Heat Resistance of VT6 Alloy with and Without Aluminum–Chromium Diffusion Coatings at 500, 700, and 900 °C
Source abstract
Abstract
This paper proposes a method for increasing the heat resistance of VT6 titanium alloy from 400 to 900 °C through complex saturation of its surface with aluminum and chromium in powder mixtures. The diffusion coatings formed on the alloy consist of titanium aluminides: Al3Ti, Al2Ti, AlTi, and AlTi3, which show high thermal stability ensured by adequate aluminum content required to create a surface alumina film. The outer coating Al3(Ti, Cr) layer contains 4.3–9.3 wt.% Cr, which may induce the formation of protective Cr2O3 oxide besides Al2O3. Increase in the microhardness of the VT6 alloy by a factor of 2 to 2.5, resulting from complex aluminum–chromium saturation, compared with the initial state should enhance its wear resistance.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Nuclear Materials and Properties · Titanium Alloys Microstructure and Properties · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (10)
Show source-provided references
1. Bo Wei, Ping-Ze Zhang, Zheng-Jun Yao, et al., “Cyclic oxidation behavior of plasma surface chromizing coating on titanium alloy Ti–6Al–4 V,” Appl. Surf. Sci., 261, 800–806 (2012).10.1016/j.apsusc.2012.08.102 ↗
2. N. N. Poondla, T. S. Srivatsan, A. Patnaik, and M. Petraroli, “A study of the microstructure and hardness of two titanium alloys: commercially pure and Ti–6Al–4 V,” J. Alloys Compd., 486, 162–167 (2009).10.1016/j.jallcom.2009.06.172 ↗
3. H. L. Du, P. K. Datta, D. B. Lewis, and J. S. Burnell-Gray, “Air oxidation behavior of Ti–6Al–4 V alloy between 650 and 850 °C,” Corros. Sci., 36, 631–642 (1994).10.1016/0010-938X(94)90069-8 ↗
4. Gyo Jung Hwan, Ju Jung Dong, and Kim Young Kyoo, “Effect of Cr addition on the properties of aluminide coating layers formed on TiAl alloys,” Surf. Coat. Technol., 154, 75–81 (2002)10.1016/S0257-8972(01)01716-9 ↗
5. W. Zhou, Y. G. Zhao, Q. D. Qin, et al., “A new way to produce Al + Cr coatings on Ti alloy by vacuum fusing method and its oxidation resistance,” Mater. Sci. Eng., 36, 254–259 (2006).10.1016/j.msea.2006.05.101 ↗
6. T. Nishimoto, T. Izumi, S. Hayashi, and T. Narita, “Effect of coating layer structures and suface treatment on the oxidation behavior of a Ti–50 at.% Al alloy,” Intermetallics, 11, 459–466 (2003).10.1016/S0966-9795(03)00025-6 ↗
7. N. P. Lyakishev (ed.), Phase Diagrams of Binary Metal Systems: Handbook (in 3 Vols.) [in Russian], Mashinostroenie, Moscow (1996), Vol. 1, p. 996
8. N. P. Lyakishev (ed.), Phase Diagrams of Binary Metal Systems: Handbook (in 3 Vols.) [in Russian], Mashinostroenie, Moscow (1997), Vol. 2, p. 676.
9. T. J. Jewtt, B. Ahrens, and M. Dahms, “Stability of TiAl in the Ti–Al–Cr system,” Mater. Sci. Eng., 225, No. 1–2, 29–37 (1997).10.1016/S0921-5093(96)10841-8 ↗
10. Chungen Zhoua, Xua Huibin, Gonga Shengkai, et al., “A study on aluminide and Cr-modified aluminide coatings on TiAl alloys by pack cementation method,” Surf. Coat. Technol., 132, 117–123 (2000).10.1016/S0257-8972(00)00911-7 ↗