journal article·2016-09

Effect of Ni3Al Addition and Heating Mode on the Electrochemical Response on Austenitic and Ferritic Stainless Steels

A. Raja Annamalai, A. Upadhyaya, D. Agrawal

Powder Metallurgy and Metal Ceramics· Volume 55· Issue 5-6
Publisher page

Abstract

The effect of intermetallic Ni3Al addition and heating mode on the electrochemical behavior of sintered austenitic (316L) and ferritic (434L) stainless steels is studied. The green compacts were sintered by conventional and microwave methods in solid state at 1350°C in H2 for a period of 60 min. The sintered samples were then subjected to several characterization techniques for evaluating their density and hardness, and finally their electrochemical response was evaluated through potentiodynamic polarization scan (1 mV/sec) in 0.1 N H2SO4. Upon addition of nickel aluminide, there was an increase in the densification of the composites, which was found more pronounced in case of 434L stainless steel with nickel-aluminide dispersoid composites. A positive response was also observed on the corrosion resistance of the composites as compared with the bare stainless steel compacts.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. J. Shankar, A. Upadhyaya, and R. Balasubramaniam, “Electrochemical Behavior of Sintered Oxide Dispersion Strengthened Stainless Steels,” Corros. Sci., 46, No. 2, 487–492 (2004).10.1016/S0010-938X(03)00144-6 ↗
2. E. Otero, A. Pardo, E. Saenz, et al., “Corrosion behaviour of AISI 304L and 316L stainless steels prepared by powder metallurgy in the presence of sulphuric and phosphoric acid,” Corros. Sci., 40, No. 8, 1421–1434 (1998).10.1016/S0010-938X(98)00047-X ↗
3. R. M. German, Powder Metallurgy Science, Metal Powder Industries Federation, New Jersey, USA (1994).
4. R. M. German, “Supersolidus liquid-phase sintering of prealloyed powders,” Metall. Mater. Trans. A., 28, 1553–1567 (1997).10.1007/s11661-997-0217-0 ↗
5. F. Velasco, N. Anton, J. M. Torralba, and J. M. Ruiz-Prieto, “Mechanical and Corrosion Behavior of Powder-Metallurgy Stainless-Steel Based Metal-Matrix Composites,” Mater. Sci. Technol., 13, Issue 10, 847–851 (1997).10.1179/mst.1997.13.10.847 ↗
6. S. N. Patankar and M. J. Tan, “Role of reinforcement in sintering of SiC/316L stainless steel composite,” Powder Metall., 43, No. 4, 350 (2000).10.1179/003258900666078 ↗
7. J. Jain, A. M. Kar, and A. Upadhyaya, “Effect of YAG addition on sintering of P/M 316L and 434L stainless steels,” Mater. Lett., 58, 2037–2040 (2004).10.1016/j.matlet.2003.12.022 ↗
8. J. Shankar, A. Upadhyaya, and R. Balasubramaniam, “Supersolidus liquid phase sintering of austenitic stainless steel–yttria composites,” in: Advances in Powder Metallurgy Particulate Materials 2002, Vol. 13, Metal Powder Industries Federation, Princeton, New Jersey, USA (2202), pp. 313–322.
9. P. Jackson, C. C. Degnan, and J. V. Wood, “Reactive sintering of 316L stainless steel by the formation of a nickel aluminide liquid phase,“ in: Proc. EUROMAT—Materials Development and Processing, Vol. 8, Wiley VCH, London (1999), pp. 229–236.
10. F. Velasco, W. M. Lima, N. Anton, et al., “Effect of intermetallic particles on wear behaviour of stainless steel matrix composites,” Tribol. Int., 36, 547 (2003).10.1016/S0301-679X(02)00264-5 ↗
11. Properties and Selection: Irons, Steels, and High-Performance Alloys, ASM Handbook, Vol. 1, ASM International (1990), pp. 1326.
12. R. D. Peelamedu, R. Roy, and D. Agrawal, “Anisothermal reaction synthesis of garnets, ferrites, and spinels in microwave field,” Mater. Res. Bull., 36, 2723–2739 (2001).10.1016/S0025-5408(01)00743-7 ↗
13. R. Roy, Y. Fang, J. Cheng, and D. K. Agrawal, “Decrystallizing solid crystalline titania, without melting, using microwave magnetic fields,” J. Amer. Ceram. Soc., 88, No. 6, 1640–1642 (2005).10.1111/j.1551-2916.2005.00261.x ↗
14. S. Balaji, G. Joshi, and A. Upadhyaya, “Corrosion behavior of sintered aluminide reinforced ferritic stainless steels,” Scripta Mater., 56, 149–151 (2007).10.1016/j.scriptamat.2006.09.030 ↗
15. S. Balaji and A. Upadhyaya, “Electrochemical behavior of sintered YAG dispersed 316L stainless steel composites,” Mater. Chem. Phys., 101, Nos. 2–3, 310–316 (2007).10.1016/j.matchemphys.2006.06.002 ↗
16. J. Abenojar, F. Velasco, J. M. Torralba, et al., “Reinforcing 316L stainless steel with intermetallic and carbide particles,” Mater. Sci. Eng. A., 335, 1–5 (2002).10.1016/S0921-5093(01)01941-4 ↗
17. S. K. Mukherjee and G. S. Upadhyaya, “Sintering of 434L ferritic stainless steel containing Al2O3 particles,” Int. J. Powder Metall. Powder Technol., 19, 289–294 (1983).
18. M. C. Baran and B. A. Shaw, “Corrosion modes in P/M ferritic stainless steels,” Int. J. Powder Metall., 36, No. 4, 57–68 (2000).