Stability and Heat Resistance of Silicide Coatings on Refractory Metals. Part 2. Stability and Heat Resistance of Silicide Coatings on Tungsten and Molybdenum at 1500-2000°C
Source abstract
Abstract
The kinetics of diffusion redistribution of phases within the system WSi2 ― W on heating tungsten silicide in air in the temperature range 1500-2000°C is studied. The stability and heat resistance of silicide coatings on tungsten is mainly governed by the diffusion of silicon towards the interphase boundaries W ― W5Si3, W5Si3 ― WSi2, and WSi2 ― SiO2, formation at them of diffusion barriers of lower silicide W5Si3, and also a protective SiO2 film at the outer boundary of the silicide coating. It is established that the transition rate for the higher to the lower tungsten silicide WSi2 → W5Si3 is on average four times slower than the transition rate for MoSi2 → Mo5Si3. It is shown that an increase in silicon concentration in the WSi2 surface layer stimulates formation of diffusion barrier compounds at interphase boundaries. This leads to an increase in the stability of the phase composition and heat resistance of a silicide coating on metals. In particular at 1700°C the transition rate for molybdenum silicide on tungsten MoSi2 → (Mo, W)5Si3 is about twenty times slower than the transition rate for MoSi2 → Mo5Si3, and less by a factor of about eleven than the transition rate for WSi2 → W5Si3. Here there is also an increase in the heat resistance of silicide coatings on tungsten and molybdenum. It is shown that the SiO2 film on tungsten silicide does not lose its protective properties up to 2000°C.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Intermetallics and Advanced Alloy Properties · Material Properties and Applications · Semiconductor materials and interfaces
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (12)
Show source-provided references
1. V. I. Zmii and N. V. Kovtun, “Stability and heat resistance of silicide coatings on refractory metals. I. Effect of surface layer on phase redistribution in the system WSi2 - W,” Poroshk. Metall., Nos. 7–8, 70–74 (2002).
2. V. I. Zmii, “Preparation of diffusion silicide coatings of prescribed composition,” Poroshk. Metall., Nos. 11–12, 65–68 (1995).
3. Yu. V. Dzyadykevich, “Structure formation during high-temperature oxidation of a borosilicide coating,” Fiz. Khim. Obrab. Materialov, 5, 61–64 (1984).
4. E. P. Nechiporenko, A. P. Petrichenko, and E. N. Kon'shin, “Effect of molybdenum disilicide protective coating thickness on maximum heater operating temperature,” in: Anticorrosion Coatings [in Russian], Nauka, Leningrad (1983).
5. A. V. Kasatkin and I. V. Matvienko, “Heat resistance of silicide coatings on molybdenum and its alloys,” Izv. RAN, Neorgan. Materialy, 30, No. 7, 92–93 (1994).
6. N. I. Polyakov, V. T. Gritsina, V. I. Zmii, and V. I. Tsyganok, “Kinetics of phase redistribution in the system Mo- MoSi2 under loading conditions,” Fiz. Khim. Obrab. Materialov, 4, 71–74 (1981).
7. V. E. Ivanov, E. P. Nechiporenko, V. I. Zmii, and V. M. Krivoruchko, “High-temperature oxidation of tungsten disilicide at 1500–1800°C,” Izv. Akad. Nauk SSSR, Neorgan. Materialy, 1, No. 8, 1360–1363 (1965).
8. V. E. Ivanov, E. P. Nechiporenko, L. N. Efimenko, and M. I. Yurchenko, Protection of Tungsten from Oxidation at High Temperature [in Russian], Atomizdat, Moscow (1968).
9. V. I. Zmii, L. N. Efimenko, N. S. Poltavtsev, and I. A. Snezhko, “Oxidation of tungsten disilicide prepared by vacuum activation siliciding,” Zashch. Metall., 1, 141–143 (1984).
10. M. S. Tsirlin and M. S. Alergant, “Thermodynamic aspects of high-temperature oxidation of refractory metal silicides,” in: Corrosion-Resistant Coatings [in Russian], Nauka, St. Petersburg (1992).
11. Yu. V. Dzyadykevich, “Study of the compatibility of borosilicide coatings with refractory metals,” Izv. Akad. Nauk SSSR, Metally, 3, 182–187 (1977).
12. Yu. P. Zotov, A. D. Davydova, N. N. Kroshkina, et al., “Study of the reaction of silicide and borosilicide coatings based on WSi2 with a tungsten substrate and evaluation of their operating eficiency in air at elevated temperature,” Izv. Akad. Nauk SSSR, Neorgan. Materialy, 14, No. 5, 879–883 (1978).