journal article·2001-03

Potential of the High-Energy Hot Compaction in a Vacuum for Creating Materials with an Ultrafine Structure and High Strength

Anatolii V. Laptev

Powder Metallurgy and Metal Ceramics· Volume 40· Issue 3-4
Publisher page

Abstract

The typical form of specimens prepared by high-energy hot pressing in a vacuum using different deformation schemes and also the results of studying compaction, structure formation, and the physicomechanical properties of different materials in relation to billet heating temperature are presented. The structure and properties of specimens prepared by vacuum sintering are given for comparison. The efficiency of high-energy pressing of single-phase materials (nickel and molybdenum) and two-phase composites (dispersion-strengthened nickel Ni ― NiO and WC ― Co hard alloys) is demonstrated. The method makes it possible to prepare compact billets at quite low temperatures that provides retention of a fine-grained structure within them. As a result of this the materials have high mechanical properties that exceed those of specimens prepared by traditional methods.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced materials and composites · Powder Metallurgy Techniques and Materials · Polymer Science and Applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (13)

Show source-provided references
1. A. V. Laptev and S. S. Ponomarev, “Behavior of ultrafine powders of iron-block metals produced by salt pyrolysis during low-temperature pressing,” Proc. of the 1998 Powder Metallurgy World Congress and Exhibition (Granada, October 18-22, 1998), Vol. 1, Granada (1998).
2. E. Orowan, “Conditions for dislocation passage of precipitates,” Proc. Int. Symp. Stress in Metals and Alloys, London (1948).
3. G. V. Samsonov (ed.), Physicochemical Properties of Oxides: Handbook [in Russian], Metallurgiya, Moscow (1978).
4. H. Takagi, Y. Nishiyama, K. Sakamaki, and K. Yoshida, “Microstructure and hardness of Ni — NiO composites prepared by powder metallurgy,” Trans. Jap. Soc. Mech. Eng., 61, No. 589, 1933-1939 (1995).10.1299/kikaia.61.1933 ↗
5. K. Sakamaki, H. Takagi, Y. Nishiyama, and K. Yoshida, “Effect of NiO content on the mechanical properties of Ni — NiO composites prepared by powder metallurgy,” Trans. Jap. Soc. Mech. Eng., 62, No. 594, 299-305 (1996).10.1299/kikaia.62.299 ↗
6. K. I. Portnoi, B. N. Babich, and I. L. Svetlov, Composite Materials Based on Nickel [in Russian], Metallurgiya, Moscow (1979).
7. J. Gurland, “The fracture strength of sintered WC — Co alloys in relation to composition and particle spacing,” Trans. Met. Soc. AIME, 227, No. 1, 1146-1150 (1963).
8. J. L. Chermant and F. Osterstock, “Fracture toughness and the fracture of WC — Co composites,” J. Mat. Sci., 11, No. 12, 1939-1951 (1976).10.1007/BF00708272 ↗
9. A. Laptev, “Intercarbide surface is the main obstacle to increase fracture toughness and strength of hard metals,” Proc. PM'94, Powder Metallurgy World Congress (Paris, 6-9 June, 1994), Vol. 1, Paris (1994).
10. W.D. Schubert, A. Bock, and B. Lux, “General aspects and limits of conventional ultrafine WC powder manuacture and hard metal production,” Proc. 13th Int. Plansee Seminar, 4, 283-305 (1993).
11. S. Haglund, J. Algren, and B. Uhrenius, “Solid state sintering of cemented carbides ― an experimental study,” Zh. Metallkunde, 89, No. 5, 316-322 (1998).
12. J.-M. Missiaen and S. Roure, “A general morphological approach of sintering kinetics: application to WC — Co solid-phase sintering,” Acta. Mater., 46, No. 11, 3985-3993 (1998).10.1016/S1359-6454(98)00055-X ↗
13. A. Laptev, “Strength and fracture toughness of the WC — 16% Co fine-grained cemented carbide obtained under high pressure in solid phase,” Proc. 14th Int. Plansee Seminar'97 (May 12-16, 1997), Vol. 2, Reutte Tyrol (1997).