Features of Brittle Material Powder Compaction During Pressing
Source abstract
Abstract
The compaction of (i) titanium, vanadium, and molybdenum carbide powders, (ii) mixtures of these powders with the addition of nickel, chromium, and niobium carbide powders, and (iii) coarse titanium and tungsten carbides as well as diamond powders clad with cobalt under compressive loading with a constant rate on the powder in a die at room temperature is studied. Based on the variation of the relative density of the compacts with current pressure, the variation of stresses in the matrix (forming a porous body) with its strain is determined. This enables to reveal the features of compaction, strain hardening, and fracture of brittle powder particles during pressing. It is established that for the molybdenum carbide powder, consisting of powder particles with pronounced irregular shape, the initial elastic deformation of the matrix abruptly transits into the stage of plastic deformation with almost linear strain hardening. At the final stage of the powder compaction, the particles are fractured. At the initial stage of pressing, an increase in the packing density of the powder particles and in their strain hardening occurs for titanium and vanadium carbide powders, whose particle shape is close to the rounded. With the increase in the density of the porous body, it is observed an almost linear strain hardening of the matrix, which changes into decay with decreasing shear stress, when the powder body approaches its non-porous state. As a result of pressing, the size of the coherent X-ray scattering areas decreased to 62 nm and the dislocation density in the titanium carbide particles grew to 8.3 · 1010 cm–2. With an increasing content of plastic metallic particles in the matrix with the particles of brittle materials, it is the metallic particles that predominantly undergo the plastic strain with strain hardening. This causes a sharp increase in the total strain hardening, reducing the density of the porous body during pressing. It is established an effective compacting of coarse titanium and tungsten carbide powders with cobalt-clad particles 200–600 μm in size. In this case the variation of the stress in the matrix with the strain of the matrix has a sharp yield point associated with high elastic limit, significantly exceeding the yield stress, and the time delay in the transition from a purely elastic deformation of the body to its plastic flow.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · Powder Metallurgy Techniques and Materials · Injection Molding Process and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. R. L Hewitt, W. Wallace, and M. C. De Malherbe, “The effect of strain-hardening in powder compaction,” Powder Metal., 16, No. 31, 88–106 (1973).10.1179/pom.1973.16.31.005 ↗
2. R. L. Hewitt, W. Wallace, and M. C. De Malherbe, “Plastic deformation in metal powder compaction,” Powder Metal., 17, No. 33, 1–12 (1974).10.1179/pom.1974.17.33.001 ↗
3. A. I. Otrok, “Deformation strengthening of the matrix in the rolling of heterogeneous powder mixtures,” Powder Metall. Met. Ceram., 12, No. 12, 947–950 (1973).10.1007/BF00791733 ↗
4. I. F. Martynova, V. V. Skorokhod, and S. M. Solonin, “Plastic deformation in the pressing of powders of ductile metals,” Powder Metall. Met. Ceram., 13, No. 3, 205–209 (1974).10.1007/BF00790636 ↗
5. M. S. Kovalchenko, “Strain hardening of a porous body in pressing,” Powder Metall. Met. Ceram., 48, Nos. 3–4, 133–144 (2009).10.1007/s11106-009-9118-7 ↗
6. A. K. Radchenko, M. S. Kovalchenko, and D. N. Brodnikovskii, “Compaction and strain hardening of metal powders and their mixtures when pressed,” Powder Metall. Met. Ceram., 48, Nos. 5–6, 267–273 (2009).10.1007/s11106-009-9134-7 ↗
7. O. A. Katrus, Yu. G. Tkachenko, G. S. Oleinik, et al., “Influence of rolling on the structure and properties of aluminum-nitride powder and hot-pressed material produced therefrom. I. Powders,” Powder Metall. Met. Ceram., 31, No. 3, 226–229 (1992).10.1007/BF01159015 ↗
8. O. A. Katrus, Yu. G. Tkachenko, G. S. Oleinik, et al., “Influence of rolling on the structure and properties of aluminum-nitride powder and hot-pressed material obtained therefrom. II. Polycrystalline materials,” Powder Metall. Met. Ceram., 31, No. 5, 420–423 (1992).10.1007/BF00796251 ↗
9. M. V. Luchka, Scientific and Practical Basis for the Formation of Wear-Resistant Composite Coatings by Galvanic Powder Gradient Hardening for Critical Friction Conditions [in Ukrainian], DSci Thesis, sp. 05.02.01, Kyiv (2013), p. 44.
10. J. K. Beddow (Ed.), Particle Characterization in Technology, Vol. 1. Microanalysis, CRC Press, Boca Raton, Florida, USA (1984), p. 240.
11. J. K. Beddow (Ed.), Particle Characterization in Technology, Vol. 2. Morphological Analysis, CRC Press, Boca Raton, Florida, USA (1984), p. 265.
12. H. S. Hundal, S. Rohani, H. C. Wood, and M. N. Pons, “Particle shape characterization using image analysis and neural networks,” Powder Technol., 91, No. 3, 217–227 (1997).10.1016/S0032-5910(96)03258-5 ↗
13. G. M. Fikhtengolts, A Course in Differential and Integral Calculations [in Russian], Vol. 3, Fizmatgiz, Moscow (1960), pp. 563–573.
14. V. I. Smirnov, A Course of Higher Mathematics [in Russian], Vol. 2, Gostekhteorizdat, Moscow (1956), pp. 424–430.
15. A. Angot, Supplements of Mathematics for Use by Engineers of Electrotechnics and Telecommunications, 6th ed. [in French], Masson, Paris (1972), p. 869.
16. M. S. Kovalchenko, “Rheological models of pressure sintering of powders,” Powder Metall. Met. Ceram., 52, Nos. 1–2, 7–19 (2013).10.1007/s11106-013-9490-1 ↗
17. R. M. German, Particle Packing Characteristics, Metal Powder Industries Federation, Princeton (1989), p. 443.
18. A. M. Nikolenko, “Hierarchic material structure,” Powder Metall. Met. Ceram., 41, Nos. 5–6, 317–334 (2002).10.1023/A:1020547802602 ↗
19. R. Honeycomb, Plastic Deformation of Metals [Russian translation] Mir, Moscow (1972), p. 408.
20. J. Friedel, Dislocations, 1st edition, Pergamon Press, Oxford (1964), p. 490.
21. JCPDS, Powder Diffraction File, Alphabetical Index, Inorganic Compounds, International center for diffraction data, PA, USA, 1977.
22. I. N. Kachanov and L. I. Mirkin, X-ray Diffraction Analysis of Polycrystals [in Russian], Mashgiz, Moscow (1960), p. 214.
23. G. K. Williamson and K. E. Smallman, “Metallurgy division,” Philos. Mag., 1, No. 1, 34–39 (1956).10.1080/14786435608238074 ↗
24. M. S. Kovalchenko, “Dynamics of uniaxial stretching of viscoelastic strain-hardened body in the single-degree-of-freedom system. I. The system prescribed motion,” Probl. Proch., No. 4, 16–27 (1998).
25. N. A. Umov, Equations of Motion of Energy. Selected Studies [in Russian], Gostekhteorizdat, Moscow (1950), pp. 151–200.
26. J. J. Rushchitsky and S. I. Tsurpal, Waves in Materials with Microstructure [in Ukrainian], S. P. Timoshenko Institute of Mechanics of NAS of Ukraine, Kyiv (1998), p. 377.