Wear Resistance of Plasma-Sprayed Coatings in Intensive Abrasive Wear Conditions
Source abstract
Abstract
The abrasive wear resistance of plasma-sprayed oxide ceramic (Al2O3 and Cr2O3) and clad cermet ((Ti–Cr–C)–30% Ni and (TiC)–30% Ni) coatings was studied. The wear characteristics of the coatings such as wear rates, friction forces, friction coefficients, and wear groove depth determined with two methods were compared. The wear test methods included simulation of the friction process using loose abrasive particles and reciprocal ball-on-disk friction using a diamond indenter. The plasma-sprayed TiC-based coatings showed the lowest wear rate and can be applied to protect equipment parts subjected to intensive abrasive wear. The wear loss of the (Ti–Cr–C)–30% Ni and (TiC)–30% Ni coatings determined by friction against loose abrasive particles was 10–17 μm, while the wear loss of the oxide ceramic coatings was 20–42 μm, being 2–2.5 times higher on average.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. Yu.S. Korobov, “International Thermal Spraying Conference ITSC 2010: review and analysis,” in: Proc. Int. Sci. Workshop [in Russian] (September 28–29, 2010), Ekaterinburg (2010), pp. 4–26.
2. L.Kh. Baldaev (ed.), V.N. Borisov, V.A. Vakhalin, G.I. Gannochenko, A.E. Zatoka, B.M. Zakharov, A.V. Ivanov, V.M. Ivanov, V.I. Kalita, V.V. Kudinov, A.F. Puzriakov, Y.Pu. Sborshchikov, B.G. Khamishchev, E.Ya. Shkolnikov, and V.M. Yaroslavtsev, Thermal Spraying: Handbook [in Russian], DS Market, Moscow (2007), p. 344.
3. L. Pavlowski, The Science and Engineering of Thermal Spray Coatings, John Willey & Sons, Chichester (2008), p. 626.10.1002/9780470754085 ↗
4. A.Ya. Kulik, Yu.S. Borisov, and A.S. Mnukhin, Thermal Spraying of Composite Powders [in Russian], Mashinostroenie, Leningrad (1985), p. 197.
5. O. Umanskyi, I. Hussainova, M. Storozhenko, O. Terentyev, O. Umanskyi, and M. Antonov, “Effect of oxidation on sliding wear behavior of NiCrSiB–TiB2 plasma sprayed coatings,” Key Eng. Mater., 604, 16–19 (2014).10.4028/www.scientific.net/KEM.604.16 ↗
6. N.J. Sari and M. Yilmaz, “Improvement of wear resistance of wire drawing rolls with Cr–Ni–B–Si+WC thermal spraying powders,” Surf. Coat. Technol., 202, No. 13, 3136–3141 (2008).10.1016/j.surfcoat.2007.11.022 ↗
7. V.I. Kalita, D.I. Komlev, A.V. Samokhin, and Yu.V. Blagoveshchenskii, “Plasma-sprayed cermet WC–Co coatings reinforced by micro- and nanosized carbides,” Fiz. Khim. Obrab. Mater., No. 6, 41–45 (2008).
8. I.N. Gorbatov, M.Y. Berezhneva, A.E. Terentev, N.F. Stliverstov, V.A. Ryabin, and N.S. Il’chenko, “Properties of plasma coatings made of heat-treated chromium-oxide powders,” Powder Metall. Met. Ceram., 30, No. 11, 986–988 (1991). 566
9. A.P. Kudrin, V.F. Labunets, and O.A. Vishnevskii, “Studying the wear resistance of hardened carbon steel in abrasive wear conditions,” Visn. Nat. Akad. Ukrainy, No. 2, 111–114 (2003).
10. GOST 23.208–79, Wear Resistance of Parts. Wear Resistance Test of Materials by Friction against Loose Abrasive Particles [in Russian], Standartinform, Moscow (2005), p. 5.
11. S.R. Ignatovich, I.M. Zakiev, and E.P. Pugachevskaya, “Micro attrition testing machine for materials and coatings,” Probl. Tribol., 50, No. 7, 50–57 (2008).
12. A.P. Umanskii, M.S. Storozhenko, I.V. Hussainova, A.E. Terentiev, A.M. Kovalchenko, and M.M. Antonov, “Structure, phase composition and wear mechanisms of plasma-sprayed NiCrBSi–20 wt.% TiB2 coating,” Powder Metall. Met. Ceram., 53, No. 11–12, 663–671 (2015).10.1007/s11106-015-9661-3 ↗
13. O. Umanskyi, M. Storozhenko, I. Hussainova, O. Terentyev, A. Kowalchenko, and M. Antonov, “Effect of TiB2 additives on wear behavior of NiCrSiB–based plasma sprayed coatings,” Mater. Sci., 22, No. 1, 15–19 (2016).