The Structure and Properties of the Molybdenum-Doped WC–W2C Eutectic Alloy Depending on the Production Method
Source abstract
Abstract
Scanning and transmission electron microscopy and X-ray diffraction have revealed that the eutectic 5 wt.% Mo-doped WC–W2C alloy changes its cooling rate in the melt crystallization process when produced in the Tammann furnace, by electron-beam evaporation, and by centrifugal sputtering. This increases the size of phase components by a factor of 2 to 2.5, decreases the number of phases, and reduces compressive stresses (in the W2C matrix) and tensile stresses (in the WC, Mo2C, and (W, Mo)2C inclusions) to 50% and more. These changes result in one and a half times higher hardness and two times higher strength of doped relit, which is widely used for surfacing machine parts and mechanisms operating in conditions of abrasive wear and high dynamic loads.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Metal Alloys Wear and Properties · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (11)
Show source-provided references
1. S. Rickard, Effect of Tungsten Carbides Properties of Overlay Welded WC/NiSiB Composite Coatings, Höganäs, Sweden (2013), p. 64.
2. M. Gubisch, Y. Liu, S. Krischok, G. Ecke, C. Spieb, J.A. Shaefer, and C. Knedlik, “Tribological characteristics of WC1–x, W2C and WC tungsten carbide films,” Tribol. Interface Eng. Ser., 48, 409–417 (2005).10.1016/S0167-8922(05)80043-4 ↗
3. S. Rausch, P. Wiederkehr, D. Biermann, A. Zabel, U. Selvadurai, L. Hagen, and W. Tilmann, “Influence of machine hammer peening on the tribological behavior and the residual stresses of wear resistant thermally sprayed coatings,” in: Proc. CIRP Conference on Surface Integrity, Vol. 45 (2016), pp. 275–278.
4. I.M. Poletika, T.A. Krylova, M.V. Tetyutska, and S.A. Makarov, “Structurization of wear-resistant coatings by electron-beam deposition of tungsten carbide,” Svar. Proizv., No. 5, 9–15 (2012).
5. P.I. Loboda, I.Yu. Trosnikova, O.I. Bilyi, and O.P. Karasevska, “Effect of doping on the structure and properties of WC–W2C alloys,” Metalloznav. Obrob. Met., No. 2, 62–67 (2012).
6. I.Yu. Trosnikova, P.I. Loboda, O.I. Bilyi, and O.P. Karasevska, “Effect of the cooling rate during melt solidification on the structure and properties of WC–W2C,” Powder Metall. Met. Ceram., 52, No. 11–12, 674–679 (2014).10.1007/s11106-014-9576-4 ↗
7. V.N. Antsiferov, G.V. Bobrov, and L.K. Druzhinin, Powder Metallurgy and Sprayed Coatings [in Russian], B.S. Mitin (ed.), Moscow (1987), p. 792.
8. A.I. Belyi, B.V. Danilchenko, V.S. Goncharenko, and V.I. Dzykovich, “Facility for centrifugal spraying with a rod made of refractory materials,” USSR Inventor’s Certificate No. 1381840, publ. October 15 (1987).
9. M.A. Krivoglaz, Diffraction of X-Rays and Neutrons in Imperfect Crystals [in Russian], Kyiv (1983), p. 407.
10. I.Yu. Trosnikova, P.I. Loboda, and O.I. Bilyi, “Effect of molybdenum additions on the microstructure and properties of WC–W2C alloys,” Powder Metall. Met. Ceram., 53, No. 3–4, 219–224 (2014).10.1007/s11106-014-9607-1 ↗
11. P.I. Loboda, Physicochemical Fundamentals for Creation of New Boride Materials for Electronic Devices and Development of Ceramic Cathode Assemblies with Increased Efficiency [in Ukrainian], Author’s Abstract of ScD Thesis; specialty 05.16.06: Powder Metallurgy and Composites; Inst. Probl. Materialoznav. NANU, Kyiv (2004), p. 62.