journal article·2000-09

Industrial Use of the High-Rate (Impact) Pressing of Metallic Powders

Genadii G. Serdyuk

Powder Metallurgy and Metal Ceramics· Volume 39· Issue 9-10
Publisher page

Abstract

Features of the high-rate (impact) pressing of metal powders are discussed. It is shown that impact pressing compacts powders to a relative density which is 97% of the theoretical value after a single loading. The pressure which exists during high-rate pressing is usually higher than the static pressure for the same density of the pressed powder. The force which presses the products out of the die is 1.5-2.5 times lower than in static pressing. Preliminary pressing of the powder reduces friction losses and ensures a more uniform distribution of density over the height of the product. Recommendations are given on the loading rate in high-rate pressing and on the use of this operation in relation to the shape of the product. An example is given to illustrate the use of high-rate pressing for making large-diameter gaskets from copper powder.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Powder Metallurgy Techniques and Materials · Advanced materials and composites · Injection Molding Process and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (13)

Show source-provided references
1. O. V. Roman and E. A. Doroshkevich, “Sintering of cermet products pressed by impact loads,” Poroshk. Metall., No. 5, 6-9 (1966).
2. O. V. Roman and E. A. Doroshkevich, “Pressing of iron powders by impact loads,” in: Powder Metallurgy [in Russian], LatINTI, Riga (1968), pp. 68-72.
3. R. Davis, “Use of high rates to press metal powders and forge powder semifinished products,” Powder Metallurgy [in Russian], Vysheish. Shk., Minsk (1987), Vol. 1, pp. 26-29.
4. I. D. Rodomysel'skii and G. G. Serdyuk, “Study of the high-rate pressing of metal powders,” in: First National Conference on Powder Metallurgy (transactions), Scientific-Technical Society of Mechanical Engineering, Sofia (1968), pp. 3-12.
5. G. G. Serdyuk, V. F. Reshetnikov, L. I. Svistun, and O. V. Mikhailov, “Impact pressing of brass powders,” Poroshk. Metall., No. 12, 25-29 (1985).
6. G. G. Serdyuk, L. I. Svistun, V. F. Reshetnikov, et al., “Experimental unit for the two-sided impact pressing of metal powders in closed dies,” Poroshk. Metall., No. 7, 95-99 (1981).
7. V. F. Reshetnikov, L. I. Svistun, G. G. Serdyuk, et al., “Heat generation during the impact pressing of iron powder,” Poroshk. Metall., No. 1, 5-7 (1983).
8. V. F. Reshetnikov, L. I. Svistun, and G. G. Serdyuk, “Stresses in the die during the impact pressing of metal powders,” Poroshk. Metall., No. 6, 22-26 (1985).
9. M. S. Koval'chenko, “Dynamics of the hot impact pressing of powdered materials,” Poroshk. Metall., No. 9, 24-31 (1992).
10. V. N. Kobrin, A. N. Meshcheryakov, V. D. Grechka, et al., “High-rate forming of a clad graphite semifinished product,” Poroshk. Metall., No. 3, 21-25 (1982).
11. A. T. Mamedov, “Development of a technology for pressing high-density products with the use of a method of gas drainage. I. Mathematical analysis of gas drainage from the mold and the intrapore pressure of the gases in the compacts,” Poroshk. Metall., Nos. 5-6, 34-39 (1994).
12. G. A. Meerson, B. A. Borok, and B. N. Lobashev, “Study of the hydrostatic pressing of metal powders,” in: Transactions of the VII All-Union Scientific-Technical Conferenc on Powder Metallurgy [in Russian], Erevan (1964), pp. 106-121.
13. Sano Yukio and Miyagi Kiyohiro, “Dynamic compaction and the effect of air contained within powder pores,” Int. J. Powder Metall. Powder Technol., 20, No. 2, 115-118, 120-124, 126-129 (1984).