journal article·2004-07

Crack Resistance of Modern Ceramics and Ceramic Composites. Part 1. SEVNB-Method

Georgii A. Gogotsi

Powder Metallurgy and Metal Ceramics· Volume 43· Issue 7-8
Publisher page

Abstract

The crack resistance of monolithic and single-crystal ceramics, as well as laminar and normal composites based on them, are studied by the SEVNB method (bending a specimen with a V-shaped notch) over a wide temperature range. Manual and mechanical procedures for preparing a V-shaped notch and also test procedures for three- and four-point bending are described. Ceramic deformation curves at different temperatures are studied. Results of testing by the methods of SENB (specimen bending with a blunt notch) and SEPB (specimen bending with a sharp crack) as well as micro-Raman spectroscopy data are analyzed. It is established that the ratio of crack resistance values according to the SEPB and SENB methods is about 0.6 only for linearly-elastic monolithic and normal composite ceramics and it exceeds 0.9 for the same inelastic ceramic. Polishing a V-notch does not give rise to a tetragonal-monoclinic phase transition in zirconium dioxide ceramic.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Nuclear materials and radiation effects · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. W. F. Brown and J. E Srawley, “Plain strain crack toughness testing of high strength metallic materials,” ASTM STP 410, American Society for Testing of Materials, Pennsylvania (1966).
2. R. J. Myers and B. M. Hillberry, “Effect of notch root radius on the fracture behavior of monocrystalline silicon,” Fracture, 3, 1001–1005 (1977).
3. A. D. Vasil'ev, G. Ya. Akimov, and A. Yu. Koval', “Zirconium ceramics and their perspectives in the Ukraine,” Ogneupory i Tekhn. Keramika, No. 10, 2–5 (2000).
4. A. G. Evans and E. A. Charles, “Fracture toughness determination by indentation,” J. Amer. Ceram. Soc., 59, Nos. 7-8, 371–372 (1976).10.1111/j.1151-2916.1976.tb10991.x ↗
5. D. J. Roweliffe, “Indentation of ceramics,” in: Introduction of Mechanical Behavior of Ceramics, IRTEC, Faenza (1992).
6. G. D. Quinn, J. A Salem, I. Bar-On, and M. G. Jenkins, “The new ASTM fracture toughness of advance ceramics standard,” Ceram Eng. Sci. Proc., No. 3, 565–579 (1998).
7. M. Stech and J. Rodel, “Method for measuring short-crack R-curves with calibration parameters: case studied on alumina/aluminum composites,” J. Amer. Ceram. Soc., No. 2, 291–297 (1996).10.1111/j.1151-2916.1996.tb08119.x ↗
8. Z. Li, A. Grosh, A. S. Kobayashi, and R. C. Bradt, “Indentation fracture toughness of sintered silicon carbide in Palmquist crack regime,” J. Amer. Ceram. Soc., No. 6, 904–910 (1989).10.1111/j.1151-2916.1989.tb06242.x ↗
9. K. Tsacuma, “Mechanical properties and thermal stability of CeO2 containing tetragonal zirconia polycrystal,” Amer. Ceram. Soc. Bull., No. 12, 1594–1596 (1985).
10. H. Fischer and R. Marx, “Fracture toughness of dental ceramics: comparison of bending and indentation method,” Dental Mat., No. 1, 112–119 (2002).
11. R. J. Primas and R. Gstrein, “EISS TC6 Round Robin of fracture toughness,” EPMA Report No. 155'088, Swiss Federal Laboratories for Materials Testing and Research, Dubendorf, October (1995).
12. G. Gogotsi, S. Mudrik, and G. Quinn, “Crack resistance of the edge of silicon nitride ceramic: procedure and results,” Proc. Int. Conf. “New technologies in powder metallurgy and ceramics” (Kiev, Ukraine 2003), Institute for Problems of Materials Science, National Academy of Sciences of Ukraine, Kiev (2002).
13. ASTM C1421-99, “Standard test method for the determination of fracture toughness of advanced ceramics at ambient temperature,” Annual Book of ASTM Standards, American Society for Testing materials, Pennsylvania (1999).
14. G. D. Quinn, K. Xu, R. J. Gettings, et al., “Does anyone know real fracture toughness?,” in: Fracture Resistance Testing of Monolithic and Composite Brittle Materials, ASTM STP 1409, J. A. Salem, G. D. Quinn, and M. G. Jenkins (eds.), American Society for Testing and Materials, Pennsylvania (2002).
