Analytical bond behavior of cold drawn SMA crimped fibers considering embedded length and fiber wave depth
Source abstract
Abstract
Abstract The NiTi SMA fibers were cold drawn to introduce prestrain, and then, they were made to crimped fibers with various wave depths. The recovery stress was measured, which was useful for closing the cracks in fiber-reinforced concrete. The pullout behaviors were also examined considering the existing recovery stress, and it is found that the recovery stress did not influence so much on the pullout behavior. According to the pullout results, a parametric study used a finite element analyzing (FEA) model to quantify the cohesive surface model’s parameters and the value of the friction coefficient. Then, the developed model is used to investigate the crimped fiber’s pullout behavior with various embedded lengths and wave depths. When the fiber in the elastic range, the peak stresses significantly raise due to increasing embedded waves; they show a linear relationship. After the yield of the SMA fiber, the peak stresses are also a function of embedded waves; however, the increasing trend is slow down. Concerning the cost, the even distribution of the fiber, and for guaranteeing the fiber experiences the pulling out, it is recommended that the embedded lengths and corresponding wave depths should be designed to avoid the yield.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Innovations in Concrete and Construction Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Civil and Environmental Engineering, Hongik University , Seoul 04066 , Republic of Korea
References (50)
Show source-provided references
1. Han, J., D. Wang, and P. Zhang. Effect of nano and micro conductive materials on conductive properties of carbon fiber reinforced concrete. Nanotechnology Reviews, Vol. 9, No. 1, 2020, pp. 445–454.10.1515/ntrev-2020-0034 ↗
2. Lapčík, L., M. Vašina, B. Lapčíková, M. Staněk, M. Ovsík, and Y. Murtaja. Study of the material engineering properties of high-density poly (ethylene)/perlite nanocomposite materials. Nanotechnology Reviews, Vol. 9, No. 1, 2020, pp. 1491–1499.10.1515/ntrev-2020-0113 ↗
3. Gao, D., L. Zhao, and G. Chen. Flexural behavior of fiber and nanoparticle reinforced concrete at high temperatures. Fire and Materials, Vol. 42, No. 7, 2018, pp. 725–740.10.1002/fam.2526 ↗
4. Vahidi Pashaki, P., M. Pouya, and V. A. Maleki. High-speed cryogenic machining of the carbon nanotube reinforced nanocomposites: Finite element analysis and simulation. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Vol. 232, No. 11, 2018, pp. 1927–1936.10.1177/0954406217714012 ↗
5. Yuan, G., Y. Bai, Z. Jia, D. Hui, and K. T. Lau. Enhancement of interfacial bonding strength of SMA smart composites by using mechanical indented method. Composites Part B: Engineering, Vol. 106, 2016, pp. 99–106.10.1016/j.compositesb.2016.08.033 ↗
6. Hu, H., P. Papastergiou, H. Angelakopoulos, M. Guadagnini, and K. Pilakoutas. Mechanical properties of SFRC using blended manufactured and recycled tyre steel fibres. Construction and Building Materials, Vol. 163, 2018, pp. 376–389.10.1016/j.conbuildmat.2017.12.116 ↗
7. Rahmani, T., B. Kiani, M. Shekarchi, and A. Safari. Statistical and experimental analysis on the behavior of fiber reinforced concretes subjected to drop weight test. Construction and Building Materials, Vol. 37, 2012, pp. 360–369.10.1016/j.conbuildmat.2012.07.068 ↗
8. Nili, M. and V. Afroughsabet. Combined effect of silica fume and steel fibers on the impact resistance and mechanical properties of concrete. International Journal of Impact Engineering, Vol. 37, No. 8, 2010, pp. 879–886.10.1016/j.ijimpeng.2010.03.004 ↗
9. Jonnalagadda, K., G. E. Kline, and N. R. Sottos. Local displacements and load transfer in shape memory alloy composites. Experimental Mechanics, Vol. 37, No. 1, 1997, pp. 78–86.10.1007/BF02328753 ↗
