journal article·2017-05

Surface–Interface Microstructures and Friction-Wear Performances of Thermal Sprayed FeCrBSi Coatings Obtained by High-Velocity Oxygen Fuel Process

Liu Wenming, Sheng Tianyuan, Kong Dejun

Powder Metallurgy and Metal Ceramics· Volume 56· Issue 1-2
Publisher page

Abstract

A layer of FeCrBSi coating was prepared on H13 hot work steel using a high-velocity oxygen fuel spraying (HVOF). The morphologies and distribution of chemical elements and phases in the obtained coatings were analyzed using a field emission scanning electron microscopy (FMSEM), energy dispersive spectrometry (EDS), and X-ray diffraction (XRD), respectively. The friction-wear performance of FeCrBSi coating was examined using a wear test, and the wear mechanism was also discussed. The results show that the coating is primarily composed of Fe, Cr, B, and Si elements, which are uniformly distributed in the coating, enriched in the coating, and poor in the substrate at the coating interface. Among them, the Fe content decreases gradually in the substrate–coating direction, the Fe content of the coating is 40% lower than that of the substrate. The Cr, B, and Si contents in the coating are higher than those in the substrate, which form compounds and diffusion at the interface; as a result, the coating is combined with the substrate in the form of metallurgical bonding. The coating has a good friction reduction and wear resistance, the average COF (coefficient of friction) is 0.2126, the wear rate is 1.5 ∙ 10–6 mm3/sec ∙ N, and the wear mechanism consists abrasive wear and spalling.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · High-Temperature Coating Behaviors · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (15)

Show source-provided references
1. M. J. Arab, M. Farzam, and H. Zohdirad, “Wear and corrosion resistance and electroplating characteristics of electrodeposited Cr–SiC nano-composite coatings,” Trans. Nonferrous Met. Soc. China, 23, No. 7, 1993–2001 (2013).10.1016/S1003-6326(13)62688-6 ↗
2. P. L. Ge, M. D. Bao, H. J. Zhang, et al., “Effect of plasma nitriding on adhesion strength of CrTiAlN coatings on H13 steels by closed field unbalanced magnetron sputter ion plating.” Surf. Coat. Technol., 229, No. 9, 146–150 (2013).
3. J. G. Gregory and G. H. Robert, “Thermal-sprayed coatings on aluminum for mould tool protection and upgrade,” J. Mater. Process. Technol., 204, No. 1–3, 184–191 (2008).
4. K. Y. Lee, S. Choi, J. Suh, and C. Y. Kang, “Effect of laser power and powder feeding on the microstructure of laser surface alloying hardened H13 steel using SKH51 powder,” Mater. Des., 95, No. 1, 173–182 (2016).10.1016/j.matdes.2016.01.079 ↗
5. J. Wang, J. F. Gu, X. X. Shan, et al., “Numerical simulation of high pressure gas quenching of H13 steel,” J. Mater. Process. Technol., 202, No. 1–3, 188–194 (2008).10.1016/j.jmatprotec.2007.08.059 ↗
6. I. A. Figueroa, I. Betancourt, G. Lara, and J. A. Verduzco, “Effect of B, Si, and Cr on the mechanical properties of Fe-based amorphous metallic ribbons,” J. Non-Cryst. Solids, 351, No. 37–39, 3075–3080 (2005).10.1016/j.jnoncrysol.2005.07.017 ↗
7. G. Castro, A. Fernández-Vicente, and J. Cid, “Influence of the nitriding time in the wear behavior of an AISI H13 steel during a crankshaft forging process,” Wear, 263, No. 7–12, 1375–1385 (2007).10.1016/j.wear.2007.02.007 ↗
8. C. Zhang, L. Liu, K. C. Chan, et al., “Wear behavior of HVOF-sprayed Fe-based amorphous coatings,” Intermetallics, 29, No. 29, 80–85 (2012).10.1016/j.intermet.2012.05.004 ↗
9. W. H. Liu, F. S. Shieu, and W. T. Hsiao, “Enhancement of wear and corrosion resistance of iron-based hard coatings deposited by high-velocity oxygen fuel (HVOF) thermal spraying,” Surf. Coat. Technol., 249, No. 7, 24–41 (2104).
10. L. N. Zhu, B. S. Xu, H. D. Wang, and C. B. Wang, “Determination of hardness of plasma-sprayed FeCrBSi coating on steel substrate by nanoindentation,” Mater. Sci. Eng. A, 528, No. 1, 425–428 (2010).10.1016/j.msea.2010.09.028 ↗
11. L. N. Zhu, B. S. Xu, H. D. Wang, and C. B. Wang, “On the evaluation of residual stress and mechanical properties of FeCrBSi coatings by nanoindentation,” Mater. Sci. Eng. A, 536, No. 3, 98–102 (2012).
12. R. Gonzalez, M. A. Garcia, I. Penuelas, et al., “Microstructural study of NiCrBSi coatings obtained by different processes,” Wear, 263, No. 1–6, 619–624 (2007).10.1016/j.wear.2007.01.094 ↗
13. X. H. Wang, M. Zhang, X. M. Liu, et al., “Microstructure and wear properties of TiC/FeCrBSi surface composite coating prepared by laser cladding,” Surf. Coat. Technol., 202, No. 15, 3600–3606 (2008).10.1016/j.surfcoat.2007.12.039 ↗
14. Y. B. Wang, S. S. Zhao, W. Y. Gao, et al., “Microstructure and properties of laser cladding FeCrBSi composite powder coatings with higher Cr content,” J. Mater. Process. Technol., 214, No. 4, 899–905 (2014).10.1016/j.jmatprotec.2013.12.009 ↗
15. Y. H. Qing, “Influence of molybdenum on the microstructure and properties of a FeCrBSi alloy coating deposited by plasma transferred arc hardfacing,” Surf. Coat. Technol., 225, No. 25, 11–20 (2013).