journal article·2015-03

Optical simulation and experimental optimization of Al/NbMoN/NbMoON/SiO2 solar selective absorbing coatings

Yongxin Wu, Cong Wang, Ying Sun, Yafei Xue, Yuping Ning, Wenwen Wang, Shuxi Zhao, Eric Tomasella, Angélique Bousquet

Publisher page

Abstract

For the applications in solar thermal power, the preparation and optimization of an Al/NbMoN/NbMoON/SiO2 multilayer solar selective absorbing coating are carried out by combining experiments with optical simulation. A series of NbMoN and NbMoON single layers are deposited by magnetron reactive sputtering method with different N2/O2 gas flowing rates. And then their optical constants are obtained by fitting their reflection (R) and transmission (T) spectra in the wavelength range of 300–2500 nm using SCOUT software. These optical constants are used to design the Al/NbMoN/NbMoON/SiO2 solar selective absorbing coating so as to get the ideal spectral selectivity, i.e. high α/e ratio. According to the optical design of the coating structure, we prepared the all-layer coating, and the thickness of each layer was optimized until the best spectral selective properties are obtained. The experimental reflectance spectrum fits very well with the simulated result. The optimized solar absorbing coating deposited on stainless steel substrate exhibited high absorptance (α=0.948) and low emittance (e=0.050) at 80 °C. It offers a good method to quickly reach the ideal spectral selectivity through optical simulation. The thermal stability of the coating is evaluated, and it exhibits a good thermal stability in vacuum at 400 °C.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Solar Thermal and Photovoltaic Systems · solar cell performance optimization · Photovoltaic System Optimization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Review of physical vapor deposited (PVD) spectrally selective coatings for mid- and high-temperature solar thermal applications10.1016/j.solmat.2011.10.028 ↗
2. Kennedy · 2002
3. Microstructure and spectral selectivity of Mo–Al2O3 solar selective absorbing coatings after annealing10.1016/j.tsf.2007.07.193 ↗
4. Improvement of thermal stability in the solar selective absorbing Mo–Al2O3 coating10.1016/j.solmat.2012.11.010 ↗
5. Spectral properties and thermal stability of solar selective absorbing AlNi–Al2O3 cermet coating10.1016/j.solener.2013.07.012 ↗
6. New method to optimize a solar absorber graded film profile10.1016/j.solener.2004.06.010 ↗
7. Optical property and thermal stability of Mo/Mo–SiO2/SiO2 solar-selective coating prepared by magnetron sputtering10.1002/pssa.201026301 ↗
8. The optical design of Mo two-dimensional surface gratings for high-temperature solar selective absorption surface
9. Activation energy measurement of Cu/SS-AlN/SiAlOx solar selective absorbing coating10.4028/www.scientific.net/MSF.743-744.870 ↗
10. Thermal stability of Mo-SiO2 solar selective coating at high temperature in air
11. Optical properties and thermal stability of pulsed-sputter-deposited AlxOy/Al/AlxOy multilayer absorber coatings10.1016/j.solmat.2008.11.005 ↗
12. Structure, optical properties and thermal stability of pulsed sputter deposited high temperature HfOx/Mo/HfOx solar selective absorbers10.1016/j.solmat.2010.04.073 ↗
13. Aqueous solution-chemical derived Ni–Al2O3 solar selective absorbing coatings10.1016/j.solmat.2012.05.030 ↗
14. Microstructure and optical characterization of magnetron sputtering NbN thin layers10.1016/S1000-9361(07)60021-1 ↗
15. Very low emittance solar selective surfaces using new film structures10.1063/1.351510 ↗
16. Microstructure and thermal stability of Al/Ti0.5Al0.5N/Ti0.25Al0.75N/AlN solar selective coating10.1016/j.solmat.2012.12.010 ↗
17. The spectral properties and thermal stability of NbTiON solar selective absorbing coating10.1016/j.solmat.2011.09.034 ↗
