journal article·2020-09

Mechanical Properties of Microlayered Ti–Al Materials in Static and Cyclic Loading

Yu.F. Lugovskoi, V.A. Nazarenko, N.V. Minakov, S.A. Spiridonov, V.N. Nischenets

Powder Metallurgy and Metal Ceramics· Volume 59· Issue 5-6
Publisher page

Abstract

The technique for producing microlayered materials by sintering and rolling a package of alternating titanium and aluminum ribbons at 460 and 770°C is presented. The initial package thickness was 2.6 mm and the final thickness after hot rolling was 1.8 mm. Then the preform was rolled at room temperature to a thickness of 0.5 mm. The total strain at 20°C was e = ln1.8/0.5 = 1.3. Some ribbons 0.5 mm thick stratified in the middle and were tested by static and cyclic bending. X-ray diffraction found that the material that was heated and rolled at 770°C contained an hcp titanium phase and a TiAl3 phase. Structural anisotropy in titanium layers was established. The proportional limit of the 0.5 mm thick material was 368 MPa. The elastic characteristics, transmission energy of vibrations, and fatigue strength of the microlayered Ti–TiAl3 samples 0.25 mm thick cut along and across the rolling direction were determined. For this purpose, firstand second-mode resonant bending vibrations of cantilevered samples were excited and dependences of the maximum stresses in the samples on machine (electrodynamic shaker) power, W/Wmax, were found. The destructive fatigue stresses in the samples versus the number of load cycles were determined as well. Young’s modulus of the samples cut out along the rolling direction was 92 and for the samples cut out across the rolling direction was 100 GPa. The microlayered Ti–TiAl3 material along the rolling direction is less perfect than that across the rolling direction since nondestructive stresses are 11% lower along the rolling direction because of greater energy dissipation in anisotropic crystallographic structure, the relative excitation power of vibrations being the same. The ultimate strength determined from 107 cycles (Troll = 460°C) was 303 MPa for the Ti–Al samples along the rolling direction and 299 MPa for the Ti–TiAl3 samples along the rolling direction and 481 MPa for those across the rolling direction.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · Aluminum Alloys Composites Properties · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. B.A. Movchan, S.A. Firstov, and Yu.F. Lugovskoi, Structure, Strength, and Fatigue Resistance of Microcrystalline and Microlayered Materials [in Russian], Naukova Dumka, Kyiv (2015), p. 171.
2. S.A. Firstov and Yu.F. Lugovskoi, “Effect of microstructures on the cyclic fatigue life of microlayered Fe/Cu, Mo/Cu, and precipitation-hardened Ni–Cr–Al2O3 materials,” Dop. Nats. Akad. Nauk Ukrainy, No. 10, 112–117 (2008).
3. K.A. Gogaev, V.S. Voropaev, Yu.N. Podrezov, Yu.F. Lugovskoi, V.A. Nazarenko, A.Yu. Koval, and Ya.I. Evich, “Mechanical and fatigue properties of powder titanium strips obtained by asymmetric rolling,” Powder Metall. Mer. Ceram., 56, No. 1–2, 53–59 (2017).10.1007/s11106-017-9871-y ↗
4. Yu.F. Lugovskoi, Yu.N. Podrezov, V.A. Nazarenko, D.G. Verbilo, and A.Yu. Koval, “Mechanical properties and fracture mechanisms of commercially pure multilayer iron produced by strip joint rolling,” Powder Metall. Met. Ceram., 56, No. 5–6, 245–252 (2017).10.1007/s11106-017-9892-6 ↗
5. V.I. Ivanov and K.K. Yasinskii, “Effectiveness of high-temperature creep-resistant alloys produced from intermetallic Ti3Al and TiAl for operation at 600–800°C in aerospace engineering,” Tekhnol. Legk. Splav., No. 3, 63–68 (1996).
6. G. Henaff and A.L. Gloanec, “Fatigue properties of TiAl alloys,” Intermetallics, 13, 543–558 (2005).10.1016/j.intermet.2004.09.007 ↗
7. T.E.J. Edwards, “Recent progress in the high-cycle fatigue behavior of γ-TiAl alloys,” Mater. Sci. Technol., 34, No. 16, 1919–1939 (2018).10.1080/02670836.2018.1463614 ↗
8. S.G. Grigorenko, G.M. Grigorenko, and O.M. Zadorozhnyuk, “Titanium intermetallics. Features, properties, and applications (overview),” Sovr. Elektrometall., No. 3 (128), 51–58 (2017).10.15407/sem2017.03.08 ↗
9. A.V. Korzh, Yu.F. Lugovskoi, and A.V. Vdovichenko, “Statistical and dynamic properties of quasimicrolayered condensed Ti/Ti3Al materials,” in: Current Problems of Materials Science [in Russian], Inst. Probl. Materialoved. Akad. Nauk Ukrainy, Kyiv (1991), pp. 75–80.
10. S.A. Zelepugin, R.A. Shkoda, O.K. Lepakova, A.S. Zelepugin, N.G. Kasatski, A.A. Shavnev, and E.I. Krasnov, “Synthesis of metallic/intermetallic layered Ti–TiAl3 composite with different methods,” Tr. Vseross. Inst. Aviats. Mater., No. 11 (47), 23–31 (2014).
11. K.A. Gogaev, V.A. Nazarenko, and Yu.G. Lugovskoi, “Method of producing metallic laminate preforms,” Ukrainian Utility Patent No. 107192, reg. May 25, 2016; Bulletin No. 10.
12. V.T. Witusiewicz, A.A. Bondar, U. Hecht, S. Rex, and T.Y. Velikanova, “The Al-B-Nb-Ti system. III. Thermodynamic re-evaluation of the constituent binary system Al-Ti,” J. Alloys Compd., 465, 64-77 (2008).10.1016/j.jallcom.2007.10.061 ↗
13. K.Yu. Yakovchuk, A.V. Mikitchik, Yu.E. Rudoi, and Yu.F. Lugovskoi, “Effect of condensed multilayer protective coatings on the fatigue resistance of VT6 hardmetal samples,” Sovr. Elektrometall., No. 3, 45–53 (2019).10.15407/sem2019.03.07 ↗
14. V.A. Kuzmenko, Sound and Ultrasound Vibrations of Materials in Dynamic Testing [in Russian], Izd. Akad. Nauk USSR, Kyiv (1963), p. 152.
15. Yu.F. Lugovskoi, “Method for bending fatigue tests of composites produced by electron-beam evaporation,” Probl. Spets. Elektrometall., No. 4, 61–65 (1987).
16. W.A. Dollase, “Correction of intensities for preferred orientation in powder diffractometry: Application of the March model,” J. Appl. Crystallogr., 15, 267–272 (1986).
17. Yu.F. Lugovskoi, V.A. Nazarenko, V.N. Nishchenets, and S.A. Spiridonov, “Properties of rolled multilayered titanium under cyclic loading,” in: 7th Int. Conf. Deformation and Fracture of Materials and Nanomaterials [in Russian] (November 7–10, 2017, Moscow), Inst. Metall. RAN, Moscow (2017), pp. 346–347.
18. V.F. Terentiev, “Cyclic strength of submicrocrystalline and nanocrystalline metals and alloys (overview),” Nov. Mater. Tekhnol. Metall. Mashynobud., No. 1, 8–24 (2010).