journal article·2015-01

Characterization of Ball Milled Ni–Al2O3 Nanocomposite Powders

Taib Muhammad Arif, Nouari Saheb

Powder Metallurgy and Metal Ceramics· Volume 53· Issue 9-10
Publisher page

Abstract

Homogenous Ni–Al2O3 nanocomposite powders with uniform distribution of Al2O3 nanoparticles were obtained through ball milling of Ni and Al2O3 powders for 9 hours. Field emission scanning electron microscopy and X-ray mapping were used to characterize the ball milled powders and Al2O3 nanoparticles’ dispersion, respectively. The evolution of crystallite size and lattice strain in the nanostructured Ni powder was followed through X-ray diffraction. It was found that ball milling led not only to the uniform dispersion of the Al2O3 nanoparticles, but also to the reduction in crystallite size and increase in the lattice strain of the Ni phase. For the composite containing 5 wt.% Al2O3, the increase of milling time from 0 to 9 hours led to a continuous decrease of the crystallite size of the Ni phase from 1120 to 36 nm. For the composite containing 10 wt.% Al2O3, the increase of milling time from 0 to 2 hours augmented the lattice strain of the Ni phase and a further increase of milling time to 9 hours led to its decrease.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Metallic Glasses and Amorphous Alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. R. A. Andrievskii, “Directions in current nanoparticle research,” Powder Metal. Met. Ceram., 42, 624–629 (2003).10.1023/B:PMMC.0000022203.40716.f7 ↗
2. C. Suryanarayana and N. Al-Aqeeli, “Mechanically alloyed nanocomposites,” Prog. Mater. Sci., 58, 383–564 (2013).10.1016/j.pmatsci.2012.10.001 ↗
3. V. Viswanathan, T. Laha, K. Balani, A. Agarwal, S. Seal, “Challenges and advances in nanocompositeprocessing techniques,” Mater. Sci. Eng. R., 54, 121–286 (2009).10.1016/j.mser.2006.11.002 ↗
4. S. Azadehranjbar, F. Karimzadeh, M. H. Enayati, and N. Mahmoodi, “Properties of bulk Fe–Ni/CNT nanocomposites prepared by mechanical milling and sintering,” Int. J. Mod Phys. B, 27, Article number 1350102 (2013).10.1142/S0217979213501026 ↗
5. A. Hedayati, Z. Golestan, Kh. Ranjbar, and G. H. Borhani, “Effect of ball milling on formation of ZnAl2O4 by the reduction reaction of ZnO and Al powder mixture,” Powder Metal. Met. Ceram., 50, 268–274 (2011).10.1007/s11106-011-9328-7 ↗
6. D. Özyürek, S. Tekeli, A. Güral, A. Meyveci, and M. Gürü M., “Effect of Al2O3 amount on microstructure and wear properties of Al–Al2O3 metal matrix composites prepared using mechanical alloying method,” Powder Metal. Met. Ceram., 49, 289–294 (2010).10.1007/s11106-010-9235-3 ↗
7. M. Zhang, S. Zhu, M. Jun, and C. Wu, “Preparation of WC/MgO composite nanopowders by high-energy reactive ball milling and their plasma-activated sintering,” Powder Metal. Met. Ceram., 47, 525–530 (2008).10.1007/s11106-008-9054-y ↗
8. T. Mousavi, F. Karimzadeh, M. H. Abbasi, and M. H. Enayati, “Investigation of Ni nanocrystallization and the effect of Al2O3 addition by high-energy ball milling,” J. Mater. Proc. Tech., 204, 125–129 (2008).10.1016/j.jmatprotec.2007.10.077 ↗
9. Y. Shi, J. Ding, S. L. H. Tan, and Z. Hu, “Ni/Fe2O3 magnetic composite synthesized by mechanical alloying,” J. Mag. Mag. Mater., 256, 13–19 (2003).10.1016/S0304-8853(01)00484-X ↗
10. R. Ismail and I. I. Yaacob, “The formation of aluminides in intermetallic nickel aluminide-based nanocomposites,” J. Alloys Compd., 392, 214–217 (2005).10.1016/j.jallcom.2004.09.032 ↗
11. V. Udhayabanu, K. R. Ravi, V. Vinod, and B. S. Murty, “Synthesis of in-situ NiAl–Al2O3 nanocomposite by reactive milling and subsequent heat treatment,” Intermetallics, 18, 353–358 (2010).10.1016/j.intermet.2009.08.006 ↗
12. J. Li, F. Li, and K. Hu, “Preparation of Ni/Al2O3 nanocomposite powder by high-energy ball milling and subsequent heat treatment” J. Mater. Proc. Tech., 147, 236–240 (2004).10.1016/j.jmatprotec.2003.12.022 ↗
13. V. Udhayabanu, K. R. Ravi, K. Murugan, et al., “Development of Ni–Al2O3 in-situ nanocomposite by reactive milling and spark plasma sintering,” Metall. Mater. Trans A, 42, 2085–2093 (2011).10.1007/s11661-011-0602-6 ↗
14. Y. Waseda, K. Shinoda, and E. Matsubara, X-Ray Diffraction Crystallography, Springer-Verlag, Berlin Heidelberg, 2011.10.1007/978-3-642-16635-8 ↗
15. N. Saheb, A. S. Hakeem, A. Khalil, et al., “Synthesis and spark plasma sintering of Al–Mg-Zr alloys,” J. Cent. South Univ., 20, 7–14 (2013).10.1007/s11771-013-1452-8 ↗
16. A. S. Edelstein and R. C. Cammarata, Nanomaterials: Synthesis, Properties and Application, Institute of Physics, Bristol and Philadelphia, PA, 2002.
17. N. Al-Aqeeli, K. Abdullahi, A. S. Hakeem, et al., “Synthesis, Characterization and Mechanical Properties of SiC-reinforced Al-based Nanocomposites Processed by MA and SPS,” Powder Metall., 56, 149–157 (2013).10.1179/1743290112Y.0000000029 ↗
18. N. Al-Aqeeli, A. Kachalla, C. Suryanarayana, et al., “Structure of Mechanically Milled CNT-Reinforced Al-Alloy Nanocomposites,” Mater. Manuf. Process., 28, 984–990 (2013).
19. A. S. Bolokang and M. J. Phasha, “Solid-state transformation in ball milled nickel powder,” Mater. Lett., 64, 1894–1897 (2010).10.1016/j.matlet.2010.05.052 ↗
20. H. J. Fecht, E. Hellstern, Z. Fu, and W. L. Johnson, “Nanocrystalline metals prepared by high-energy ball milling,” Metall. Mater. Trans A, 21, 2333–2337 (1990).10.1007/BF02646980 ↗
21. S. Hwang, C. Nishimura, and P. G. McCormick, “Mechanical milling of magnesium powder,” Mater. Sci. Eng. A, 318, 22–33 (2001).10.1016/S0921-5093(01)01767-1 ↗