18. Spectrally selectiveNbAlN/NbAlON/Si3N4 tandem absorber for high-temperature solar applications10.1016/j.solmat.2007.11.004 ↗
19. TiAlN/TiAlON/Si3N4 tandem absorber for high temperature solar selective applications10.1063/1.2387897 ↗
20. Deposition and characterization of TiAlN/TiAlON/Si3N4 tandem absorbers prepared using reactive direct current magnetron sputtering10.1016/j.tsf.2007.10.113 ↗
21. Spectrally selective CrMoN/CrON tandem absorber for mid-temperature solar thermal applications10.1016/j.solmat.2012.10.003 ↗
22. Structure, optical properties and thermal stability of pulsed sputter deposited high temperature HfOx/Mo/HfO2 solar selective absorbers10.1016/j.solmat.2010.04.073 ↗
23. Design and fabrication of highly thermally stable HfMoN/HfON/Al2O3 tandem absorber for solar thermal power generation applications10.1016/j.solmat.2012.03.021 ↗
24. Computer simulation of the optical properties of high-temperature cermet solar selective coatings10.1016/j.solener.2004.09.024 ↗
25. Optimization of solar absorbing three-layer coatings10.1016/j.solmat.2005.03.009 ↗
26. The optical properties of sputtered composited of Al-AlN10.1016/j.solmat.2005.11.006 ↗
27. Optical modeling of multilayered coatings based on SiC(N)H materialsfor their potential use as high-temperature solar selective absorbers10.1016/j.solmat.2013.06.030 ↗
28. High performance W–AlN cermet solar coatings designed by modelling calculations and deposited by DC magnetron sputtering10.1016/j.solmat.2003.08.021 ↗
29. Zr–ZrO2 cermet solar coatings designed by modelling calculations and deposited by dc magnetron sputtering10.1088/0022-3727/36/6/315 ↗
30. Spectroscopic ellipsometric characterization of TiAlN/TiAlON/Si3N4 tandem absorber for solar selective applications10.1016/j.apsusc.2007.07.109 ↗
31. Optimization of AlxOy/Pt/AlxOy multilayer spectrally selective coatings for solar-thermal applications10.1016/j.vacuum.2012.06.012 ↗
32. Optical design and co-sputtering preparation of high performance Mo–SiO2 cermet solar selective absorbing coating10.1016/j.apsusc.2013.04.142 ↗
33. Characterization of TiAlSiN/TiAlSiON/SiO2 optical stack designed by modelling calculations for solar selective applications10.1016/j.solmat.2012.06.011 ↗
34. W. Theiss, in: M. Theiss (Ed.), SCOUT thin film analysis software handbook, Hard-and Software, Aachen, Germany. 〈http://www.mtheiss.com〉.
35. Preparation and characterization of a reference aluminum mirror10.1364/AO.41.003840 ↗
36. Determination of the reflection coefficients of laser light of wavelengths λ∈(0.22μm,200μm) from the surface of aluminum using the Lorentz-Drude model10.1364/AO.29.003479 ↗
37. Intraband and interband processes in the infrared spectrum of metallic aluminum10.1103/PhysRevB.34.5191 ↗
38. Variation of color in titanium and zirconium nitride decorative thin films10.1016/S0040-6090(02)00530-8 ↗
39. Colour control of titanium nitride coatings produced by reactive magnetron sputtering at temperature less than 100°C10.1016/S0257-8972(99)00076-6 ↗
40. The relationship between the distribution of electronic states and the optical absorption spectrum of an amorphous semiconductor: An empirical analysis10.1063/1.365643 ↗
41. Role of oxygen vacancies in the high-temperature thermopower of indium oxide and indium tin oxide films10.1088/0268-1242/24/2/025028 ↗
42. Thermal stability of sputtered zirconium oxide films10.1016/j.vacuum.2003.12.127 ↗
43. Thermal stability of amorphous molybdenum trioxide films prepared at different oxygen partial pressures by reactive DC magnetron sputtering10.1016/j.vacuum.2006.08.006 ↗
44. An infrared dielectric function model for amorphous solids10.1063/1.350737 ↗
45. Infrared properties of silicon nanoparticles10.1063/1.1866475 ↗
46. Structural properties of CuInSe2 films prepared by selenization of metallic precursors on MoNx film substrates10.1016/j.apsusc.2005.05.011 ↗