Permeability of Short Fiber Reinforced Powder Metallurgy Material and its Application in Porous Mold
Source abstract
Abstract
Permeability is one of the key properties for understanding the fluid flow and pressure drop in porous metal. In this study, a novel 304 stainless steel fiber reinforced powder metallurgy (P/M) material is produced. Stainless steel powders and short fibers are alternately laid in layers according to mass fraction and then sintered to produce the porous material. Air and water permeability tests are conducted to characterize the permeability of the material. The powder mesh, porosity, and pore size are varied to investigate the effect of permeability. Porous molds made of the material are designed to perform paperboard molding and plastic-injection experiments. The results demonstrate that the relationship between pressure drop per unit length and flow velocity is a parabola, where air or water flows through the P/M material. The permeability coefficient decreases with increasing powder mesh. Compared to water going through the material, the permeability coefficient is higher and the inertial loss is more significant in case of air. The pore size has greater effect on the permeability, than porosity. The perfect appearance of the paperboard presents a good permeability of the P/M material, showing the promising application in molding.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Heat and Mass Transfer in Porous Media · Polymer Foaming and Composites · Injection Molding Process and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. L. P. Lefebvre, J. Banhart, and D. C. Dunand, “Porous metals and metallic foams: Current status and recent developments,” Adv. Eng. Mater., 10, No. 9, 775–787 (2008).10.1002/adem.200800241 ↗
2. Z. Xi, J. Zhu, H. Tang, et al, “Progress of application researches of porous fiber metals,” Materials, 4, No. 4, 816–824 (2011).10.3390/ma4040816 ↗
3. A. Nabovati, E. W. Llewellin, and A. C. M. Sousa, “A general model for the permeability of fibrous porous media based on fluid flow simulations using the lattice Boltzmann method,” Compos. Pt. A, 40, Nos. 6–7, 860–869 (2009).10.1016/j.compositesa.2009.04.009 ↗
4. J. K. Kuo and C. K. Chen, “A novel Nylon-6–S316L fiber compound material for injection molded PEM fuel cell bipolar plates,” J. Power Sources, 162, No. 1, 207–214 (2006).10.1016/j.jpowsour.2006.06.034 ↗
5. B. Zhang and T. Chen, “Calculation of sound absorption characteristics of porous sintered fiber metal,” Appl. Acoust., 70, No. 2, 337–346 (2009).10.1016/j.apacoust.2008.03.004 ↗
6. A. S. Abduljalil, Z. Yu, and A. J. Jaworski, “Selection and experimental evaluation of low-cost porous materials for regenerator applications in thermoacoustic engines,” Mater. Des., 32, No. 1, 217–228 (2011).10.1016/j.matdes.2010.06.012 ↗
7. C. P. Chen, M. T. Chuang, Y. H. Hsiao, et al., “Simulation and experimental study in determining injection molding process parameters for thin-shell plastic parts via design of experiments analysis,” Expert Syst. Appl., 36, No. 7, 10752–10759 (2009).10.1016/j.eswa.2009.02.017 ↗
8. S. W. Kim and L. S. Turng, “Developments of three-dimensional computer-aided engineering simulation for injection moulding,” Model. Simul. Mater. Sc. Eng., 12, No. 3, S151–S173 (2004).10.1088/0965-0393/12/3/S07 ↗
9. M. C. Yu, W. B. Young, and P. M. Hsu, “Micro-injection molding with the infrared assisted mold heating system,” Mater. Sci. Eng. A, 460–461, 288–295 (2007).10.1016/j.msea.2007.02.036 ↗
10. Z. Zhou, W. Cao, Z. Wu, et al., “Permeable steel and its application in plastic-injection mould,” Chin. J. Mech. Eng., 23, 312–316 (2010).10.3901/CJME.2010.03.312 ↗
11. C. Y. Chang, S. Y. Yang, L. S. Huang, et al., “Fabrication of plastic microlens array using gas-assisted micro-hot-embossing with a silicon mold,” Infrared Phys. Technol., 48, No. 2, 163–173 (2006).10.1016/j.infrared.2005.10.002 ↗
12. J. H. Chang and S. Y. Yang, “Gas pressurized hot embossing for transcription of micro-features,” Microsyst. Technol., 10, No. 1, 76–80 (2003).10.1007/s00542-003-0311-1 ↗
13. N. Kurgan, “Effect of porosity and density on the mechanical and microstructural properties of sintered 316L stainless steel implant materials,” Mater. Des., 55, 235–241 (2014).10.1016/j.matdes.2013.09.058 ↗
14. A. E. Markaki, V. Gergely, A. Cockburn, et al., “Production of a highly porous material by liquid phase sintering of short ferritic stainless steel fibres and a preliminary study of its mechanical behaviour,” Compos. Sci. Technol., 63, No. 16, 2345–2351 (2003).10.1016/S0266-3538(03)00267-7 ↗
15. Y. Tang, W. Zhou, M. Pan, et al., “Porous copper fiber sintered felts: An innovative catalyst support of methanol steam reformer for hydrogen production,” Int. J. Hydrog. Energy, 33, No. 12, 2950–2956 (2008).10.1016/j.ijhydene.2008.04.006 ↗
16. N. Dukhan, Ö. Bagci, and M. Özdemir, “Experimental flow in various porous media and reconciliation of Forchheimer and Ergun relations,” Exp. Therm. Fluid Sci., 57, 425–433 (2014).10.1016/j.expthermflusci.2014.06.011 ↗
