journal article·2025-12

Electroless Nickel Plating Process on Metallic Components of Satellite Launch Vehicles-Parametric Optimization through X-ray Fluorescent Method

Raju G, Rohit Kumar Gupta, Ashok M

Publisher page

Abstract

Electroless nickel plating (ENP) is a crucial surface treatment process for metallic hardware on satellite launch vehicles, enhancing hardness, wear resistance, and corrosion resistance. Even minor variations in plating conditions can significantly alter the ENP’s mechanical properties in combating harsh environments that are experienced during the integration and flight conditions. This research work aims to optimize the process parameters of ENP in the gas cylinders of control systems for Launch vehicles made of M250 grade Maraging steel, using the least resources and time. As the initial step, the significantly influenced process parameters were identified, and their narrower ranges were determined using the one-variable-at-a-time (OVAT) approach. In this study, the energy dispersive X-ray fluorescence (EDXRF) method was experimented with to determine the coating thickness of specimens, among other destructive, nondestructive, and dimensional methods. The EDXRF method proved to be the most accurate and consistent, comparable to microscopy, and was employed as a reliable means of assessing coating thickness for all subsequent trials. A fractional factorial design (FFD) was employed to model the optimization process, followed by a rigorous assessment of coating thickness. The optimization model was validated by the accomplishment of the required thickness within the specified range with the required measurement accuracy. The capability and characteristics of the coating, as determined by the model, were reconfirmed through energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and scanning electron microscopy (SEM) imaging and analysis. This comprehensive validation process instills confidence in the results, especially in the context of the inhospitable pre-launch and in-flight environments of the component.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Electrodeposition and Electroless Coatings · X-ray Spectroscopy and Fluorescence Analysis · Corrosion Behavior and Inhibition

