journal article·2010-07

Structure and properties of spray-formed tool steel with increased chromium content

O. M. Sidorchuk

Powder Metallurgy and Metal Ceramics· Volume 49· Issue 3-4
Publisher page

Abstract

The paper examines the structure of tool (corrosion-resistant) steel produced by spray forming followed by thermomechanical treatment. The optimal conditions for steel deformation are established. It is shown that the fine carbide component forms in melt quenching. As a result, there is no carbide inhomogeneity in alloyed tool steel after plastic deformation. The steel structure remains superfine after high-temperature (1090°C) hardening treatment. The bending strength of deformed hardened steel is 2500–2600 MPa, impact strength 230–200 kJ/ m2, and hardness 56–57 HRC.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Material Properties and Failure Mechanisms · Surface Treatment and Coatings

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. I. N. Golikov and S. B. Maslenkov, Dendrite Liquation in Steels and Alloys [in Russian], Metallurgiya, Moscow (1977), p. 218.
2. G. S. Ershov and L. A. Poznyak, Structurization and Formation of Steels and Alloys [in Russian], Naukova Dumka, Kiev (1993), p. 378.
3. E. Gudremon, “Tool steel with high chromium content,” in: Special Steels [Russian translation], Metallurgizdat, Moscow (1959), pp. 716–720.
4. Yu. A. Geller, Tool Steels [in Russian], Metallurgiya, Moscow (1975), p. 584.
5. L. A. Poznyak, “Prospects for developing tool steels,” in: Modern Materials Science in the 21s Century [in Russian], Naukova Dumka, Kiev (1998), pp. 502–518.
6. R. G. Brooks, C. Moore, A. G. Leatham, and J. S. Coombs, “The Osprey process,” Powder Metall., No. 2, 100–102 (1977).
7. L. A. Poznyak, Tool Steels [in Russian], Naukova Dumka, Kiev (1996), p. 488.
8. V. I. Ul’shin and K. L. Poznyak, “Spray formation of high-density alloy-steel powder blanks,” Powder Metall. Met. Ceram., 35, No. 9–10, 505–508 (1996).10.1007/BF01355966 ↗
9. O. M. Sidorchuk, “Structural research of spray-formed metal,” in: Modern Problems of Physical Materials Science (Collected Scientific Papers) [in Russian], Inst. Probl. Materialoved. NAN Ukrainy, Kiev (2005), pp. 99–103.
10. O. M. Sidorchuk, K. O. Gogaev, O. K. Radchenko, et al., “Structure and phase composition of sprayformed R2AM5 steel,” Metalloved. Obrab. Met., No. 4, 13–18 (2005).
11. “Advances and prospects of materials science in developing new materials,” in: Physical Materials Science, Structure and Properties of Materials [in Russian], Inst. Probl. Materialoved. NAN Ukrainy, Kiev (2005), p. 197.
12. A. Lawley, P. Mathur, D. Apelian, and A. Meystel, “Spray forming: process fundamentals and control,” Powder Metall., 33, No. 2, 109–111 (1990).10.1179/pom.1990.33.2.109 ↗
13. Atomization and Sprays, 8, January–February, 1–24 (1998).
14. K. A. Gogaev, V. I. Ul’shin, and O. N. Sidorchuk, “Effect of temperature and power treatment modes on the structure and properties of billets made of high-speed steel powders,” in: Improvement of Pressing Process and Equipment in Metallurgy and Mechanical Engineering (Collected Scientific Papers) [in Russian], Kramatorsk (2003), pp. 323–328.
15. K. A. Gogaev and V. I. Ul’shin, “Determination of the temperature range for deforming powder tool steels,” Powder Metall. Met. Ceram., 43, No. 11–12, 564–569 (2004).10.1007/s11106-005-0022-5 ↗
16. O. M. Sidorchuk, K. O. Gogaev, and O. K. Radchenko, “Economy alloyed spray-formed high-speed steels,” Metalloved. Obrab. Met., No. 2, 31–36 (2006).