journal article·2008-11

Dependence of antifriction properties of self-lubricating copper-based composite on the elastoplastic characteristics of tribosynthesis region

A. G. Kostornov, O. I. Fushchich, V. F. Gorban’, T. M. Chevychelova, A. D. Kostenko

Powder Metallurgy and Metal Ceramics· Volume 47· Issue 11-12
Publisher page

Abstract

Microindentation is used to examine the elastoplastic deformation of a self-lubricating copper-based antifriction composite. Its performance and wear resistance in high vacuum and in open air are studied. It is shown that the friction skin synthesized during sliding in vacuum differs from the original material not only in the phase and chemical composition, but also in the structural state and mechanical characteristics: it has high hardness and is very susceptible to stress relaxation. The self-organization of the skin in the friction region leads to the self-lubrication effect and thus to low friction coefficient, high wear resistance, and good performance of the tribosystem in vacuum as a whole. It is established that the susceptibility of the friction skin synthesized in open air to stress relaxation is insignificant because of lead oxidation and thus its lubricating properties decrease as well. The wear resistance of the material decreases and the wear rate and friction coefficient increase in friction in open air.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Tribology and Wear Analysis · Polymer Science and Applications · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (8)

Show source-provided references
1. A. G. Kostornov, O. I. Fushchich, T. M. Chevichelova, and Yu. M. Simeonova, Self-lubricating Antifriction Copper-Based Composite Material [in Ukrainian], Patent 77601 Ukraine, publ. December 15 (2006).
2. A. G. Kostornov, O. I. Fushchich, T. M. Chevychelova, et al., “Friction, wear, and targeted synthesis of rubbing surfaces of self-lubricating composites,” Powder Metall. Met. Ceram., 46, No. 3–4, 111–117 (2007).10.1007/s11106-007-0018-4 ↗
3. B. I. Kostetskii, A. K. Karaulov, N. B. Kostetskaya, and V. S. Ryzhov, “Structure of friction surface,” Metallofizika, 65, 46–59 (1976).
4. I. M. Fedorchenko, “Modern theories of the mechanism of friction and wear and the main trends in the development of composite frictional and bearing materials — A review,” Powder Metall. Met. Ceram., 18, No. 4, 256–265 (1979).10.1007/BF00793812 ↗
5. V. F. Gorban’, “Properties of secondary structures in metals and coatings,” Metallofiz. Noveish. Tekhnol., 5, No. 11, 1527–1535 (2007).
6. A. G. Kostornov, J. M. Simeonova, O. I. Fushchich, et al., “Effect of factors governing dry friction on structure formation for the tribological synthesis zone in composites based on copper” Powder Metall. Met. Ceram., 45, No. 3–4, 109–213 (2006).
7. A. G. Kostornov Yu. M, Simeonova, O. I. Fushchich, et al., “Determining influence of the tribosynthesis of new structures in the friction region on the performance of antifriction materials,” in: Problems of Friction and Wear [in Ukrainian], Issue 46, Nats. Aviats. Univ., Kyiv (2006), pp. 109–121.
8. S. A. Firstov, V. F. Gorban’, É. P. Pechkovskii, and N. A. Mameka, “Indentation equation,” Dop. NAN Ukrainy, No. 12, 100–106 (2007).