journal article·2020-09

Nitriding of Sintered VT1-0 Titanium Alloy

A. G. Luk’yanenko, I. M. Pohrelyuk, Kh. S. Shlyakhetka, A. A. Skrebtsov, T. M. Kravchyshyn

Powder Metallurgy and Metal Ceramics· Volume 59· Issue 5-6
Publisher page

Abstract

Components produced from sintered titanium alloys are increasingly used in mechanical engineering but need to be protected for operation in corrosive environments because of porosity. Nitriding is one of the effective protection methods. The objective of the study was to analyze the nitriding kinetics of a sintered VT1-0 titanium alloy at atmospheric (105 Pa) and reduced (1 Pa) nitrogen pressure at 800, 850, and 900°C for 5, 10, and 20 h versus a wrought titanium alloy of the same composition. The study employed discrete gravimetry, hardness measurement, optical and electronic metallography, profilometry, and X-ray diffraction. The nitriding kinetics of the VT1-0 titanium alloy sintered from titanium powder alone and from a mixture of titanium and titanium hydride powders was studied in comparison with wrought titanium. Under the nitriding parameters in question, the weight gain of all samples was described by a parabolic law and the weight gain of the sintered samples was higher than that of the wrought ones. The kinetic parameters of nitriding for the sintered and wrought VT1-0 titanium alloys were determined for the first time in the test temperature–time and gas dynamic conditions. Changes in the surface and near-surface layers depending on metal porosity were shown. After nitriding, the surface microhardness of the sintered titanium was lower than that of the wrought titanium samples because of porosity, and the strengthened surface layer was thicker. The nitride film formed on the sintered titanium alloy was thinner and less distorted than that on the wrought titanium alloy. The results can be used to develop nitriding conditions for sintered VT1-0 titanium products.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Titanium Alloys Microstructure and Properties · Advanced materials and composites · Metal and Thin Film Mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. F.H. (Sam) Froes, “8. Powder metallurgy of titanium alloys,” in: I. Chang and Y. Zhao (eds.), Advances in Powder Metallurgy: Properties, Processing and Applications, Woodhead Publishing Series in Metals and Surface Engineering, Woodhead Publishing Limited (2013), pp. 202–357, DOI: 10.1533/9780857098900.2.202.10.1533/9780857098900.2.202 ↗
2. Z.Z. Fang, J.D. Paramore, P. Sun, K.S.R. Chandran, Y. Zhang, Y. Xia, F. Cao, M. Koopman, and M. Free, “Powder metallurgy of titanium—past, present, and future,” Int. Mater. Rev., 407–459 (2017), DOI: https://doi.org/10.1080/09506608.2017.1366003 .10.1080/09506608.2017.1366003 ↗
3. V.A. Boguslaev, P.D. Zhemanyuk, A.V. Ovchinnikov, Z.V. Lekhovitser, and I.O. Bykov, “Use of titanium powders to produce gas turbine engine parts by powder metallurgy methods,” Aviats. Kosm. Tekh. Tekhnol., No. 9, 86–91 (2017).
4. O.M. Ivasishin, D.G. Savvakin, K.A. Bondareva, V.S. Mokson, and V.A. Duz, “Production of titanium alloys and components by cost-effective powder metallurgy approach for wide industrial application,” Nauka Innovats., 1, No. 2, 44–57 (2005).10.15407/scin1.02.044 ↗
5. A.A. Hidalgo, R. Frykholm, T. Ebel, and F. Pyczak, “Powder metallurgy strategies to improve properties and processing of titanium alloys: A review,” Adv. Eng. Mater. (2017), DOI: https://doi.org/10.1002/adem.201600743 .10.1002/adem.201600743 ↗
6. I.M. Pogrelyuk, O.V. Ovchinnikov, A.A. Skrebtsov, Kh.S. Shvachko, R.V. Proskurnyak, and S.M. Lavrys, “Corrosion properties of titanium produced by powder metallurgy technique,” Fiz. Khim. Mekh. Mater., 52, No. 5, 88–92 (2016).
7. A. Bautista, C. Moral, G. Blanco, and F. Velasco, “Influence of sintering on the corrosion behavior of a Ti– 6Al–4V alloy,” Mater. Corros., 56, No. 2, 98–103 (2005).10.1002/maco.200403818 ↗
8. O.V. Ovchinnikov, I.M. Pogrelyuk, A.A. Skrebtsov, R.V. Proskurnyak, and Kh.S. Shvachko, “Corrosion resistance of VT1-0 titanium and ways for its improvement,” Nov. Mater. Tekhnol. Metall. Mashynobud., No. 1, 20–25 (2014).
9. V.M. Fedirko and I.M. Pogrelyuk, Nitriding of Titanium and Its Alloys [in Ukrainian], Naukova Dumka, Kyiv (1995), p. 220.
10. V.A. Belous, G.I. Nosov, and I.O. Klimenko, “Strengthening of titanium alloys by plasma ion nitriding,” Vopr. Atom. Nauki Tekh., No. 5, 73–82 (2017).
11. A. Zhecheva, W. Sha, S. Malinov, and A. Long, “Enhancing the microstructure and properties of titanium alloys through nitriding and other surface engineering methods,” Surf. Coat. Technol., 200, 2192–2207 (2005).10.1016/j.surfcoat.2004.07.115 ↗
12. V.G. Khizhnyak, M.M. Bobina, and O.M. Solovar, “Wear-resistant nitrogen-base coatings on VT9 alloy,” Probl. Tert. Znosh., No. 1, 61–66 (2013).
13. B. Januszewicz and L. Klimek, “Nitriding of titanium and Ti6Al4V alloy in ammonia gas under low pressure,” Mater. Sci. Technol., 26, No. 5, 586–590 (2010).10.1179/174328409X448501 ↗
14. D.S. Vershinin and M.Yu. Smolyakova, “Effect of the gas mixture composition on the structure and properties of the VT6 titanium alloy in low-temperature nitriding,” Poverkhn. Rentgen. Sinkhrotron. Neytron. Issled., No. 2, 68–73 (2012).
15. N.G. Krashennikova, V.I. Kapranova, S.Ya. Alibekov, and R.S. Salmanov, “Chemical and heat treatment of iron-base structural powder materials,” Vest. Tekhnol. Univ., 18, No. 8, 125–127 (2015).
16. E. Fromm and E. Gebhardt, Gases and Carbon in Metals, Springer-Verlag, Berlin (1976).