journal article·2016-11

Process Approaches for Producing Complex Composite Inoculants by Rolling of Powder Mixtures. II. Compacting Conditions, Structure, and Properties of Two-Component Model Systems Fe–FeSi and Al–FeSi

K. A. Gogaev, S. M. Voloshchenko, Yu. N. Podrezov, A. K. Radchenko, L. A. Radchenko, Ya. I. Yevych

Powder Metallurgy and Metal Ceramics· Volume 55· Issue 7-8
Publisher page

Abstract

The optimization of compacting processes for two-component model systems consisting of brittle and plastic components is discussed. Fe–FeSi and Al–FeSi compositions with different volume content of the plastic component are tested. The compaction is conducted by pressing with different compacting force. Mechanical properties of cylindrical compacts are determined by axial compression test and the Brazilian test. It is established that the content of brittle component must be ≤ 60% and the compaction force must be ≥ 400 MPa. With increasing compaction force, the strength of the compacts increases significantly. It is established that the application of both iron and aluminum as binder is acceptable. However, iron and aluminum compositions are the best for low and high content of the brittle component, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Powder Metallurgy Techniques and Materials · Metal Alloys Wear and Properties · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (9)

Show source-provided references
1. K. A. Gogaev, S. M. Voloshchenko, Yu. N. Podrezov, et al., “Process Approaches for Producing Complex Composite Inoculants by Rolling Of Powder Mixtures. I. Inoculant Powder Mixtures. Composition, Structure, And Properties,” Powder Metall. Met. Ceram., 55, No. 5–6, 270–276 (2016).10.1007/s11106-016-9802-3 ↗
2. Yu. N. Semenov, New Methods for Controlling the Quality of Metallic Powder Compacts/Development of Methods for Forming Powder Products [in Russian], Inst. Probl. Materialloved. AN UkrSSR, Kiev (1976), p. 156.
3. A. F. Zhornyak and V. E. Oliker, “Effect of the particle size distribution of atomized iron powder and mixtures of atomized and reduced iron powders on some properties of materials produced from them by pressing and sintering,” Powder Metall. Met. Ceram., 17, No. 7, 558–561 (1978).10.1007/BF00791936 ↗
4. O. K. Radchenko, K. O. Gogaev, V. K. Grybkov, and G. G. Orel, Method and Device for Determination of Angle of Natural Slant of Bulk Materials. Ukrainian Patent No. 86891 Ukraine, MPK G01B5/24, B22F1/00. Applicant and Owner: Frantsevich Institute for Problems of Materials Science, National Academy of Sciences of Ukraine, Kiev No. a200712358; Appl. 07.11.07; Publ. 25.05.09; Bull. No. 10; p. 7.
5. Yu. N. Podrezov, D. G. Verbylo, and Ya. I. Yevych, “Fraction strains in consolidating of powder materials,” Fiz. Tekh. Vys. Davl., No. 1, 46–54 (2014).
6. A. K. Radchenko, M. S. Koval’chenko, and D. N. Brodnikovskii, “Compaction and strain hardening of metal powders and their mixtures when pressed,” Powder Metall. Met. Ceram., 48, No. 5–6, 267–273 (2009).10.1007/s11106-009-9134-7 ↗
7. D. J. Bergman, “Elastic moduli near percolation: universal ratio and critical exponent,” Phis. Rev. B. 31, No. 3, 1696–1698 (1985).10.1103/PhysRevB.31.1696 ↗
8. G. A. Vinogradov, Yu. N. Semenov, O. A. Katrus, and V. P. Katashinskii, Rolling the Metallic Powders [in Russian], Metallurgiya (1969), p. 382.
9. K. A. Gogaev and A. K. Radchenko, Forming the Powder Systems [in Russian], Knowledge, Donetsk (2011), p. 477.