journal article·2018-03

Experimental study on the specific heat and stability of molten salt nanofluids prepared by high-temperature melting

Xia Chen, Yu-ting Wu, Lu-di Zhang, Xin Wang, Chong-fang Ma

Publisher page

Abstract

Abstract Molten salt is an important heat storage and heat transfer medium in solar thermal power generation technology due to its high heat capacity, wide working temperature range, and low cost. Adding nanoparticles (usually by the two-step method with ultrasonic dispersion) can increase the specific heat of molten salt. Thus, the molten salt nanofluids can increase the heat capacity and decrease the heat storage cost of a solar thermal power generation system. However, nanoparticles are easy to agglomerate in the molten salt; moreover, after agglomeration, the performance of molten salt nanofluids is degraded. A two-step method with high-temperature melting in preparing molten salt nanofluids is proposed in this paper. Molten salt nanofluids were prepared by high-temperature melting. The base solution was a low-melting point molten salt and the nanoparticles were SiO2 with a diameter of 20 nm. The specific heat was measured and the nanoparticle dispersity was analyzed. The stability of the molten salt nanofluids was studied, and the results were compared with those prepared by ultrasonic dispersion. The average specific heat of molten salt nanofluids prepared by high-temperature melting was 1.789 J/(g·K), which was close to that of molten salt nanofluids prepared by ultrasonic dispersion and 16.4% higher than that of pure molten salt. The molten salt nanofluids prepared by ultrasonic dispersion showed poor thermal stability under high-temperature conditions, and the average specific heat decreased by 8.5% after only 200 h. The thermal stability of molten salt nanofluids prepared by high-temperature melting showed a highly stable performance in long-time experiments. The variation of specific heat was less than 5% after 2000 h under the same high-temperature experimental condition. The molten salt nanofluids obtained by high-temperature melting showed better stability and long performance than those obtained by ultrasonic dispersion. Therefore, the two-step method with high-temperature melting is stable and reliable for preparing molten salt nanofluids.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Nanofluid Flow and Heat Transfer · Phase Change Materials Research · Solar Thermal and Photovoltaic Systems

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (35)

Show source-provided references
1. Stirling engine based solar-thermal power plant with a thermo-chemical storage system10.1016/j.enconman.2014.06.030 ↗
2. Effects of the selection of heat transfer fluid and condenser type on the performance of a solar thermal power plant with technoeconomic approach10.1016/j.enconman.2015.12.068 ↗
3. Performance analysis of a lunar based solar thermal power system with regolith thermal storage10.1016/j.energy.2016.03.132 ↗
4. Transient molten salt two-tank thermal storage modeling for CSP performance simulations10.1016/j.solener.2013.02.034 ↗
5. CFD-simulation of a new receiver design for a molten salt solar power tower10.1016/j.solener.2012.12.007 ↗
6. Ramaprasath · 2013
7. Enhanced specific heat capacity of high-temperature molten salt-based nanofluids10.1016/j.ijheatmasstransfer.2012.10.062 ↗
8. Enhanced specific heat capacity of molten salt-based nanomaterials: effects of nanoparticle dispersion and solvent material10.1016/j.actamat.2014.05.005 ↗
9. Enhanced thermal properties of SiO2 nanocomposite for solar thermal energy storage applications10.1016/j.ijheatmasstransfer.2015.01.100 ↗
10. Optimal concentration of alumina nanoparticles in molten Hitec salt to maximize its specific heat capacity10.1016/j.ijheatmasstransfer.2013.10.078 ↗
11. Zhao · 2013
12. Wu · 2013
13. A review on preparation, characterization, properties and applications of nanofluids10.1016/j.rser.2016.01.055 ↗
14. Magnetic properties of ferromagnetic ultrafine particles prepared by vacuum evaporation on running oil substrate10.1016/0022-0248(78)90482-7 ↗
15. P.X. Tran, Y. Soong, Preparation of nanofluids using laser ablation in liquid technique, ASME applied mechanics and material conference, Austin, Texas USA, 2007.
16. A novel one-step chemical method for preparation of copper nanofluids10.1016/j.jcis.2004.04.026 ↗
17. Heat transfer characteristics of nanofluids: a review10.1016/j.ijthermalsci.2006.06.010 ↗
18. Preparation and characterization of Nanofluid (CuO/Water, TiO2/Water)
19. Preparation and evaluation of stable nanofluids for heat transfer application: a review10.1016/j.expthermflusci.2016.06.029 ↗
20. Measurement of temperature-dependent thermal conductivity and viscosity of TiO2-water nanofluids10.1016/j.expthermflusci.2009.01.005 ↗
21. Thermal performance of multi-walled carbon nanotubes (MWCNTs) in aqueous suspensions with surfactants SDBS and SDS10.1016/j.icheatmasstransfer.2012.12.002 ↗
22. Experimental evaluation of thermal conductivity, viscosity and breakdown voltage AC of nanofluids of carbon nanotubes and diamond in transformer oil10.1016/j.diamond.2015.07.007 ↗
23. Heat transfer performance of different nanofluids flows in a helically coiled heat exchanger10.4028/www.scientific.net/AMR.832.160 ↗
24. Preparation and characterization of copper oxide nanofluid for heat transfer applications10.1007/s13204-012-0184-7 ↗
25. Thermoelectric cooling of electronic devices with nanofluid in a multiport minichannel heat exchanger10.1016/j.expthermflusci.2015.11.023 ↗
26. A review of nanofluid stability properties and characterization in stationary conditions10.1016/j.ijheatmasstransfer.2011.04.014 ↗
27. An investigation in to the thermophysical and rheological properties of nanofluids for solar thermal applications10.1016/j.rser.2015.10.065 ↗
28. Optimal concentration of alumina nanoparticles in molten Hitec salt to maximize its specific heat capacity10.1016/j.ijheatmasstransfer.2013.10.078 ↗
29. Preparation thermo-physical properties and heat transfer enhancement of nanofluids10.1088/2053-1591/1/3/032001 ↗
30. Stability and thermal conductivity enhancement of carbon nanotube nanofluid using gum arabic10.1080/17458080.2010.487229 ↗
31. An overview on current application of nanofluids in solar thermal collector and its challenges10.1016/j.rser.2015.09.060 ↗
32. Preparation and thermal properties of quaternary mixed nitrate with low melting point10.1016/j.solmat.2014.03.056 ↗
33. D.M. Blake, L. Moens, M.J. Hale, et al., New heat transfer and storage fluids for parabolic trough solar thermal electric plants. Proceedings of the 11th Solar PACES International Symposium On concentrating Solar Power and Chemical Energy Technologies, Zurich, Switzerland, September 4-6, 2002.
34. Effect of nanoparticle dispersion on enhancing the specific heat capacity of quaternary nitrate for solar thermal energy storage application10.1016/j.solmat.2016.07.046 ↗
35. Surface and size effects on the specific heat capacity of nanoparticles10.1007/s10765-006-0022-9 ↗