Structural aspects of strength and methods to increase the serviceability of carbide coatings
Source abstract
Abstract
The effect of composition and structure on the microhardness, plasticity parameter (δH) and fracture toughness (KIc) of the widely used carbide layers (TiC, ZrC, VC, NbC, Cr23C6, Cr7C3) was investigated. It was found that the microhardness and plasticity parameter were basically determined by the composition of the carbide coatings and did not substantially vary with the structure, which had a preferential effect on fracture toughness. The laws governing the influence of grain shape, size, and preferred orientation on the fracture toughness of the coatings were determined. Recommendations for the control of composition and structure were formulated, and methods developed for the deposition of carbide coatings which increased the durability of a hard-alloy tool used under severe conditions two-fold compared to the best known analogues.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced materials and composites · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. A. V. Byakova, “Determination of microhardness for evaluation of the structural strength of coatings,”Probl. Prochn., No. 9, 44–54 (1995).
2. A. V. Byakova and V. G. Gorbach, “Fracture resistance and evaluation of the brittle strength of coatings with an initial field of residual stresses,”Probl. Prochn., No. 1, 51–61 (1994).
3. A. A. Babad-Zakhryapin and G. D. Kuznetsov,Textured High-Temperature Coatings [in Russian], Atomizdat, Moscow (1980).
4. M. M. Borodkina and É. N. Spector,X-Ray Diffraction Analysis of Textures in Metals and Alloys [in Russian], Metallurgiya, Moscow (1981).
5. Yu. V. Milman, V. A. Galanov, and S. I. Chugunova, “Plasticity characteristic obtained through hardness measurement,”Acta Metall. Mater.,41, No. 9, 2523–2532 (1993).10.1016/0956-7151(93)90122-9 ↗
6. A. G. Evans and E. A. Charles, “Fracture toughness determination buy indentation,”J. Amer. Ceram. Soc.,59, No. 7/8, 371–372 (1976).10.1111/j.1151-2916.1976.tb10991.x ↗
7. K. Niihara, R. Morena, and D. P. Hasselman, “Evaluation ofK Ic of brittle solids by the indentation method with low crack-to-indent ratios,”J. Mat. Sci. Let.,1, No. 1, 13–16 (1981).10.1007/BF00724706 ↗
8. I. N. Frantsevich, F. F. Voronov, and S. A. Bakuta,Elastic Constants and Elastic Moduli of Metals and Nonmetals. Handbook [in Russian], I. N. Frantsevich (ed.), Nauk, Dumka, Kiev (1982).
9. A. V. Byakova, V. S. Loskutov, and G. I. Pal’shin, “Structure and composition of carbide coatings,”Visn. Akad. Nauk. URSR, No. 8, 41–49 (1983).
10. V. V. Gridnev, V. I. Trefilov, S. A. Firstov, et al.,Phase and Structure Transformations, and Metastable States in Metals [in Russian], Nauk, Dumka, Kiev (1988).
11. A. Evans, A. Hure, and D. Porter,Crack Resistance of Ceramics [Russian translation], Mir, Moscow (1979), Vol.17, pp. 134–154.
12. A. V. Byakova, “Effect of the structure state of titanium nitride coatings on their strength,”Sverkhtverd. Mater., No. 5, 30–37 (1992).
13. J. J. Gilman, “Cleavage, plasticity, and viscosity of crystals,” in:Atomic Mechanisms of Fracture [in Russian], Metallurgiya, Moscow (1963), pp. 220–249.