17. J. G. Mitchell, Mold with Porous Cavity Vent, Patent US 4165062 A, Appl. Jan. 13, 1978, Publ. Aug. 21, 1979.
18. P. E. Andres, Cooling and Counter-Pressure Method for Producing Plastic Parts by Injection, Patent US 6855288 B2, Appl. Jan 10, 2001, Publ. Feb. 15, 2005.
19. B. Yao, Z. Zhou, L. Duan, et al., “Compressibility of 304 stainless steel powder metallurgy materials reinforced with 304 short stainless steel fibers,” Materials, 9, No. 3, 161 (2016).10.3390/ma9030161 ↗
20. N. Dukhan and C. A. Minjeur, “A two-permeability approach for assessing flow properties in metal foam,” J. Porous Mater., 18, No. 4, 417–424 (2010).10.1007/s10934-010-9393-1 ↗
21. K. Boomsma and D. Poulikakos, “The effects of compression and pore size variations on the liquid flow characteristics in metal foams,” J. Fluids Eng., 124, No. 1, 263–272 (2002).10.1115/1.1429637 ↗
22. B. Bromley, V. Hessel, A. Renken, et al., “'Sandwich reactor for heterogeneous catalytic processes: N2O decomposition as a case study,” Chem. Eng. Technol., 31, No. 8, 1162–1169 (2008).10.1002/ceat.200800218 ↗
23. P. X. Jiang and X. C. Lu, “Numerical simulation of fluid flow and convection heat transfer in sintered porous plate channels,” Int. J. Heat Mass Transf., 49, Nos. 9–10, 1685–1695 (2006).10.1016/j.ijheatmasstransfer.2005.10.026 ↗
24. O. Rahli, L. Tadrist, M. Miscevic, et al., “Fluid flow through randomly packed monodisperse fibers: The Kozeny-Carman parameter analysis,” J. Fluids Eng., 119, No. 1, 188–192 (1997).10.1115/1.2819107 ↗
25. R. C. Givler and S. A. Altobelli, “A determination of the effective viscosity for the Brinkmann-Forchheimer flow model,” J. Fluid Mech., 258, 355–370 (2006).10.1017/S0022112094003368 ↗
26. B. V. Antohe, J. L. Lage, D. C. Price, et al., “Experimental determination of permeability and inertia coefficients of mechanically compressed aluminum porous matrices,” J. Fluids Eng., 119, No. 2, 404–412 (1997).10.1115/1.2819148 ↗
27. A. Bergmark and L. Alzati, “Fatigue crack path in Cu–Ni–Mo alloyed PM steel,” Fatigue Fract. Eng. Mater. Struct., 28, Nos. 1–2, 229–235 (2005).10.1111/j.1460-2695.2004.00841.x ↗
28. W. D. Wong-Ángel, L. Téllez-Jurado, J. F. Chávez-Alcalá, et al., “Effect of copper on the mechanical properties of alloys formed by powder metallurgy,” Mater. Des., 58, 12–18 (2014).10.1016/j.matdes.2014.02.002 ↗
29. A. Bhattacharya, V. V. Calmidi, and R. L. Mahajan, “Thermophysical properties of high porosity metal foam,” Int. J. Heat. Mass. Transf., 45, No. 5, 1017–1031 (2002).10.1016/S0017-9310(01)00220-4 ↗