Thermal performance of hybrid cement mortar-PCMs for warm climates application
Source abstract
Abstract
In this paper, composites based on a standard mortar and two commercial microencapsulated phase change materials (PCMs) with nominal melting point of 23 degrees C and 26 degrees C in different percentage were produced and characterized. To this aim, an innovative experimental setup, able to contemporarily test two different samples subjected to the same temperature profile was designed and realized. The experimental results were then used to validate a numerical model, implemented in COMSOL Multiphysics. Finally, a parametric analysis was carried out to define optimized melting temperature for the PCM for Mediterranean application, aiming at reducing the overall energy consumption as well as to improve the comfort conditions inside buildings both during winter and summer. The results demonstrated that an optimal melting temperature of 27 degrees C is achieved under Sicilian climatic condition. Furthermore, adding 15 wt% of optimized PCM allows to improve the comfort conditions of about 15% compared to standard solutions based on pure cement mortars.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Phase Change Materials Research · Adsorption and Cooling Systems · Solar Energy Systems and Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (46)
Show source-provided references
1. European Commission, Directive 2010/31/EU of the European Parliament and of the Council of 19 May 2010 on the energy performance of buildings, 2010.
2. International Energy Agency · 2013
3. On the development of an innovative gas-fired heating appliance based on a zeolite-water adsorption heat pump; system description and seasonal gas utilization efficiency10.1016/j.applthermaleng.2014.09.008 ↗
4. Flexible heat pump or chiller with hybrid water/LiBr absorption/compression cycle10.1016/j.ijrefrig.2018.03.003 ↗
5. An innovative adsorptive chiller prototype based on 3 hybrid coated/granular adsorbers10.1016/j.apenergy.2016.07.056 ↗
6. Solar-powered absorption chillers: a comprehensive and critical review10.1016/j.enconman.2018.05.091 ↗
7. Performance of absorption chillers in field tests10.1016/j.applthermaleng.2018.02.013 ↗
8. Passive design optimization of newly-built residential buildings in Shanghai for improving indoor thermal comfort while reducing building energy demand10.1016/j.enbuild.2017.09.095 ↗
9. Preparation of energy efficient paraffinic PCMs/expanded vermiculite and perlite composites for energy saving in buildings10.1016/j.solmat.2014.11.001 ↗
10. Phase change materials and thermal energy storage for buildings10.1016/j.enbuild.2015.06.007 ↗
11. A review of phase change material and performance enhancement method for latent heat storage system10.1016/j.rser.2018.05.028 ↗
12. Identification and characterization of promising phase change materials for solar cooling applications10.1016/j.solmat.2016.10.026 ↗
13. Energy and exergy analysis of a latent heat storage system with phase change material for a solar collector10.1016/j.renene.2007.03.012 ↗
14. Application of material assessment methodology in latent heat thermal energy storage for waste heat recovery10.1016/j.apenergy.2016.11.070 ↗
15. Nano-PCMs for enhanced energy storage and passive cooling applications10.1016/j.applthermaleng.2016.03.161 ↗
16. Temperature stabilisation in Fischer–Tropsch reactors using phase change material (PCM)10.1016/j.applthermaleng.2015.08.084 ↗
17. Energy and exergy analyses of porous baffles inserted solar air heaters for building applications10.1016/j.enbuild.2012.10.055 ↗
18. Preparation, characterization and thermal regulation performance of cement based-composite phase change material10.1016/j.solmat.2017.09.049 ↗
19. Development and thermal performance of pumice/organic PCM/gypsum composite plasters for thermal energy storage in buildings10.1016/j.solmat.2015.12.034 ↗
20. Thermal performance enhancement of mortar mixed with octadecane/xGnP SSPCM to save building energy consumption10.1016/j.solmat.2013.12.015 ↗
