Kinetics of Nonisothermal Pressure Sintering of Zirconium Diboride Powder with Additives of Boron and Chromium Carbides in Vacuum
Source abstract
Abstract
The analysis of the experimental data on the kinetics of nonisothermal pressure sintering of zirconium diboride-based powder mixtures with the addition of boron and chromium carbides in vacuum showed a division of the sintering temperature mode into low-temperature and hightemperature areas. The division is clearly observed when the temperature increases at a rate of 20°C/min. In low-temperature area, the densification occurs slowly and hardly depends on the temperature. In high-temperature area, the viscous flow of the matrix of the porous material is controlled by the power-law creep of the matrix forming the porous body with an activation energy of 394 kJ/mol. Twofold increase in heating rate leads to acceleration of low- and high-temperature strain of the matrix and increase in the apparent activation energy to 581 kJ/mol, indicating the series engagement of additional mechanisms of material flow. The investigation of structure and properties of materials has showed that the formation of new boron–carbide phases and eutectic that disappears during sintering activates the densification of the porous material. It is found out that under low pressure nonisothermal sintering, a superplasticity phenomenon can occur, which results in the densification of the porous body to the virtually non-porous state.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Advanced ceramic materials synthesis · Powder Metallurgy Techniques and Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (31)
Show source-provided references
1. M. S. Kovalchenko, “Hot pressing of powders of refractory compounds and materials based on them,” Powder Metall. Met. Ceram., 37, Nos. 1–2, 37–44 (1998).10.1007/BF02677228 ↗
2. G. V. Samsonov and M. S. Kovalchenko, “Some aspects of sintering refractory compound,” Powder Metall. Met. Ceram., No. 1, 20–29 (1961).
3. G. V. Samsonov and M. S. Kovalchenko, “Application of viscous flow theory in sintering of powders of refractory compounds by hot pressing,” Powder Metall. Met. Ceram., No. 2, 3–13 (1961).
4. M. S. Kovalchenko and G. V. Samsonov, “Viscous flow during sintering of zirconium boride by hot pressing,” Powder Metall. Met. Ceram., No. 5, 3–9 (1961).
5. G. V. Samsonov and M. S. Kovalchenko, Hot Pressing [in Russian], Gostekhizdat UkrSSR, Kyiv, (1962), p. 212.
6. M. S. Kovalchenko and Yu. I. Rogovoi, “Microstructure of hot-pressed molybdenum carbide,” Powder Metall. Met. Ceram., 9, No. 12, 1013–1017 (1970).10.1007/BF00805075 ↗
7. M. S. Kovalchenko and L. F. Ochkas, “Creep in the hot pressing of titanium carbide powder,” Powder Metall. Met. Ceram., 12, No. 1, 23–31 (1973).10.1007/BF00803970 ↗
8. M. S. Kovalchenko, “Creep in the hot pressing of powders of titanium nitride, molybdenum disilicide, zirconium and chromium diborides,” Powder Metall. Met. Ceram., 12, No. 4, 272–276 (1973).10.1007/BF00791185 ↗
9. M. S. Kovalchenko and M. M. Mai, “Creep in the hot pressing of titanium diboride powder,” Powder Metall. Met. Ceram., No. 12, 8, 622–225 (1973).10.1007/BF00794381 ↗
10. M. S. Kovalchenko and L. F. Ochkas, “Creep in the hot pressing of Zirconium carbide powder,” in: 3-d All-Union Scientific-Technical Conference on Metal–Ceramic Materials and Products [in Russia], Izdat. Yerevan Politekh. Inst., Yerevan (1973), pp. 139–143.
11. M. S. Kovalchenko, “Creep in hot pressing of powders of some refractory compounds,” in: Sintering: Theory and Practice, ed. by M. M. Ristic, Herceg-Novi (1973), p. 308–316.
12. M. S. Kovalchenko, Fundamentals of Heat Treatment of Porous Materials by Pressure [in Russian], Nauk. Dumka, Kiev (1980), p. 238.
