journal article·2013-05

Effect of doping with refractory rare-earth metals on the structure and properties of Al–5Zn–3Mg alloys produced by powder metallurgy and casting methods

Yu. V. Mil’man, O. D. Neikov, A. I. Sirko, N. P. Zakharova, G. I. Vasil’eva, A. O. Sharovskii, R. K. Ivashchenko, V. G. Tokhtuev, N. V. Semenov

Powder Metallurgy and Metal Ceramics· Volume 52· Issue 1-2
Publisher page

Abstract

The effect of doping with transition refractory metals on the structure and properties of Al–Zn–Mg alloys produced by different methods is studied. It is ascertained that the strength of cast alloys is increased by scandium and zirconium doping due to the modifying action of scandium that arrests recrystallization and precipitation of the fine-grained phase matrix-coherent Al3(Sc1–x Zr x ) phase; the strength of alloys obtained by powder metallurgy (P/M) methods increases to a smaller extent, in which the ultrahigh cooling rate of melt atomized by high-pressure water plays the basic role in forming the fine-grained structure. The strength of powder metallurgy alloys based on wateratomized powders is substantially higher than that of similar alloys produced by the conventional casting method (standard commercial cast alloys and alloys produced by granular technology). The advantages of P/M alloys over cast alloys are especially prominent in the absence of scandium doping. The highest strength of the P/M alloys with scandium (σb = 651 MPa and σ0.2 = 596 MPa) is shown by Al–5Zn–3Mg–0.5Mn–0.7Zr–0.3Sc. Among the P/M alloys without scandium, the highest strength is shown by Al–5Zn–3Mg–0.85Zr–0.22Cr–0.17Ni–0.15Ti alloy (σb = 618 MPa and σ0.2 = = 553 MPa).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Bauxite Residue and Utilization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. V. I. Elagin, “Issues of developing Al–Zn–Mg alloys,” Tekhnol. Leg. Splav., No. 3, 7–13 (1999).
2. V. I. Elagin, Doping of Aluminum Alloys with Transition Metals [in Russian], Metallurgiya, Moscow (1975).
3. V. I. Dobatkin, V. I. Elagin, and V. M. Fedorov, Rapidly Solidified Aluminum Alloys [in Russian], Vseross. Inst. Leg. Splavov, Moscow (1995).
4. O. D. Neikov, O. V. Krainikov, Yu. V. Mil’man, et al., Method of Producing Semifinished Articles from Aluminum Alloys [in Ukrainian], Ukrainian Patent 66588, Bulletin No. 9 (2005).
5. O. D. Neikov, Yu. V. Milman, and D. B. Miracle, “Effect of Sc alloying additions on structure and mechanical properties of P/M and cast high-strength Al alloys of same composition,” in: Proc. EURO PM2001, Vol. 2, Acropolis Convention Centre, Nice, France (2001), pp. 219–224.
6. Yu. V. Mil’man, O. D. Neikov, A. I. Sirko, et al., “Structure and properties of Al–Mg alloys depending on scandium and zirconium additions and production methods,” Powder Metall. Met. Ceram., 49, No. 7–8, 430–437 (2010).10.1007/s11106-010-9254-0 ↗
7. J. Lendvai, “Precipitation and strengthening in aluminum alloys,” Mater. Sci. Forum, 217–222, 43 (1996).10.4028/www.scientific.net/MSF.217-222.43 ↗
8. O. G. Senatorova, A. N. Uksusnicov, et al., “Influence of different minor additions on structure and properties of high-strength Al–Zn–Mg–Cu alloy sheets,” Mater. Sci. Forum, 331–337, 1249 (2000).10.4028/www.scientific.net/MSF.331-337.1249 ↗
9. C. Wolverton, “Cristal structure and stability of complex precipitate phases in Al–Cu–Mg–(Si) and Al–Zn–Mg alloys,” Acta. Mater., 49, 3129–3142 (2001).10.1016/S1359-6454(01)00229-4 ↗
10. D. V. Lotsko, Yu. V. Mil’man, N. A. Efimov, et al., “Structure and mechanical properties of the Al–Zn–Mg alloy doped with scandium and zirconium,” Metallofiz. Noveish. Tekhnol., Issue No. 21, No. 6, 9–16 (1999).
11. Yu. V. Mil’man, “Effect of scandium on the structure, mechanical properties, and corrosion resistance of aluminum alloys,” in: Progressive Materials and Technologies [in Russian], Akademperiodika, Kiev (2003), pp. 335–360.
12. E. McCafferty and J. P. Wightman, “Determination of the concentration of surface hydroxyl groups on metal oxide films by a quantitative XPS method,” Surf. Interface Anal., 26, 549 (1998).10.1002/(SICI)1096-9918(199807)26:8<549::AID-SIA396>3.0.CO;2-Q ↗
13. O. D. Neikov, D. V. Lotsko, A. I. Sirko, et al., “Properties of rapidly solidified powder alloys of Al–Zn–Mg system,” Mater. Sci. Forum, 396–402, No. 1, 223 (2002).
14. V. V. Zakharov and T. D. Rostova, “High-strength welding alloy 1970 in the Al–Zn–Mg system,” Metalloved. Term. Obrab. Met., No. 4, 10–17 (2005).
15. I. N. Friedlander, Deformable Aluminum Alloys [Russian translation], Metallurgiya, Moscow (1979), p. 208.
16. Yu. V. Shmakov, V. M. Fedorov, R. G. Martirosov, et al., Method for Producing Semifinished Articles from Aluminum Powder Alloys [in Russian], Russian Federation Patent 2025216, publ. December 30 (1994).
17. J. R. Davis (ed.), Aluminum and Aluminum Alloys, ASM Specialty Handbook (1994).