Effect of Porosity on Strength and Electrical Conductivity of NiO–3.5YSZ Composite and Its Ni–3.5YSZ Cermet
Source abstract
Abstract
The change in porosity of the Ni–3.5YSZ (ZrO2 stabilized with 3.5 mol.% Y2O3) composite, when produced, and the effect of porosity on the strength and electrical conductivity is studied. The porosity was provided by adding granular starch to the mixture of NiO and 3.5YSZ powders. The content of 18 vol.% pore-forming agent in the Ni–3.5YSZ cermet provides open porosity 47.1%, while its strength and electrical conductivity are 74.3 MPa and 0.93 · 106 S/m, respectively.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Advanced materials and composites · Electrical and Thermal Properties of Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. S. C. Singhal and K. Kendall, High-Temperature Solid Oxide Fuel Cells: Fundamentals, Design and Applications, Elsevier, Oxford, U. K. (2003), p. 406.
2. S. Shaikh, A. Muchtar, and M. Somalu, “A review on selection of anode materials for solid oxide fuel cells,” Ren. Sust. Ener. Rev., 51, 1–8 (2015).10.1016/j.rser.2015.05.069 ↗
3. O. Vasylyev, M. Brychevskyi, and Y. Brodnikovskyi, “The structural optimization of ceramic fuel cells,” Univ. J. Chem., 4, No. 2, 31–54 (2016).10.13189/ujc.2016.040201 ↗
4. F. Tietz, H.-P. Buchkremer, and D. Stover, “Components manufacturing for solid oxide fuel cells,” Sol. St. Ionics, 152–153, 373–381 (2002)10.1016/S0167-2738(02)00344-2 ↗
5. H. L. Frandsen, T. Ramos, A. Faes, et al., “Optimization of the strength of SOFC anode supports,” J. Europ. Ceram. Soc., 32, No. 5, 1041–1052 (2012).10.1016/j.jeurceramsoc.2011.11.015 ↗
6. D. Kennouche, Y. Chen-Wiegart, K. Yakal-Kremski, et al., “Observing the microstructural evolution of Ni- Yttria-stabilized zirconia solid oxide fuel cell anodes,” Acta Mater., 103, 204–210 (2016).10.1016/j.actamat.2015.09.055 ↗
7. D. Jung, H. Park, K.-S. Moon, et al., “Effect of microstructure on the electrochemical performance of Ni– ScSZ anodes,” Ceram. Int., 42, No. 10, 11757–11765 (2016).10.1016/j.ceramint.2016.04.096 ↗
8. A. Sarikaya and F. Dogan, “Effect of various pore-forming agents on the microstructural development of tape-cast porous ceramics,” Ceram. Int., 39, 403–413 (2013).10.1016/j.ceramint.2012.06.041 ↗
9. A. Sanson, P. Pinasco, and E. Roncari, “Influence of pore-forming agents on slurry composition and microstructure of tape cast supporting anodes for SOFCs,” J. Europ. Ceram. Soc., 28, 1221–1226 (2008).10.1016/j.jeurceramsoc.2007.10.001 ↗
10. B. A. Horri, C. Selomulya, and H. Wang, “Characteristics of Ni/YSZ ceramic anode prepared using carbon microspheres as a pore-forming agent,” Int. J. Hydr. Energy, 37, 15311–15319 (2012).10.1016/j.ijhydene.2012.07.108 ↗
11. M. Sharif, F. Golestani, E. Khatibi, et al., “Dispersion and stability of carbon black nanoparticles, studied by ultraviolet–visible spectroscopy,” J. Taiwan Inst. Chem. Eng., 40, 524–527 (2009).
12. M. Kim, J. Lee, and J.-H. Han, “Fabrication of anode support for solid oxide fuel cell using zirconium hydroxide as a pore-forming agent,” J. Power Sources, 196, 2475–2482 (2011).10.1016/j.jpowsour.2010.10.109 ↗
13. O. Vasylyev, I. Brodnikovskyi, M. Brychevskyi, et al., “NiO–10Sc1CeSZ anode: structure and mechanical behavior,” Adv. Solid Oxide Fuel Cells III: Ceram. Eng. Sci. Proc., 28, 361–377 (2007).
14. A. D. Vasil’ev, G. Ya. Akimov, and A. Yu. Koval’, “Zirconia ceramics and its prospects in Ukraine,” Ogneup. Tekh. Keram., No. 10, 2–5 (2000).
15. B. S. Prakash, S. S. Kumar, and S. T. Aruna, “Properties and development of Ni/YSZ as an anode material in solid oxide fuel cell: A review,” Ren. Sust. Energy Reviews, 36, 149–179 (2014).10.1016/j.rser.2014.04.043 ↗
16. B. A. Horri, C. Selomulya, and H. Wang, “Characteristics of Ni/YSZ ceramic anode prepared using carbon microspheres as a pore-forming agent,” Int. J. Hyd. Energy, 37, 15311–15319 (2012)10.1016/j.ijhydene.2012.07.108 ↗
17. L. D. Landau and E. M. Lifshits, Electrodynamics of Continuous Media [in Russian], Gostekhizdat, Moscow (1957), p. 616.
18. V. I. Odeldevskii, “Calculating the generalized conductivity of heterogenous systems,” Zhur. Tekh. Fiz., 21, No. 6, 667–677 (1951).
19. V. V. Skorokhod, “About electrical conductivity of disperse mixtures of non-conductors with conductors,” Inzh. Fiz. Zhur., 2, No. 8, 51–58 (1959).
20. S. Kim, H. Moon, and S. Hyun, “Ni–YSZ cermet anode fabricated from NiO–YSZ composite powder for high-performance and durability of solid oxide fuel cells,” Sol. St. Ionics, 178, 1304–1309 (2007).10.1016/j.ssi.2007.06.014 ↗
21. Y. Brodnikovskyi, B. Vasyliv, V. Podhurska, et al., “Influence of reduction conditions of NiO on its mechanical and electrical properties,” J. Electrochem. Sci. Eng., 6, No. 1, 113–121 (2016).
22. GOST 2409–2014, Refractories. Method for Determining Apparent Density, Open and Total Porosity, and Water Absorption [in Russian], Standartinform, Moscow (2014).
23. A. Borger, P. Supancic, and R. Danzer, “The ball on three balls test for strength testing of brittle discs – stress distribution in the disc,” J. Europ. Ceram. Soc., 22, 1425–1436 (2002).10.1016/S0955-2219(01)00458-7 ↗
24. R. Danzer, W. Harrer, and P. Supancic, “The ball on three balls test: strength and failure analysis of different materials,” J. Europ. Ceram. Soc., 27, 1481–1485 (2007).10.1016/j.jeurceramsoc.2006.05.034 ↗
25. M. Andrzejczuk, O. Vasylyev, I. Brodnikovskyi, et al., “Microstructural changes in NiO–ScSZ composite following reduction processes in pure and diluted hydrogen,” Mater. Characteriz., 87, 159–165 (2014).
26. A. D. Vasilev and S. A. Firstov, “Toughening by pores,” in: Advanced Multi Layered Fiber-Reinforced Composites, Kluwer Academic Publishers, London (1998), pp. 371–384.10.1007/978-94-007-0868-6_24 ↗