Thermoelectric detection of fretting damage in aerospace materials
Source abstract
Abstract
Fretting is a wear phenomenon that occurs when cyclic loading causes two surfaces in intimate contact to undergo small oscillatory motions with respect to each other. During fretting, high points or asperities of the mating surfaces adhere to each other and small particles are pulled out, leaving minute, shallow pits and powdery debris. Sometimes these surface conditions are neglected, but they are important in some application such as the aerospace industry. In this research work, non-contacting and contacting thermoelectric power techniques are performed in fretted 7075-T6 and Ti-6Al-4V samples. It has been found that the contacting and non-contacting thermoelectric power measurements are associated directly with the subtle material variations such as work hardening and residual stresses due to plastic deformation produced in the fretting zone but surface topography. Therefore, both techniques could be used for a global characterization of the most relevant fretting induced effects. Potential of these techniques to monitor subsurface changes in other severe surface plastic deformation processes are clearly envisaged.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Mechanical stress and fatigue analysis · Adhesion, Friction, and Surface Interactions · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. Shinde, S.R. and Hoeppner, D.W., Fretting fatigue behavior in 7075-T6 aluminum alloy, Wear, 2006, vol. 261, pp. 426–434.10.1016/j.wear.2005.12.015 ↗
2. Farrahi, G.H., Tirehdast, M., Masoumi Khalil Abad, E., Parsa, S., and Motakefpoor, M., Failure analysis of a gas turbine compressor, Eng. Fail. Analy, 2011, vol. 18, pp. 474–484.10.1016/j.engfailanal.2010.09.042 ↗
3. Hutson, A.L., Neslen, C., and Nicholas, T., Characterization of fretting fatigue crack initiation processes in CR Ti-6Al-4V, Wear, 2003, vol. 36, pp. 13–143.
4. Conner, B.P., Hutson, A.L., and Chambon, L., Observations of fretting fatigue micro-damage of Ti-6Al-4V, Wear, 2003, vol. 255, pp. 259–268.10.1016/S0043-1648(03)00152-2 ↗
5. Hutson, A., Sathish, S., and Nicholas, T., Progression of fretting damage in Ti-6Al-4V, Tribo. Int., 2006, vol. 39, pp. 1197–1205.10.1016/j.triboint.2006.02.009 ↗
6. Fouvry, S. and Kubiak, K., Introduction of a fretting-fatigue mapping concept: Development of a dual crack nucleation-crack propagation approach to formalize fretting-fatigue damage, Int. J. of Fatigue, 2009, vol. 31, pp. 250–262.10.1016/j.ijfatigue.2008.09.002 ↗
7. Pyzalla, A., Wang, L., Wild, E., and Wroblewski, T., Changes in microstructure, texture and residual stresses of a rail resulting from friction and wear, Wear, 2001, vol. 251, pp. 901–907.10.1016/S0043-1648(01)00748-7 ↗
8. Vadiraj, A., Kamaraj, M., Kamachi Mudali, U., and Nath, A.K., Effect of surface modified layers on fretting fatigue damage of biomedical titanium alloys, Mat. Sci. and Tech., 2006, vol. 22, pp. 1119–1125.10.1179/174328406X109212 ↗
9. Vadiraj, A. and Kamaraj, M., Fretting fatigue behavior of surface modified biomedical titanium alloys, Trans. Indian Inst. Met., 2010, vol. 63, pp. 217–223.10.1007/s12666-010-0030-0 ↗
10. Martinez, S.A., Sathish, S., Blodgett, M.B., and Mall, S., Residual stress relaxation due to fretting fatigue in shot peened surfaces of Ti-6Al-4V, in Review of Progress in Quantitative NDE, 2003, AIP 22, pp. 1531–1538.
11. Wagle, S. and Kato, H., Ultrasonic wave intensity reflected from fretting fatigue cracks at bolt joints of aluminum alloy plates, NDT and E Int., 2009, vol. 42, pp. 690–695.10.1016/j.ndteint.2009.06.002 ↗
12. Carreon, H., Nagy, P.B., and Blodgett, M.P., Thermoelectric nondestructive evaluation of residual stress in shot-peened metals, Res. Nondestr. Eval., 2002, vol. 14, pp. 59–80.10.1080/09349840209409705 ↗
13. Carreon, H. and Nagy, P.B., Detection of surface imperfections in metals by a noncontacting thermoelectric method, in 7th ASME NDE Topical Conference, 2000, vol. 20, pp. 209–215.
