Effect of B 4 C particle size on the mechanical properties of B 4 C reinforced aluminum matrix layered composite
Source abstract
Abstract
Abstract Reinforcement particle size is very important for the performance of metal ceramic composites. This work studied the influence of B 4 C particle size on the mechanical properties of Al matrix layered composites. These composites were fabricated using a simplified semicontinuous casting and hot-rolling process. To obtain an optimized filling structure of particles, Horsfield filling principle was applied to determine the size and mass fraction of B 4 C particles. Four sizes of B 4 C particles were used with various combinations. The results showed that with the increase of the B 4 C particle size and fine B 4 C mass fraction, the hardness of the composites decreases whereas the impact strength and ultimate tensile strength increase. The residual stress at interface should be responsible for the variation in properties. Besides, the interparticle distance also contributes to the change in impact strength and ultimate tensile strength.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · MXene and MAX Phase Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Laboratory of Special Processing of Raw Materials and School of Material Science and Engineering, Dalian University of Technology , Dalian, Liaoning 116024 , China
Laboratory of Special Processing of Raw Materials and School of Material Science and Engineering, Dalian University of Technology , Dalian, Liaoning 116024 , China , Tel./Fax: +86-411-8470-6220
Funding
National Natural Science Foundation of China
References (30)
Show source-provided references
1. Taha MA. Mater Manuf Process 2001, 16, 619–641.10.1081/AMP-10010862510.1081/AMP-100108625 ↗
2. Torralba JM, Da Costa CE, Velasco F. J Mater Process Technol 2003, 133, 203–206.10.1016/S0924-0136(02)00234-010.1016/S0924-0136(02)00234-0 ↗
3. Kennedy AR. J Mater Sci 2002, 37, 317–323.10.1023/A:101360032859910.1023/A:1013600328599 ↗
4. Thevenot F. J Eur Ceram Soc 1990, 6, 205–225.10.1016/0955-2219(90)90048-K10.1016/0955-2219(90)90048-K ↗
5. Zhang S, Yu YS, Tu JH, Li TJ. Adv Mater Res 2013, 602–604, 80–84.10.4028/www.scientific.net/AMR.602-604.80 ↗
6. Wang D, Xue X, Liu R, Zhang S. Mater Rev 2007, 21, 388–390.
7. Jiang L, Li Z, Fan G, Cao L, Zhang D. Carbon 2012, 50, 1993–1998.10.1016/j.carbon.2011.12.05710.1016/j.carbon.2011.12.057 ↗
8. Pan J, Ning X, Hu K, Ye H. Acta Metall Sin 1993, 6, 465–471.
9. Poddar P, Srivastava VC, De PK, Sahoo KL. Mater Sci Eng A 2007, s 460–461, 357–364.10.1016/j.msea.2007.01.052 ↗
10. Yu Y, Jie J, Zhang S. Powder Metall Met Ceram 2015, 54, 390–396.10.1007/s11106-015-9727-210.1007/s11106-015-9727-2 ↗
11. Ji X, Zhang H, Luo S, Jiang F, Fu D. Mater Sci Eng A 2016, 649, 128–134.10.1016/j.msea.2015.09.11410.1016/j.msea.2015.09.114 ↗
12. Johnsen V, Andersen PJ. Mater Sci Concretes 1991, 2, 111–146.
13. Broday DM, Agnon Y. J Aerosol Sci 2007, 38, 701–718.10.1016/j.jaerosci.2007.06.00110.1016/j.jaerosci.2007.06.001 ↗
14. Zhang T, Yu Q, Wei J, Zhang P. Cem Concr Compos 2012, 34, 692–699.10.1016/j.cemconcomp.2012.02.00410.1016/j.cemconcomp.2012.02.004 ↗
15. Fayed ME, Otten L, Eds., Handbook of Powder Science & Technology, 2nd ed., Springer USA: New York, 1997.10.1007/978-1-4615-6373-0 ↗
16. Pyzik AJ, Beaman DR. Cheminform 1996, 27, 305–312.10.1080/714041312 ↗
17. Rahimian M, Ehsani N, Parvin N, Baharvandi HR. Mater Des 2009, 30, 3333–3337.10.1016/j.matdes.2008.11.02710.1016/j.matdes.2008.11.027 ↗
18. Ferguson JB, Sheykh-Jaberi F, Kim CS, Rohatgi PK, Cho K. Mater Sci Eng A 2012, 558, 193–204.10.1016/j.msea.2012.07.11110.1016/j.msea.2012.07.111 ↗
19. Zhang Z, Chen DL. Scr Mater 2006, 54, 1321–1326.10.1016/j.scriptamat.2005.12.01710.1016/j.scriptamat.2005.12.017 ↗
20. Habibnejad-Korayem M, Mahmudi R, Poole WJ. Mater Sci Eng A 2009, 519, 198–203.10.1016/j.msea.2009.05.00110.1016/j.msea.2009.05.001 ↗
21. Williams JJ, Piotrowski G, Saha R, Chawla N. Metall Mater Trans A 2002, 33, 3861–3869.10.1007/s11661-002-0258-310.1007/s11661-002-0258-3 ↗
22. Shaw MC, Desalvo GJ. Metallography Microstruct Anal 2012, 1, 310–317.10.1007/s13632-012-0047-310.1007/s13632-012-0047-3 ↗
23. Shen YL, Chawla N. Mater Sci Eng A 2015, 297, 44–47.10.1016/S0921-5093(00)01256-9 ↗
24. Sajjadi SA, Ezatpour HR, Parizi MT. Mater Des 2012, 34, 106–111.10.1016/j.matdes.2011.07.03710.1016/j.matdes.2011.07.037 ↗
25. Ozden S, Ekici R, Nair F. Compos Part A Appl Sci Manuf 2007, 38, 484–494.10.1016/j.compositesa.2006.02.02610.1016/j.compositesa.2006.02.026 ↗
26. Kamat SV, Hirth JP, Mehrabian R. Acta Metall 1989, 37, 2395–2402.10.1016/0001-6160(89)90037-010.1016/0001-6160(89)90037-0 ↗
27. Prasad VVB, Bhat BVR, Mahajan YR, Ramakrishnan P. Mater Sci Eng A 2002, 337, 179–186.10.1016/S0921-5093(02)00024-210.1016/S0921-5093(02)00024-2 ↗
28. Hong SJ, Kim HM, Huh D, Suryanarayana C, Chun BS. Mater Sci Eng A 2003, 347, 198–204.10.1016/S0921-5093(02)00593-210.1016/S0921-5093(02)00593-2 ↗
29. Clyne TW, Withers PJ. An Introduction to Metal Matrix Composites. Cambridge University Press: New York, NY, USA, 1993.10.1017/CBO9780511623080 ↗
30. Conlon KT, Wilkinson DS. Mater Sci Eng A 2001, 317, 108–114.10.1016/S0921-5093(01)01168-610.1016/S0921-5093(01)01168-6 ↗