition, 2010, pp. 6–10. Doi:10.4229/25thEUPVSEC2010–2DO.2.2.
20. Combined microstructural and electrical characterization of metallization layers in industrial solar cells10.1016/j.egypro.2015.03.285 ↗
21. A review and comparison of different methods to determine the series resistance of solar cells10.1016/j.solmat.2007.05.026 ↗
22. Front side metallization of n- and p-type, high-efficiency, single-crystalline Si solar cells: assessing the temperature dependent series resistance10.1007/s11664-016-4459-8 ↗
23. Fineline printing options for high efficiencies and low Ag paste consumption10.1016/j.egypro.2013.07.339 ↗
24. J. Engelhardt, A. Frey, S. Fritz et.al, Contact formation on boron doped silicon substrates from passivating PECV-deposited dielectric doping layers with anti-reflective properties by screen printing Ag Pastes for high efficiency n-Type Silicon Solar Cells, in: 31st EUPVSEC, Hamburg, Germany, 2015.
25. Contacting boron emitters on n-type silicon solar cells with aluminium-free silver screen-printing pastes10.1002/pssr.201510443 ↗
26. Mechanism for the formation of Ag crystallites in the Ag thick-film contacts of crystalline Si solar cells10.1016/j.solmat.2008.10.021 ↗
27. Effect of glass frit chemistry on the physical and electrical properties of thick-film Ag contacts for silicon solar cells10.1007/s11664-006-0311-x ↗
28. A.G. Aberle, S.R. Wenham, M.A. Green, A new method for accurate measurements of the lumped series resistance of solar cells, in: Proceedings of the 23rd IEEE Photovoltaic Specialist Conference, 1993, pp. 133–139. Doi: 10.1109/PVSC.1993.347065.10.1109/PVSC.1993.347065 ↗
29. Comprehensive analysis of advanced solar cell contacts consisting of printed fine-line seed layers thickened by silver plating10.1002/pip.855 ↗
30. Mechanism underlying the beneficial effect of forming gas annealing on screen-printed Ag contacts of crystalline Si solar cells10.1016/j.actamat.2014.02.023 ↗
31. Fabrication of novel three-dimensional microstructures by the anisotropic etching of (100) and (110) silicon10.1109/T-ED.1978.19249 ↗
32. Selective chemical etching of polycrystailine SiGe alloys with respect to Si and SiO2
33. Metal-assisted chemical etching of Silicon : a review10.1002/adma.201001784 ↗
34. H. Kerp, S. Kim, R. Lago, F. Recart, I. Freire, L. Pérez, et al., Development of screen printable contacts for p+ emitters in bifacial solar cells, in: Proceedings of the 21st European Photovoltaic Solar Energy Conference, 2006, pp. 892–894.
35. S. Seyedmohammadi, E. Graddy, A. Shaikh, Screen printable Ag–Al metal pastes for P+ silicon application in solar cells, in: IEEE Photovoltaic Specialists Conference, 2010, pp. 3600–3603. Doi:10.1109/PVSC.2010.5614384.10.1109/PVSC.2010.5614384 ↗
36. Current conduction mechanism of front-side contact of N-type crystalline Si solar with Ag/Al pastes10.1109/JPHOTOV.2013.2292350 ↗
37. Microstructure characterization and current conduction mechanisms of front-side contact of n-type crystalline Si solar cells with Ag/Al pastes10.1063/1.4921544 ↗
38. Understanding the formation and temperature dependence of thick-film Ag contacts on high-sheet-resistance Si emitters for solar cells10.1149/1.2001507 ↗