journal article·2022-05

Modeling of Powder Bed Deformation in the Binder Jetting Technology

O.P. Maidaniuk, A.L. Maximenko, D. Olumor, E. Torresani, M.B. Shtern, E. Olevsky

Powder Metallurgy and Metal Ceramics· Volume 61· Issue 1-2
Publisher page

Abstract

No abstract is available for this record. The assistant can identify its topic from the title, but cannot infer the study’s results.

Source: Not provided · Quality: missing

Research context

OpenAlex topics: Granular flow and fluidized beds · Engineering Technology and Methodologies · Injection Molding Process and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (12)

Show source-provided references
1. E. Sachs, M. Cima, and J. Cornie, “Three dimensional printing: rapid tooling and prototypes directly from CAD representation,” CIRP Ann. Manuf. Technol., 39, No. 1, 201–204 (1990), https://doi.org/10.1016/S0007-8506(07)61035-X.10.1016/S0007-8506(07)61035-X ↗
2. H. Miyanagi, M. Orth, J.M. Akbar, and L. Yang, “Process development for green part printing using binder jetting additive manufacturing,” Front. Mech. Eng., 13, No. 4, 504–512 (2018), https://doi.org/10.1007/s11465-018-0508-8.10.1007/s11465-018-0508-8 ↗
3. G. Lee, M. Maricruz Carrillo, J. McKittrick, G. Darold, D.G. Martin, A. Eugene, and E.A. Olevsky, “Fabrication of ceramic bone scaffolds by solvent jetting 3D printing and sintering: Towards load-bearing application,” Addit. Manuf., 33 (5484), 101107 (2020), https://doi.org/10.1016/j.addma.2020.101107.10.1016/j.addma.2020.101107 ↗
4. K. Lu and W.T. Reynolds, “3DP process for fine mesh structure printing,” Powder Technol., 187, 11–18 (2008), DOI: https://doi.org/10.1016/j.powtec.2007.12.017.10.1016/j.powtec.2007.12.017 ↗
5. M. Salehi, M. Gupta, S. Maleksaedi, and N.M.L. Sharon, Inkjet Based 3D Additive Manufacturing of Materials, MRF (2018), p. 158.
6. M. Asadi-Eydirand, M. Soleti-Hashijn, A. Farzad, and N.A.A. Osman, “Effect of technical parameters on porous structure and strength of 3D printed calcium sulfate prototypes,” Rob. Comput. Integr. Manuf., 37, 57–67 (2016), https://doi.org/10.1016/j.rcim.2015.06.005.10.1016/j.rcim.2015.06.005 ↗
7. M. Vaezi and C.K. Chua, “Effect of layer thickness and binder saturation level parameters on 3D printing process,” Int. J. Adv. Manuf. Technol., 53, 275–284 (2011), https://doi.org/10.1007/s00170-010-2821-1.10.1007/s00170-010-2821-1 ↗
8. D.M. Mueth, “Measurements of particle dynamics in slow, dense, granular Couette flow,” Phys. Rev., E67, 011304 (2003), DOI: https://doi.org/10.1103/PhysRevE.67.011304.10.1103/PhysRevE.67.011304 ↗
9. D. Howell, R.P. Behringer, and C. Veje, “Stress fluctuations in a 2D granular Couette experiment: a continuous transition,” Phys. Rev. Lett., 82, 5241–5245 (1999), https://doi.org/10.1103/PhysRevLett.82.5241.10.1103/PhysRevLett.82.5241 ↗
10. C.H. Ryeroff, K. Kamrin, and M.Z. Bazant, “Assessing continuum postulates in simulation of granular flow,” J. Mech. Phys. Solids, 57, 828–839 (2009), https://doi.org/10.1016/j.jmps.2009.01.009.10.1016/j.jmps.2009.01.009 ↗
11. E. Coumans, Bullet 2.83 Physics SDK Manual (2015), https://github.com/bulletphysics/bullet3.
12. L.C. Li and G.E. Peck, “The effect of moisture content on the compression properties of maltodextrins,” J. Pharm. Pharmacol., 42, 272–275 (1990), DOI: https://doi.org/10.1111/j.2042-7158.1990.tb05406.x.10.1111/j.2042-7158.1990.tb05406.x ↗