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. Sahoo, P. and Das, S.K., Tribology of electroless nickel coatings—A review, Mater. Des., 2011, vol. 32, no. 4, pp. 1760–1775.10.1016/j.matdes.2010.11.013 ↗
2. Qiao, Y., Hou, J., Lai, M., and Fang, F., Control system and process optimization for electroless nickel plating, J. Nanotechnol. Precis. Eng., 2024, vol. 1, no. 2, p. 023003.10.1063/10.0034399 ↗
3. Olarewaju, A.O., Olawale, A.A., Sunday, A., et al., Fabrication and performance evaluation of electroless-nickel deposition line for metal alloys and plastic substrates, FUW Trends Sci. Technol. J., 2021, vol. 6, no. 1, pp. 069–078.
4. Ginplate Ni 425, High phosphorous electroless nickel process designed for corrosion protection and high build-up applications, Manufacturer’s Data Sheet, Growel, December 2024. https://www.growel.com.
5. Rajkumar, K.V., Vaidyanathan, S., Kumar, A., Jayakumar, T., Raj, B., and Ray, K.K., Characterization of aging-induced microstructural changes in M250 Maraging steel using magnetic parameters, J. Magn. Magn. Mater., 2007, vol. 312, no. 2, pp. 359–365.10.1016/j.jmmm.2006.10.1091 ↗
6. Giurlani, W., Berretti, E., Innocenti, M., and Lavacchi, A., Coating thickness determination using X-ray fluorescence spectroscopy: Monte Carlo simulations as an alternative to the use of standards, Coatings, 2019, vol. 9, no. 2, p. 69.10.3390/coatings9020079 ↗
7. Thakur, A., Gharde, S., and Kandasubramanian, B., Electro less nickel fabrication on surface modified magnesium substrates, Def. Technol., 2019, vol. 15, no. 4, pp. 636–644.10.1016/j.dt.2019.04.006 ↗
8. Beygi, H. and Sajjadi, S.A., Magnetic properties of crystalline nickel and low phosphorus amorphous Ni1–xPx nanoparticles, Mater. Chem. Phys., 2018, vol. 204, pp. 403–409.10.1016/j.matchemphys.2017.10.079 ↗
9. Syasko, V.A., Vasilev, A.Y., and Ivkin, A.E., Analysis of the influence of controlled and interfering parameters during magnetic testing of coating thickness, J. Phys.: Conf. Ser., 2020, vol. 1636, p. 012015. https://doi.org/10.1088/1742-6596/1636/1/01201510.1088/1742-6596/1636/1/012015 ↗
10. Zhang, L., Li, M., Li, H., and Song, X., Measurement of multilayer film thickness using X-ray fluorescence spectrometer, Key Eng. Mater., 2016, vol. 726, pp. 85–89. https://doi.org/10.4028/www.scientific.net/KEM.726.8510.4028/www.scientific.net/KEM.726.85 ↗
11. Haider, F.I., Suryanto, Ani, M.H., and Mahmood, M.H., A comparison between destructive and nondestructive techniques in determining coating thickness, IOP Conf. Ser.: Mater. Sci. Eng., 2018, vol. 290, p. 012020. https://doi.org/10.1088/1757-899X/290/1/01202010.1088/1757-899X/290/1/012020 ↗
12. Raju, G., Gupta, R.K., and Ashok, M., X-ray fluorescence methods of multi-layer coating thickness measurements on satellite launch vehicle components, Russ. J. Nondestr. Test., 2025, vol. 61, no. 1, pp. 99–114.10.1134/S1061830924603167 ↗
13. Sekatskii, V.S., et al., Two-point calibration of coating thickness gauges: What needs to be considered to improve measurement accuracy, IOP Conf. Ser.: Mater. Sci. Eng., 2019, vol. 537, p. 032068. https://doi.org/10.1088/1757-899X/537/3/03206810.1088/1757-899X/537/3/032068 ↗
14. Zaimovic-Uzunovic, N., Lemes, S., Tomasevic, D., and Kacmarcik, J., Flatness measurement on a coordinate measuring machine, Proc. 5th Int. Conf. on New Technologies, Development and Application, 2019, pp. 27–29.10.1007/978-3-030-18072-0_19 ↗
15. Ali, P. and Younas, A., Understanding and interpreting regression analysis, Evidence-Based Nurs., 2021, vol. 24, no. 4, pp. 110–111.10.1136/ebnurs-2021-103425 ↗
16. Jaynes, J., Ding, X., Xu, H., Wong, W.K., and Ho, C.M., Application of fractional factorial designs to study drug combinations, Stat. Med., 2013, vol. 32, no. 2, pp. 307–318. https://doi.org/10.1002/sim.552610.1002/sim.5526 ↗
17. Li, F., Ge, L., Tang, Z., Chen, Y., and Wang, J., Recent developments on XRF spectra evaluation, Appl. Spectrosc. Rev., 2019, vol. 54, no. 7, pp. 573–597. https://doi.org/10.1080/05704928.2019.158071510.1080/05704928.2019.1580715 ↗
18. Giurlani, W., Berretti, E., Innocenti, M., and Lavacchi, A., Measuring the Thickness of metal coatings: A review of the methods, Coatings, 2020, vol. 10, no. 12, p. 1211.10.3390/coatings10121211 ↗
19. Czitrom, V., One-factor-at-a-time versus designed experiments, Am. Stat., 1999, vol. 53, no. 2, pp. 126–131.10.1080/00031305.1999.10474445 ↗
20. Kraber, S., Statistician’s corner—What’s behind aliasing in fractional-factorial designs, J. Plast. Film Sheeting, 2022, vol. 38, no. 2, pp. 187–190.10.1177/87560879221089430 ↗
21. Sarkar, S., Mandal, R., Mondal, N., Chaudhuri, S., Mandal, T., and Majumdar, G., Modeling and prediction of micro-hardness of electroless Ni-P coatings using response surface methodology and fuzzy logic, Jordan J. Mech. Ind. Eng., 2022, vol. 16, no. 5, pp. 709–719.
22. Dvivedi, A., Rajeev, V.R., Kumar, P., and Singh, I., Tribological characteristics of Al 6063–SiCp metal–matrix composite under reciprocating and wet conditions, Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol., 2011, vol. 226, no. 2, pp. 107–117.
23. Moral, R.A., Hinde, J., and Demétrio, C.G.B., Half-normal plots and over dispersed models in R: The hnp package, J. Stat. Software 2017, vol. 81, no. 10, pp. 1–23.10.18637/jss.v081.i10 ↗
24. Sankara Narayanan, T.S., Krishnaveni, K., and Seshadri, S.K., Electro less Ni–P/Ni–B duplex coatings: Preparation and evaluation of micro hardness, wear and corrosion resistance, Mater. Chem. Phys., 2003, vol. 82, no. 3, pp. 771–779.10.1016/S0254-0584(03)00390-0 ↗