21. Review on using microencapsulated phase change materials (PCM) in building applications10.1016/j.enbuild.2015.07.019 ↗
22. Single layer mortars with microencapsulated PCM: study of physical and thermal properties, and fire behaviour10.1016/j.enbuild.2015.11.028 ↗
23. Newly-designed traditional lime mortar with a phase change material as an additive10.1016/j.conbuildmat.2013.05.111 ↗
24. Preparation and performance of highly conductive phase change materials prepared with paraffin, expanded graphite, and diatomite10.1080/15435075.2011.546759 ↗
25. Preparation technology of phase change perlite and performance research of phase change and temperature control mortar10.1016/j.enbuild.2014.09.023 ↗
26. Experimental exploration of incorporating form-stable hydrate salt phase change materials into cement mortar for thermal energy storage10.1016/j.applthermaleng.2018.05.042 ↗
27. Incorporation of phase change materials in cementitious systems via fine lightweight aggregate10.1016/j.conbuildmat.2012.04.042 ↗
28. Thermal performance and cost analysis of mortars made with PCM and different binders10.1016/j.conbuildmat.2016.06.114 ↗
29. Experimental and theoretical analysis of a cement mortar containing microencapsulated PCM10.1016/j.applthermaleng.2014.06.053 ↗
30. Experimental and numerical studies of hybrid PCM embedded in plastering mortar for enhanced thermal behaviour of buildings10.1016/j.energy.2015.10.131 ↗
31. The effects of porosity on mechanical behavior and water absorption of an environmentally friendly cement mortar with recycled rubber10.1016/j.conbuildmat.2017.06.061 ↗
32. Sol-air temperature10.1016/0306-2619(77)90017-4 ↗
33. Ente Italiano di Normazione, UNI 10349-1:2016, 2016. 〈http://store.uni.com/catalogo/index.php/uni-10349-1-2016.html?Josso_back_to=http://store.uni.com/josso-security-check.php&josso_cmd=login_optional&josso_partnerapp_host=store.uni.com〉. (Accessed 5 June 2018).
34. Thermal enhancement of plastering mortars with Phase Change Materials: experimental and numerical approach10.1016/j.enbuild.2012.02.031 ↗
35. A review on phase-change materials: mathematical modeling and simulations10.1016/j.rser.2010.06.011 ↗
36. A simplified approach for modelling latent heat storages: application and validation on two different fin-and-tubes heat exchangers10.1016/j.applthermaleng.2017.06.142 ↗
37. Simulation-based optimization of PCM melting temperature to improve the energy performance in buildings10.1016/j.apenergy.2017.05.107 ↗
38. VDI-Wärmeatlas, Springer Berlin Heidelberg, Berlin, Heidelberg, 2002. 〈http://dx.doi.org/10.1007/978-3-662-10743-0〉.10.1007/978-3-662-10743-0 ↗
39. Influence of external surface colour on the periodic heat flow through a flat solid roof with variable thermal resistance10.1002/er.915 ↗
40. Determination and selecting the optimum thickness of insulation for buildings in hot countries by accounting for solar radiation10.1016/j.applthermaleng.2004.03.019 ↗
41. Investigation of wall's optimum insulation position from maximum time lag and minimum decrement factor point of view10.1016/S0378-7788(00)00044-X ↗
42. Experimental and theoretical investigation of effects of wall's thermophysical properties on time lag and decrement factor10.1016/S0378-7788(01)00087-1 ↗
43. Thermal enhancement of plastering mortars with Phase Change Materials: experimental and numerical approach10.1016/j.enbuild.2012.02.031 ↗
44. A.K. Athienitis, C. Liu, D. Hawes, D. Banu, D. Feldman, Investigation of the Thermal Performance of a Passive Solar Test-Room with Wall Latent Heat Storage. 〈https://ac.els-cdn.com/S0360132397000097/1-s2.0-S0360132397000097-main.pdf?_tid=1305a7d5-e1bc-4c72-8e94-27c946bcbca2&acdnat=1544029082_7db88912489c49a2db7e4ebd0b2f1dc3〉. (Accessed 5 December 2018), 1997.
45. Simulation-based optimization of PCM melting temperature to improve the energy performance in buildings10.1016/j.apenergy.2017.05.107 ↗
46. ASHRAE · 2017