10. Payandeh, Y., F. Meraghni, E. Patoor, and A. Eberhardt. Debonding initiation in a NiTi shape memory wire–epoxy matrix composite. Influence of martensitic transformation. Materials & Design, Vol. 31, No. 3, 2010, pp. 1077–1084.10.1016/j.matdes.2009.09.048 ↗
11. Poon, C. K., L. M. Zhou, W. Jin, and S. Q. Shi. Interfacial debond of shape memory alloy composites. Smart Materials and Structures, Vol. 14, No. 4, 2005, id. N29.10.1088/0964-1726/14/4/N05 ↗
12. Cai, S., C. Wu, W. Yang, W. Liang, H. Yu, and L. Liu. Recent advance in surface modification for regulating cell adhesion and behaviors. Nanotechnology Reviews, Vol. 9, No. 1, 2020, pp. 971–989.10.1515/ntrev-2020-0076 ↗
13. Jang, B. K. and T. Kishi. Adhesive strength between TiNi fibers embedded in CFRP composites. Materials Letters, Vol. 59, No. 11, 2005, pp. 1338–1341.10.1016/j.matlet.2005.01.006 ↗
14. Gebuhr, G., M. Pise, M. Sarhil, S. Anders, D. Brands, and J. Schröder. Analysis and evaluation of the pull‐out behavior of hooked steel fibers embedded in high and ultra‐high-performance concrete for calibration of numerical models. Structural Concrete, Vol. 20, No. 4, 2019, pp. 1254–1264.10.1002/suco.201900034 ↗
15. Maleki, V. A. and N. Mohammadi. Buckling analysis of cracked functionally graded material column with piezoelectric patches. Smart Materials and Structures, Vol. 26, No. 3, 2017, id. 035031.10.1088/1361-665X/aa5324 ↗
16. Liu, J., N. Farzadnia, and C. Shi. Effects of superabsorbent polymer on interfacial transition zone and mechanical properties of ultra-high-performance concrete. Construction and Building Materials, Vol. 231, 2020, id. 117142.10.1016/j.conbuildmat.2019.117142 ↗
17. Guo, Z., Q. Zhu, W. Wu, and Y. Chen. Research on bond–slip performance between pultruded glass fiber-reinforced polymer tube and nano-CaCO3 concrete. Nanotechnology Reviews, Vol. 9, No. 1, 2020, pp. 637–649.10.1515/ntrev-2020-0036 ↗
18. Jung, C. Y. and J. H. Lee. Crack closure and flexural tensile capacity with SMA fibers randomly embedded on tensile side of mortar beams. Nanotechnology Reviews, Vol. 9, No. 1, 2020, pp. 354–366.10.1515/ntrev-2020-0026 ↗
19. Alhijazi, M., Q. Zeeshan, Z. Qin, B. Safaei, and M. Asmael. Finite element analysis of natural fibers composites: A review. Nanotechnology Reviews, Vol. 9, No. 1, 2020, pp. 853–875.10.1515/ntrev-2020-0069 ↗
20. Lei, M., Z. Chen, H. Lu, and K. Yu. Recent progress in shape memory polymer composites: methods, properties, applications and prospects. Nanotechnology Reviews, Vol. 8, No. 1, 2019, pp. 327–351.10.1515/ntrev-2019-0031 ↗
21. Maage, M. Interaction between steel fibers and cement-based matrixes. Matériaux et Construction, Vol. 10, No. 5, 1977, pp. 297–301.10.1007/BF02478831 ↗
22. Naaman, A. E., G. G. Namur, J. M. Alwan, and H. S. Najm. Fiber pullout and bond slip. II: Experimental validation. Journal of Structural Engineering, Vol. 117, No. 9, 1991, pp. 2791–2800.10.1061/(ASCE)0733-9445(1991)117:9(2791) ↗
23. Alwan, J. M., A. E. Naaman, and P. Guerrero. Effect of mechanical clamping on the pull-out response of hooked steel fibers embedded in cementitious matrices. Concrete Science and Engineering, Vol. 1, No. 1, 1999, pp. 15–25.
24. Chanvillard, G. Modeling the pullout of wire-drawn steel fibers. Cement and Concrete Research, Vol. 29, No. 7, 1999, pp. 1027–1037.10.1016/S0008-8846(99)00081-2 ↗
25. Laranjeira, F., C. Molins, and A. Aguado. Predicting the pullout response of inclined hooked steel fibers. Cement and concrete research, Vol. 40, No. 10, 2010, pp. 1471–1487.10.1016/j.cemconres.2010.05.005 ↗
26. Soetens, T., A. Van Gysel, S. Matthys, and L. Taerwe. A semi-analytical model to predict the pull-out behaviour of inclined hooked-end steel fibres. Construction and Building Materials, Vol. 43, 2013, pp. 253–265.10.1016/j.conbuildmat.2013.01.034 ↗
27. van der Aa, P. J. Biaxial stresses in steel fibre reinforced concrete modelling the pull out-behaviour of a single steel fibre using FEM. Faculty of architecture building and planning unit structural desing concretete structures, Einhoven University of Technology, Eindhoven, The Netherlands, 2014.
