Progress with screen printed metallization of silicon solar cells - Towards 20 μm line width and 20 mg silver laydown for PERC front side contacts
Source abstract
Abstract
Within this work, we evaluate and compare different high-end screens for the fine line front side metallization of passivated emitter and rear cell (PERC) solar cells. Three types of high-end screens are considered including (i) a fine mesh screen configuration with a mesh count MC = 520 wires/inch and standard mesh angle of φ = 22.5°, (ii) a knotless screen configuration with a mesh angle of φ = 0° as well as (iii) a knotless screen configuration utilizing a rectangular mesh with different mesh count in warp and weft direction MC = 460/430 wires/inch. Using these advanced screen configurations, all PERC solar cells are metallized with a busbarless fine line front side grid at a nominal contact finger opening of 20 μm and 24 μm. All screen configurations obtained excellent results regarding finger geometry, silver laydown and electrical performance of the front side grid and the fabricated PERC solar cells. The most efficient group obtained a printed mean finger width of 21 μm with a silver laydown of only 19 mg and revealed a mean energy conversion efficiency of 22.7%. Furthermore, we investigate the geometric and electric results of the printed front side contacts in detail using advanced image analysis software and scanning electron microscopy and discuss the impact of the fine line front side metallization on the applicable cell interconnection concepts depending on the series resistance losses.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Silicon and Solar Cell Technologies · Semiconductor materials and interfaces · Thin-Film Transistor Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. Recent advancements in low cost solar cell processing
2. 2021
3. Potential of both-sides contacted solar cells
4. Aerosol-printed silicon solar cell exceeding 20% efficiency
5. Advanced screen printing technique for high definition front side metallization of crystalline silicion solar cells
6. Industrial type Cz Silicon Cells with screen-printed fine line front contacts and passivated rear contacted by laser firing
7. Clement · 2009
8. High accuracy, high aspect ratio metallization on silicon solar cells using a print on print process
9. Double printing of front contact Ag in c-Si solar cells
10. Understanding the impact of double screen-printing on silicon solar cells by 2-D numerical simulations
11. 18,9 %-efficient screen-printed solar cells applying a print-on-print process
12. Technological and economic assessment of two-steps printing processes in a mc-Si solar cells production environment10.1016/j.egypro.2012.05.004 ↗
13. Towards 20% efficient large-area screen-printed rear-passivated silicon solar cells10.1002/pip.1198 ↗
14. Screen printed metal contacts to Si solar cells – formation and synergistic improvements
15. Reliable metallization process for ultra fine line printing10.1016/j.egypro.2013.11.091 ↗
16. Record low Ag paste consumption of 67.7 mg with dual print10.1016/j.egypro.2013.11.089 ↗
17. Fineline printing options for high efficiencies and low Ag paste consumption10.1016/j.egypro.2013.07.339 ↗
18. Improvement of the solar cell efficiency by fine line print on print technology
19. Double Printing Feasibility of 35um Printed Ag Finger Width
20. H. Hannebauer, T. Dullweber, U. Baumann, T. Falcon, R. Brendel, 21.2%‐efficient fineline‐printed PERC solar cell with 5 busbar front grid, Phys. Status Solidi Rapid Res. Lett. 8 pp. 675–679. https://doi.org/10.1002/pssr.201409190.10.1002/pssr.201409190 ↗
21. Fine line double printing and advanced process control for cell manufacturing10.1016/j.egypro.2015.03.295 ↗
22. Cell efficiency improvement of fully implanted nPERT solar cells realized through metallization optimization
23. Fine line double printing + for today and tomorrow cell metallization and interconnection
24. Galiazzo · 2017
25. Key aspects for fabrication of p-type Cz-Si PERC solar cells exceeding 22% conversion efficiency
26. Screen printed thick film metallization of silicon solar cells - recent developments and future perspectives
27. Project FINALE" - screen and screen printing process development for ultra-fine-line contacts below 20 μm finger width
28. Improving wall slip behavior of silver pastes on screen emulsions for fine line screen printing10.1016/j.solmat.2019.109969 ↗
29. Front side optimization on boron-and gallium-doped Cz-Si PERC solar cells exceeding 22% conversion efficiency
30. Screen pattern simulation for an improved front‐side Ag‐electrode metallization of Si‐solar cells10.1002/pip.3313 ↗
31. Printing technologies for silicon solar cell metallization - a comprehensive review
32. Design considerations for multi-terawatt scale manufacturing of existing and future photovoltaic technologies: challenges and opportunities related to silver, indium and bismuth consumption10.1039/D1EE01814K ↗
33. A passivated rear contact for high-efficiency n-type Silicon solar cells enabling high Vocs and FF > 82%
34. Carrier-selective contacts for Si solar cells10.1063/1.4875904 ↗
35. High-efficiency silicon heterojunction solar cells: a review10.1515/green-2011-0018 ↗
36. The link between Ag‐paste rheology and screen‐printed solar cell metallization10.1002/admt.202000654 ↗
37. Screen-printing process development towards 20μm front-side Ag electrodes on Si solar cells
38. Studying knotless screen patterns for fine-line screen printing of Si-solar cells10.1109/JPHOTOV.2019.2959939 ↗
39. Impact of texture roughness on the front-side metallization of stencil-printed silicon solar cells10.1109/JPHOTOV.2015.2416916 ↗
40. S. Tepner, L. Ney, M. Linse, A. Lorenz, M. Pospischil, K. Masuri, F. Clement, Advances in Screen Printing Metallization for Si-solar cells – Towards Ultra Fine-line Contact Fingers Below 20μm, 29th International PV Science and Engineering Conference (PVSEC-29), 4-8 November, Xi'an, China (2019).
41. A model for screen utility to predict the future of printed solar cell metallization10.1038/s41598-021-83275-0 ↗
42. Screen utility simulation - explaining the evolution and future of screen printed metallization of Si-solar cells
43. Laser enhanced contact optimization (LECO) and LECO-Specific pastes: a novel technology for improved cell efficiency
44. Paste rheology correlating with dispensed finger geometry10.1109/JPHOTOV.2013.2278657 ↗
45. Optimizing fine line dispensed contact grids10.1016/j.egypro.2014.08.046 ↗
46. Fakhfouri