13. M. S. Kovalchenko, “Pressure sintering kinetics of tungsten and titanium carbides,” Int. J. Ref. Met. Hard Mat., 39, 32–37 (2013).10.1016/j.ijrmhm.2013.03.001 ↗
14. F. Monteverde, D. D. Fabbriche, and Bellosi,” Zirconium diboride-based composites,” Key Eng. Mater., 206–213, 961–964 (2002).10.4028/www.scientific.net/KEM.206-213.961 ↗
15. J. J. Meléndez-Martínez, A. Domínguez-Rodriguez, F. Monteverde, et al., “Characterisation and high temperature mechanical properties of zirconium boride-based materials,” J. Europ. Ceram. Soc., 22, Nos. 14–15, 2543–2549 (2002).10.1016/S0955-2219(02)00114-0 ↗
16. A. L. Chamberlain, W. G. Fahrenholtz, and G. E. Hilmas, “Low-temperature densification of zirconium diboride ceramics by reactive hot pressing,” J. Am. Ceram. Soc., 89, No. 12, 3638–3645 (2006).10.1111/j.1551-2916.2006.01299.x ↗
17. J. K. Sonber, T. S. R. Ch. Murthy, C. Subramanian, et al., “Investigations on synthesis of ZrB2 and development of new composites with HfB2 and TiSi2,” Int. J. Ref. Met. Hard Mat., 29, 21–30 (2011).10.1016/j.ijrmhm.2010.06.007 ↗
18. Eric W. Neuman, “Elevated temperature mechanical properties of zirconium diboride based ceramics,” (2014). Doctoral Dissertations. 2164. Path to the source http://scholarsmine.mst.edu/doctoral_dissertations/2164 .
19. M. W. Bird, R. P. Aune, A. F. Thomas, et al., “Temperature-dependent mechanical and long crack behavior of zirconium diboride–silicon carbide composite,” J. Europ. Ceram. Soc., 32, 3453–3462 (2012).10.1016/j.jeurceramsoc.2012.03.029 ↗
20. O. N. Grigiriev, V. B. Vinokurov, L. I. Klimenko, et al., “Sintering of zirconium doboride and phase transformations in the presence of Cr3C2,” Powder Metall. Met. Ceram., 55, Nos. 3–4, 185–194 (2016).10.1007/s11106-016-9793-0 ↗
21. V. G. Kayuk and V. A. Maslyuk, “Structure formation in alloys of the Cr3C2–TiN system and the properties of materials based on them,” Powder Metall. Met. Ceram., 43, Nos. 1–2, 39–43 (2004).10.1023/B:PMMC.0000028270.54924.60 ↗
22. B. A. Galanov and O. N. Grigoriev, “Analytical model for indenting brittle materials,” in: Electronic Microscopy and Strength of Materials. Frantsevich Institute for Problems of Materials Science, NAS Ukraine, Issue 13, Kiev (2006), pp. 4–42.
23. B. A. Galanov, O. N. Grigoriev, and E. G. Trunova, “Static Characteristics of Contact Strength of Ceramics,” in: Electronic Microscopy and Strength of Materials, Frantsevich Institute for Problems of Materials Science, NAS Ukraine, Issue 8, Kiev (2001), pp. 125–135.
24. O. N. Grigoriev, B. A. Galanov, V. A. Kotenko, et al., “Contact strength and fracture toughness of brittle materials,” Metallofiz. Nov. Tekhnol., No. 8, 1001–1018 (2005).
25. A. Ango, Mathematics for Electrical and Radio Engineers [Russian translation], Nauka, Moscow (1965), p. 779.
26. M. S. Kovalchenko, “Pressure sintering of powder materials,” Powder Metall. Met. Ceram., 50, Nos. 1–2, 18–33 (2011).10.1007/s11106-011-9299-8 ↗
27. D. S. Wilkinson and M. F. Ashby, “Pressure sintering by power law creep,” Acta Met., 23, No. 11, 1277–1285 (1975).10.1016/0001-6160(75)90136-4 ↗
28. V. V. Skorokhod, Rheological Bases of Sintering Theory [in Russian], Nauk. Dumka, Kiev (1972), p. 152.
29. M. S. Kovalchenko, “Joint effects of various flow mechanisms in a porous polycrystalline body in hot pressing. Part I. General theory,” Powder Metall. Met. Ceram., 30, No. 7, 562–566 (1991).10.1007/BF00794646 ↗
30. M. S. Kovalchenko, “Combined effect of different flow mechanisms of a porous crystalline body in hot compacting. Part III. Successive connection model,” Powder Metall. Met. Ceram., 30, No. 9, 730–734 (1991).10.1007/BF00794209 ↗
31. M. V. Grabsky, Structural Superplasticity of Metals [Russian translation], Metallurgizdat, Moscow (1975), p. 269.