Structure and thermal stability of spectrally selective absorber based on AlCrON coating for solar-thermal conversion applications
Source abstract
Abstract
Abstract A novel four-layered Mo/AlCrON(HMVF)/AlCrNO(LMVF)/AlCrOx tandem coating was designed and fabricated by cathodic arc ion plating for solar-thermal conversion applications. The chemical composition, structures and thermal stability of the coating were systematically investigated by SEM, EPMA, XRD, TEM, XPS and Raman. The optical properties of the as-deposited and annealed coatings were measured by spectrophotometers. The high-temperature emittance of the coating was measured by a steady-state measurement system. Results showed that tandem coating exhibited a high solar absorptance of 0.921, and a low emittance of 0.12 at 25 °C, as well as emittance of 0.26–0.35 at temperatures range of 300−519 °C. The structure analysis showed that the nano-multilayered structured HMVF and LMVF layers, acting as the main absorber, were consisted of the Cr 2 Al nanograins embedding in the amorphous AlCrON phases. While the top AlCrOx layer was amorphous in nature, and could act as an antireflection layer. After heat-treatment at 600 °C in air for 7 days, only slight microstructure changes were observed from the tandem coating, and very similar solar selectivity of 0.922/0.14 to the as-deposited one was obtained, which indicated the relatively good thermal stability of the coating. These results indicated that the coating could be possibly applied to the high temperature solar-thermal conversion system.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Solar Thermal and Photovoltaic Systems · Solar-Powered Water Purification Methods · Phase Change Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. A review of cermet-based spectrally selective solar absorbers10.1039/c3ee43825b ↗
2. Optimization of solar absorbing three-layer coatings10.1016/j.solmat.2005.03.009 ↗
3. Optical design and co-sputtering preparation of high performance Mo-SiO2 cermet solar selective absorbing coating10.1016/j.apsusc.2013.04.142 ↗
4. Enhanced thermal stability of W-Ni-Al2O3 cermet-based spectrally selective solar absorbers with tungsten infrared reflectors10.1002/aenm.201401042 ↗
5. High efficiency Mo-Al2O3 cermet selective surfaces for high-temperature application10.1016/0927-0248(95)00078-X ↗
6. Fabrication and optimisation of highly efficient cermet-based spectrally selective coatings for high operating temperature10.1016/j.tsf.2009.03.191 ↗
7. TiAlN/TiAlON/Si3N4 tandem absorber for high temperature solar selective applications10.1063/1.2387897 ↗
8. Deposition and characterization of TiAlN/TiAlON/Si3N4 tandem absorbers prepared using reactive direct current magnetron sputtering10.1016/j.tsf.2007.10.113 ↗
9. Preparation and thermal stability on non-vacuum high temperature solar selective absorbing coatings10.1007/s11434-009-0159-6 ↗
10. The spectral properties and thermal stability of NbTiON solar selective absorbing coating10.1016/j.solmat.2011.09.034 ↗
11. Design and fabrication of highly thermally stable HfMoN/HfON/Al2O3 tandem absorber for solar thermal power generation applications10.1016/j.solmat.2012.03.021 ↗
12. High performance multi-scaled nanostructured spectrally selective coating for concentrating solar power10.1016/j.nanoen.2014.06.016 ↗
13. Large-scale nanophotonic solar selective absorbers for high-efficiency solar thermal energy conversion10.1002/adma.201501686 ↗
14. Oxidation studies of CrAlON nanolayered coatings on steel plates10.1016/j.surfcoat.2006.02.053 ↗
15. Structural and mechanical properties of Cr-Al-O-N thin films grown by cathodic arc deposition10.1016/j.actamat.2012.08.010 ↗
16. Theiss · 2012
17. Macroparticle contamination in cathodic arc coatings: generation, transport and control10.1016/0257-8972(92)90369-L ↗
18. R.J. Lad, Multifunctional Silicon Aluminum Oxynitride (SiAlON) Ceramic Coatings for High Temperature Applications, Final performance Report, AFOSR Grant # F49620-02-1-0323, 2006.
19. Profiling nitrogen in ultrathin silicon oxynitrides with angle-resolved x-ray photoelectron spectroscopy10.1063/1.373090 ↗
20. Optical constants of sputtered Ni/NiO solar absorber film—depth-profiled characterization10.1016/j.solmat.2003.12.014 ↗
21. Pt-Al2O3 selective cermet coatings on superalloy substrates for photothermal conversion up to 600°C10.1016/0040-6090(85)90169-5 ↗
22. Stability of W-Al2O3 cermet based solar coating for receiver tube operating at high temperature10.1016/j.solmat.2010.04.080 ↗
23. High performance W-AlN cermet solar coatings designed by modelling calculations and deposited by DC magnetron sputtering10.1016/j.solmat.2003.08.021 ↗
24. A steady-state measurement system for total hemispherical emissivity10.1088/0957-0233/23/2/025006 ↗
25. Transient calorimetric measurement method for total hemispherical emissivity10.1115/1.4006896 ↗
26. Simultaneous measurements of high-temperature total hemispherical emissivity and thermal conductivity using a steady-state calorimetric technique10.1088/0957-0233/26/1/015003 ↗
27. Raman spectroscopy and x-ray diffraction of phase transitions in Cr2O3 to 61GPa10.1103/PhysRevB.69.144107 ↗
28. Properties of titanium nitride films for barrier metal in aluminum ohmic contact systems10.1143/JJAP.30.1447 ↗
29. Farooq M S, Kotecki D E, Rita R A, et al. High Temperature, conductive Thin Film Diffusion Barrier for Ceramic/Metal systems: U.S. Patent 6,178,082. 2001-1-23.