15. G. A. Gogotsi, “Fracture toughness studies on ceramics and ceramic particulate composites at different temperature,” in: Fracture Resistance Testing of Monolithic and Composite Brittle Materials, ASTM STP 1409, J. A. Salem, G. D. Quinn, and M. G. Jenkins (eds.), American Society for Testing and Materials, Pennsylvania (2002).
16. G. D. Quinn, J. Salem, I. Isa Bar-On, et al., “Fracture toughness of advanced ceramics at room temperature,” J. Res. Nat. Inst. Standard Techn., No. 97, 579–607 (1992).10.6028/jres.097.026 ↗
17. G. A. Gogotsi, “Mechanical behavior of yttria-and ferric oxide-doped zirconia at different temperatures,” Ceram. Int., No. 8, 589–595 (1998).10.1016/S0272-8842(97)00060-6 ↗
18. Le Bac, Verfarenzum feinkerben von keramischen korpern (Procedure to make small notches into ceramic parts), Pat. 146416 GDR, Publ. 1979-1981.
19. J. Kubler, “Fracture toughness of ceramics using the SEVNB method: round robin,” VAMAS Report. No. 37, ESIS Document D2-99, Swiss Federal Laboratories for Materials Testing and Research, Dubendorf (1999).
20. G. A. Gogotsi, “Crack resistance of ceramics and composites with ceramic matrices (SEVNB method),” Ogneupory i Tekhn. Keramika, No. 11, 7–13 (1998).
21. G. A. Gogotsi and V. I. Galenko, “Crack resistance of ceramics and crystals at room and low temperatures,” Probl. Prochn., No. 3, 104–118 (1997).
22. G. A. Gogotsi, “Study of the crack resistance in specimens with a V-shaped notch,” Probl. Prochn., No. 1, 120–17 (2000).
23. G. A. Gogotsi, V. P. Zavada, and V. P. Nerodenko, Inventor's Certificate 1224551 USSR, “Device for measuring specimen deflection,” Otkrytiya. Izobreteniya, No. 14 (1986).
24. DIN 51 109, “Testing of advanced technical ceramics; determination of fracture toughness K 1c,” Deutsches Institut für E. V. Numang, Publ. December 31 (1991).
25. G. A. Gogotsi and E. E. Lomonova, “Micro-Raman studies of phase transitions for crystals on introducing a Vickers indentor,” Ogneupory i Tekhn. Keramik, No. 6, 4–9 (2000).
26. M. Mizuno, Y. Nagano, J.-W. Cao, and J.-I. Kon, “VAMAS round robin on fracture toughness measurement in ceramic matrix composite,” Abstr. 9 th Int. Conf. on Modern Mater. and Technologies (CIMITEC'98, Florence, Italy), Grafiche Galeati (1998).
27. T Nishida, Y. Hanaki, and G. Pezotti, “Effect of notch-root on the fracture toughness of a fine-grained alumina,” J. Amer. Ceram. Soc., No. 2, 606–608 (1994).10.1111/j.1151-2916.1994.tb07038.x ↗
28. M. Mizuno and H. Okuda, “VAMAS round robin on fracture toughness of silicon nitride,” J. Amer. Ceram. Soc., No. 7. 1793–1801 (1995).10.1111/j.1151-2916.1995.tb08891.x ↗
29. R. W. Davidge and G. Tappin, “The effective surface energy of brittle materials,” J. Mat. Sci., No. 3, 165–173 (1968).10.1007/BF00585484 ↗
30. G. A. Gogotsi, “Deformation behavior of ceramics,” J. Eur. Ceram. Soc., No. 2, 87–92 (1991).10.1016/0955-2219(91)90005-K ↗
31. G. A. Gogotsi, “Mechanical behavior of ceramics not following Hooke's law,” Poroshk. Metall., No. 11, 79–85 (1988).
32. J. Wang, E. M. Raiferth, I. Wadsworth, and R. Stevens, “Effect of notch width on the SENB toughness for oxide ceramics,” J. Eur. Ceram. Soc., No. 1, 21–31 (1992).10.1016/0955-2219(92)90115-T ↗
33. G. A. Gogotsi, “The use of brittleness measure (× ) to represent mechanical behavior of ceramics,” Ceram. Int., No. 15, 127–129 (1989).10.1016/0272-8842(89)90025-4 ↗
34. Fine Ceramics (Advanced Ceramics, Advances Technical Ceramics)–Test Method for Fracture Toughness at Room Temperature by Single Edge Precracked Beam (SEPB) Method, ISO DIS 15732, Int. Org. for Standardization (1998).
35. G. A. Gogotsi, A. V. Drozdov, V. P. Zavada, and M. V. Swain, “Comparison of the mechanical behavior of partially stabilized zirconia with yttria and magnesia,” J. Austr. Ceram. Soc., No. 27, 37–49 (1991).
36. J. Kubler, “Fracture toughness of ceramics using the SEVNB method: from a preliminary study to a standard test method,” in: Fracture Resistance of Monolithic and Composite Brittle Materials, ASTM STP 1409, J. A. Salem, G. D. Quinn, and M. G. Jenkins (eds.), American Society for Testing and Materials, Pennsylvania (2002).