28. Yoo, D. Y. and S. Kim. Comparative pullout behavior of half-hooked and commercial steel fibers embedded in UHPC under static and impact loads. Cement and Concrete Composites, Vol. 97, 2019, pp. 89–106.10.1016/j.cemconcomp.2018.12.023 ↗
29. Ellis, B. D., D. L. McDowell, and M. Zhou. Simulation of single fiber pullout response with account of fiber morphology. Cement and Concrete Composites, Vol. 48, 2014, pp. 42–52.10.1016/j.cemconcomp.2014.01.003 ↗
30. Cunha, V. M., J. A. Barros, and J. M. Sena-Cruz. Pullout behavior of steel fibers in self-compacting concrete. Journal of Materials in Civil Engineering, Vol. 22, No. 1, 2010, pp. 1–9.10.1061/(ASCE)MT.1943-5533.0000001 ↗
31. Abdallah, S. and D. W. Rees. Comparisons between pull-out behaviour of various hooked-end fibres in normal–high strength concretes. International Journal of Concrete Structures and Materials, Vol. 13, No. 1, 2019, id. 27.10.1186/s40069-019-0337-0 ↗
32. Choi, E., D. J. Kim, Y. S. Chung, H. S. Kim, and C. Jung. Crack-closing of cement mortar beams using NiTi cold-drawn SMA short fibers. Smart Materials and Structures, Vol. 24, No. 1, 2014, id. 015018.10.1088/0964-1726/24/1/015018 ↗
33. Lee, K. J., J. H. Lee, C. Y. Jung, and E. Choi. Crack-closing performance of NiTi and NiTiNb fibers in cement mortar beams using shape memory effects. Composite Structures, Vol. 202, 2018, pp. 710–718.10.1016/j.compstruct.2018.03.080 ↗
34. Moser, K., A. Bergamini, R. Christen, and C. Czaderski. Feasibility of concrete prestressed by shape memory alloy short fibers. Materials and Structures, Vol. 38, No. 5, 2005, pp. 593–600.10.1007/BF02479551 ↗
35. Choi, E., H. K. Hong, H. S. Kim, and Y. S. Chung. Hysteretic behavior of NiTi and NiTiNb SMA wires under recovery or pre-stressing stress. Journal of Alloys and Compounds, Vol. 577, 2013, pp. S444–S447.10.1016/j.jallcom.2012.02.037 ↗
36. Rojob, H. and R. El-Hacha. Self-prestressing using iron-based shape memory alloy for flexural strengthening of reinforced concrete beams. ACI Structural Journal, Vol. 114, No. 2, 2017, id. 523.10.14359/51689455 ↗
37. Choi, E., D. J. Kim, H. Youn, and T. H. Nam. Repairing cracks developed in mortar beams reinforced by cold-drawn NiTi or NiTiNb SMA fibers. Smart Materials and Structures, Vol. 24, No. 12, 2015, id. 125010.10.1088/0964-1726/24/12/125010 ↗
38. Choi, E., H. S. Kim, and T. H. Nam. Effect of crimped SMA fiber geometry on recovery stress and pullout resistance. Composite Structures, 2020, id. 112466.10.1016/j.compstruct.2020.112466 ↗
39. Choi, E., H. V. Ho, and J. S. Jeon. Active reinforcing fiber of cementitious materials using crimped NiTi SMA fiber for crack-bridging and pullout resistance. Materials, Vol. 13, No. 17, 2020, id. 3845.10.3390/ma13173845 ↗
40. Dawood, M., M. W. El-Tahan, and B. Zheng. Bond behavior of superelastic shape memory alloys to carbon fiber reinforced polymer composites. Composites Part B: Engineering, Vol. 77, 2015, pp. 238–247.10.1016/j.compositesb.2015.03.043 ↗
41. El‐Tahan, M. and M. Dawood. Bond behavior of NiTiNb SMA wires embedded in CFRP composites. Polymer Composites, Vol. 39, No. 10, 2018, pp. 3780–3791.10.1002/pc.24408 ↗
42. Choi, E., B. Mohammadzadeh, D. Kim, and J. S. Jeon. A new experimental investigation into the effects of reinforcing mortar beams with superelastic SMA fibers on controlling and closing cracks. Composites Part B: Engineering, Vol. 137, 2018, pp. 140–152.10.1016/j.compositesb.2017.11.017 ↗
43. Choi, E., D. Kim, J. H. Lee, and G. S. Ryu. Monotonic and hysteretic pullout behavior of superelastic SMA fibers with different anchorages. Composites Part B: Engineering, Vol. 108, 2017, pp. 232–242.10.1016/j.compositesb.2016.09.080 ↗
44. American Concrete Institute. Building Code Requirements for Structural Concrete (ACI 318-14) and Commentary, American Concrete Institute, Farmington Hills, MI, USA, 2014.
45. Abrams, D. A. Tests of bond between concrete and steel, University of Illinois at Urbana Champaign, College of Engineering, Engineering Experiment Station, Champaign, USA, 1913.
46. Hibbett, Karlsson, Sorensen. ABAQUS/standard: User’s Manual, Vol. 1, Hibbitt, Karlsson & Sorensen, Rhode Island, USA, 1998.
47. Blau, P. J. The significance and use of the friction coefficient. Tribology International, Vol. 34, No. 9, 2001, pp. 585–591.10.1016/S0301-679X(01)00050-0 ↗
48. Rabbat, B. G. and H. G. Russell. Friction coefficient of steel on concrete or grout. Journal of Structural Engineering, Vol. 111, No. 3, 1985, pp. 505–515.10.1061/(ASCE)0733-9445(1985)111:3(505) ↗
49. Yazıcı, Ş., G. İnan, and V. Tabak. Effect of aspect ratio and volume fraction of steel fiber on the mechanical properties of SFRC. Construction and Building Materials, Vol. 21, No. 6, 2007, pp. 1250–1253.10.1016/j.conbuildmat.2006.05.025 ↗
50. Choi, E., A. Ostadrahimi, and J. H. Lee. Pullout resistance of crimped reinforcing fibers using cold-drawn NiTi SMA wires. Construction and Building Materials, Vol. 265, 2020, id. 120858.10.1016/j.conbuildmat.2020.120858 ↗