Crack resistance of modern ceramics and ceramic composites. II. EF method
Source abstract
Abstract
The procedure and test results are for crack resistance are presented for various monolithic and composite oxide and nonoxide ceramics by chipping the rectangular edge of a polished specimen. The main difference of the test method suggested (EF method) with an arbitrary point of fracture for a specimen edge from the well-known similar method with a fixed point of fracture is demonstrated. Tests are performed with Rockwell, Vickers and Knoop indenters, and the Rockwell indenter is chosen as the optimum. On the basis of statistically reliable experimental data a direct relationship is established between edge toughness and critical fracture toughness determined in the same ceramic specimens based on scandium oxide, aluminum oxide, zirconium dioxide, silicon carbide and silicon nitride. The EF method, whose use does not require special equipment, may be used effectively in a normal metallurgy test laboratory, particularly when specimens for evaluating ceramic breaking resistance may only be prepared in smaller sizes than those required for standard crack resistance tests.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (23)
Show source-provided references
1. G. A. Gogotsi, “Crack resistance of contemporary ceramics and ceramic composites. I. SEVNB method, ” Poroshk. Metall., Nos. 7–8, 54–67 (2004).10.1023/B:PMMC.0000048131.10524.42 ↗
2. CEN/TS 14425-5:2004, Advanced Technical ceramics-Test Methods for Determination of Fracture Toughness of Monolithic Ceramics, Part 5, Single-edge V-notch Beam (SEVNB) Method, CEN, Brussels (2004).
3. D. J. Roweliffe, “Indentation of ceramics,” in: Introduction to Mechanical Behavior of Ceramics, IRTEC, Faenza (1992).
4. G. D. Quinn, J. A. Salem, I. Bar-On, and M. G. Kjenkins, “The new ASTM fracture toughness of advance ceramics standard,” Ceram. Eng. Sci. Proc., No. 3, 565–579 (1998).
5. H. Fischer and R. Marx, “Fracture toughness of dental ceramics: comparison of bending and indentation method,” Dental Materials, No. 1, 112–119 (2002).10.1016/S0109-5641(01)00005-7 ↗
6. G. A. Gogotsi, S. P. Mudrik, and A. Rendtel, “Sensitivity of silicon carbide and other ceramics to edge fracture: Method and results,” 28th Internat. Conf. Advan. Ceram. Compos., E. Lara-Cuzio and M. Readey (eds.), 25, 156–163.
7. T. L. Anderson, Fracture Mechanics: Fundamentals and Application, CRC Press (1995).
8. E. Almond and N. McCormick, “Constant geometry edge flaking of brittle materials,” Nature, 321, 53–55 (1986).10.1038/321053a0 ↗
9. N. McCormick and E. Almond, “Edge flaking of brittle materials,” J. Hard Mater., 1, No. 1, 25–51 (1990).
10. R. Morrell and A. Grant, “Edge chipping — what does it tell us?,” in: Fractography of Glass and Ceramics IV, J. R. Varuer and G. D. Quinn (eds.), Amer. Ceram. Soc., Westerville (2001).
11. M. Hang, R. Dabnzer, and R. Paar, “Edge toughness of brittle materials,” Engineering Ceramics’96: Higher Reliability Through Processing, G. N. Rabini, M. Haviar, and P. Saigalik (eds.), Kluwer Acad. Publ. (1997).10.1007/978-94-011-5798-8_26 ↗
12. J. Quinn and I. Lloyd, “Flake and scratch size ratios in ceramics,” in: Fractography of Glass and Ceramics IV, J. R. Varuer and G. D. Quinn (eds.), Amer. Ceram. Soc., Westerville (2001).
13. F. Petit, P. Descamps, J. P. Erauw, and F. Cambier, “Toughness (K Ic) measurement by a sliding indentation method,” Key Eng. Mater., 206–213, 629–632 (1992).
14. G. R. Anstis, P. Chantikul, B. R. Lawn, and D. B. Marshall, “A critical evaluation technique for measuring fracture toughness. I. Direct crack measurements,” J. Amer. Ceram. Soc., 64, No. 9, 533–538 (1981).10.1111/j.1151-2916.1981.tb10320.x ↗
15. J. Kubler, “Fracture toughness of ceramics using the SEVNB method; round robin,” VAMAS, Report No. 37, ESIS Document D2-99, Swiss Federal Laboratories for Materials Testing and Research, Dubendorf (1999).
16. G. A. Gogotsi, “Deformation behavior of ceramics,” J. Eur. Ceram. Soc., No. 2, 87–92 (1991).10.1016/0955-2219(91)90005-K ↗
17. G. Gogotsi, S. Mudrik, and J. Quinn, “Crack resistance of silicon nitride ceramic edge: procedure and results,” Internat. Conf. “New Technology in Powder Metallurgy and Ceramics,” Proc. (Kiev, Ukraine, 2003), Institute for Problems of Materials Science, National Academy of Sciences of Ukraine, Kiev (2003), pp. 375–376.
18. G. A. Gogotsi and S. P. Mudrik, “Crack resistance of ceramics with specimen edge chipping (EF method),” Probl. Prochn., Nos. 5–6, 133–137 (2004).10.1023/B:STOM.0000048406.95349.ca ↗
19. M. Sh. Stepanov, Statistical Methods for Processing the Results of Mechanical Tests [in Russian], Mashinostroenie, Moscow (1985).
20. G. Gogotsi, “Thermal stress bahavior of yttria, scandia, and AlN ceramics,” Ceram. Int., No. 1, 31–35 (1980).10.1016/0390-5519(80)90030-7 ↗
21. G. A. Gogotsi, “Fracture toughness studies on ceramics and ceramic particulate composites at different temperature,” in: Fracture Resistance and Testing of Monolithic and Composite Brittle Materials, ASTM STP 1409, J. A. Salem, G. D. Quinn, and M. G. Jenkins (eds.), American Soc. for Testing and Materials, Pennsylvania (2002).
22. G. Gogotsi, M. Lugovoy, V. Slyunyayev, and M. Orlovskaya, “Development of multilayer Si3N4 base ceramic composites having an ability to arrest cracks,” Abstr. 2nd Perspective Mater. of Functional and Structural Purposes: Possibilities of Obtaining New Level of Properties, Kiev (2002).
23. K. Kleveland, N. Orlovskaya, T. Gtrande, “Ferroelastic behavior of LaCoO3-based ceramics, ” J. Amer. Ceram. Soc., 84, No. 9, 2029–2033 (2001).10.1111/j.1151-2916.2001.tb00953.x ↗