Industrial TOPCon solar cells on n-type quasi-mono Si wafers with efficiencies above 23%
Source abstract
Abstract
Abstract Since 2017, the efficiency record for cast multi-crystalline silicon (mc-Si) solar cells has been 22.3% using a TOPCon design on a 2 × 2 cm2 area of an n-type wafer processed in the laboratory. As the efficiency of industrial PERC and TOPCon cells on monocrystalline wafers has been higher than that, there is widespread expectation that multi-crystalline materials will be used less and less. Recently, we applied our industrial TOPCon (i-TOPCon) technology to 157.4 mm × 157.4 mm quasi-mono n-type wafers and achieved an efficiency of 23.22% with Voc of 711.9 mV with illumination for the front side, independently confirmed by ISFH CalTeC in Germany. To the best of our knowledge, this is the first solar cell based on cast-mono material that exceed 23% efficiency. This gives scope that cast materials may still be used in future cell fabrication because such high efficiencies and lower cost may offset the lower production yield compared to Czochralski (Cz) wafers. We report on details about our cell structure and processing, we analyze the bulk lifetime before and after cell fabrication, and give details about the optimization of the rear passivating contact.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Thin-Film Transistor Technologies · Semiconductor materials and interfaces
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. Classification of recombination active defect structures in multicrystalline silicon solar cells10.1016/j.egypro.2011.06.097 ↗
2. The electrical properties of high performance multicrystalline silicon and mono-like silicon: material limitations and cell potential10.1016/j.solmat.2019.110059 ↗
3. High-efficiency n-type HP mc silicon solar cells10.1109/JPHOTOV.2017.2714139 ↗
4. 23.83% efficient mono-PERC incorporating advanced hydrogenation10.1002/pip.3243 ↗
5. Passivated rear contacts for high-efficiency n-type Si solar cells providing high interface passivation quality and excellent transport characteristics10.1016/j.solmat.2013.09.017 ↗
6. Mass production of industrial tunnel oxide passivated contacts (i-TOPCon) silicon solar cells with average efficiency over 23% and modules over 345 W10.1002/pip.3180 ↗
7. About the origin of low wafer performance and crystal defect generation on seed-cast growth of industrial mono-like silicon ingots10.1002/pip.2344 ↗
8. High efficiency multicrystalline silicon solar cells: potential of n-type doping
9. P-type multicrystalline silicon substrate
10. A Quasi-Steady-State open-circuit voltage method for solar cell characterization
11. Superacid-derived surface passivation for measurement of ultra-long lifetimes in silicon photovoltaic materials10.1016/j.solmat.2018.03.028 ↗
12. Tunnel oxide passivated contacts formed by ion implantation for applications in silicon solar cells10.1063/1.4936223 ↗
13. Phosphorus-diffused polysilicon contacts for solar cells10.1016/j.solmat.2015.06.001 ↗
14. Improved evaluation of saturation currents and bulk lifetime in industrial Si solar cells by the quasi steady state photoconductance decay method10.1016/j.solmat.2016.01.032 ↗
15. 24.58% total area efficiency of screen-printed, large area industrial silicon solar cells with the tunnel oxide passivated contacts (i-TOPCon) design10.1016/j.solmat.2019.110258 ↗
16. Optical and recombination properties of dislocations in cast-mono silicon from short wave infrared luminescence imaging10.1063/1.5140245 ↗