14. Lakshminayaran, B., Carreon, H., and Nagy, P.B., Monitoring of the level of residual stress in surface-treated specimens by a noncontacting thermoelectric technique, in Review of Progress in Quantitative NDE, 2003, AIP 22, pp. 1523–1530.
15. Carreon, H., Barriuso, S., Barrera, G., González, J.L., and Caballero, F.G., Assessment of blasting induced effects on medical 316 LVM stainless steel by contacting and non-contacting thermoelectric power techniques, Surf. and Coat. Tech., 2012, vol. 206, pp. 2942–2947.10.1016/j.surfcoat.2011.12.026 ↗
16. Carreon, H., Barriuso, S., Lieblich, M., González, J.L., Jimenez, J.A., and Caballero, F.G., Significance of the contacting and no contacting thermoelectric power measurements applied to grit blasted medical Ti6Al4V, Mater. Sci. Eng. C, 2013, vol. 33, pp. 1417–1422.10.1016/j.msec.2012.12.045 ↗
17. Caballero, F.G., Capdevila, C., Alvarez, L.F., and García de Andrés, C., Thermoelectric power studies on a martensitic stainless steel, Scr. Mater., 2004, vol. 50, pp. 1061–1066.10.1016/j.scriptamat.2003.12.017 ↗
18. Ferrer, J.P., Cock, T., Capdevila, C., Caballero, F.G., and Garcia, C., Comparison of the annealing behaviour between cold and warm rolled ELC steels by thermoelectric power measurements, Acta Mater., 2007, vol. 55, pp. 2075–2083.10.1016/j.actamat.2006.11.010 ↗
19. Kleber, X., Detection of surface and subsurface heterogeneities by the hot tip thermoelectric power method, NDT and E Int., 2008, vol. 41, pp. 364–370.10.1016/j.ndteint.2008.01.003 ↗
20. Carreon, H. and Medina, A., “Non-destructive characterization of the level of plastic deformation by thermoelectric power measurements in cold-rolled Ti-6Al-4V samples,” Nondestruct. Test. Eval., 2007, vol. 22, pp. 299–311.10.1080/10589750701546960 ↗
21. Morgner, W., Fundamentals of nondestructive materials characterization, NDT and E Int., 1994, vol. 27, pp. 263–268.10.1016/0963-8695(94)90131-7 ↗
22. Carreon, H., Thermoelectric detection of the magnetic field by fluxgate gradiometer on subsurface tin inclusions embedded in a copper bar, NDT and E Int., 2006, vol. 39, pp. 22–28.10.1016/j.ndteint.2005.05.002 ↗
23. Yu, F., Detection of rectangular tin inclusion in copper using laser-based self-referencing thermoelectric technique, NDT and E Int., 2010, vol. 43, pp. 182–189.10.1016/j.ndteint.2009.11.001 ↗
24. Carreon, H., On the exploitation of thermoelectric coupling for characterization of elliptical inclusions in metals, Exp. Therm. and Fluid Sci., 2013, vol. 44:1, pp. 673–679.10.1016/j.expthermflusci.2012.09.007 ↗
25. Carreon, H., Thermoelectric detection of hard alpha inclusion in Ti-6Al-4V by magnetic sensing, J. Alloys Compd., 2007, vol. 427, pp. 183–189.10.1016/j.jallcom.2006.03.004 ↗
26. Carreon, H., Fretting damage assessment in Ti-6Al-4 V by magnetic sensing, Wear, 2008, vol. 465, pp. 255–260.10.1016/j.wear.2007.10.005 ↗
27. Debarberis, L., Acosta, B., Sevini, F., Pirfo, S., Hyde, J.M., Hutchings, M.T., and Ortner, S., Studies of radiation embrittlement of model alloys by positron annihilation, thermoelectric and magnetic measurements, NDT and E Int., 2004, vol. 37, pp. 19–22.10.1016/S0963-8695(03)00069-0 ↗