journal article·2018-01

Base Alloy Concept in the Development of High-Entropy Materials

M. O. Krapivka, O. M. Myslyvchenko, M. V. Karpets

Powder Metallurgy and Metal Ceramics· Volume 56· Issue 9-10
Publisher page

Abstract

The requirements to be met by a high-entropy alloy to be used as a base one for the development of new high-entropy materials have been formulated. Four alloys that comply with these requirements were selected. The use of CrMnFeCoNi alloy with an fcc lattice as a base one was analyzed, considering that this alloy has been the most extensively studied and has adequate ductility. The influence of 12 elements (Al, Ti, Zr, Hf, V, Nb, Ta, Mo, W, Re, Cu, Y) on the phase composition of the base alloy at the equiatomic content of each additive was studied. The maximum solubility of each element in the base alloy was determined. It is found that doping of the base alloy allows the bcc, B2, σ, μ, χ, and C14 and C15 Laves phases to be obtained. The feasibility of using the base alloy to develop new high-entropy materials with the approaches applied to develop conventional alloys is shown.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High Entropy Alloys Studies · High-Temperature Coating Behaviors · Additive Manufacturing Materials and Processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. A. A. Antonysamy, P. B. Prangnell, and J. Meyer, “Effect of wall thickness transitions on texture and grain structure in additive layer manufacture (ALM) of Ti–6Al–4V,” Mater. Sci. Forum, Trans. Tech. Publ., 706, 205–210 (2012).10.4028/www.scientific.net/MSF.706-709.205 ↗
2. J. W. Yeh, Y. L. Chen, and S. J. Lin, “High-entropy alloys—a new era of exploitation,” Mater. Sci. Forum, Trans. Tech. Publ., 560, 1–9 (2007).10.4028/www.scientific.net/MSF.560.1 ↗
3. G. Sheng and C. T. Liu, “Phase stability in high entropy alloys: formation of solid-solution phase or amorphous phase,” Prog. Nat. Sci. Mater. Int. J., No. 21, 433–446 (2011).
4. Y. Zhang and W. Peng, “Microstructural control and properties optimization of high-entropy alloys,” Proc. Eng. J., 27, 1169–1178 (2012).10.1016/j.proeng.2011.12.568 ↗
5. O. N. Senkov, J. D. Miller, D. B. Miracle, et al., “Accelerated exploration of multi-principal element alloys with solid solution phases,” Nat. Commun., 6, 1–6 (2015).10.1038/ncomms7529 ↗
6. N. A. Krapivka, S. A. Firstov, M. V. Karpets, et al., “Phase formation and structurization in high-entropy AlCrFeCoNiCu x alloys (x = 0, 0.5, 1.0, 2.0, 3.0),” Fiz. Met. Metalloved., No. 5, 496–504 (2015).
7. M. V. Karpets, O. M. Myslyvchenko, O. S. Makarenko, et al., “Properties of multicomponent high-entropy copper-doped AlCrFeCoNi alloy,” Probl. Tert. Znosh., No. 2, 103–111 (2014).
8. M. V. Karpets, O. M. Myslyvchenko, O. S. Makarenko, et al., “Effect of nickel on the structure and phase composition of high-entropy VCrMnFeCoNi x alloy,” Sverkh. Tverd. Mater., No. 3, 52–60 (2015).
9. M. V. Karpets, O. M. Myslyvchenko, O. S. Makarenko, et al., “Mechanical properties and formation of phases in high-entropy CrFeNiCuCoAl x alloys,” Powder Metall. Met. Ceram., 54, No. 5–6, 344–352 (2015).10.1007/s11106-015-9720-9 ↗
10. V. F. Gorban, M. V. Karpets, O. M. Myslyvchenko, et al., “Effect of Co on the phase composition, microstructure, and mechanical properties of high-entropy AlCrFeNiCuCox alloy,” Visn. Ukr. Materialoznav. Tov., No. 7, 99–106 (2014).
11. M. V. Karpets, O. M. Myslyvchenko, O. S. Makarenko, et al., “Microstructure and mechanical properties of high-entropy AlCrCoNiCuFe x alloy,” Fiz. Khim. Tverd. Tela, No. 3, 661–665 (2014).
12. M. C. Gao and D. E. Alman, “Searching for next single-phase high-entropy alloy composition,” Entropy, 15, No. 10, 4504–4519 (2013).10.3390/e15104504 ↗
13. B. Cantor, I. T. H. Chang, P. Knight, et al., “Microstructural development in equiatomic multicomponent alloys,” Mater. Sci. Eng. A, 375, 213–218 (2004).10.1016/j.msea.2003.10.257 ↗
14. O. N. Senkov, J. M. Scotta, S. V. Senkova, et al., “Microstructure and room temperature properties of a high-entropy TaNbHfZrTi alloy,” J. Alloys Compd., 509, No. 20, 6043–6048 (2011).10.1016/j.jallcom.2011.02.171 ↗
15. S. A. Firstov, T. G. Rogul, N. A. Krapivka, et al., “Effect of crystallization rate on the structure, phase composition, and hardness of high-entropy AlTiVCrNbMo alloy,” Deform. Razrush. Mater., No. 10, 8–15 (2013).
16. O. N. Senkov, G. B. Wilks, J. M. Scott, et al., “Mechanical properties of Nb25Mo25Ta25W25 and V20Nb20Mo20Ta20W20 refractory high entropy alloys,” Intermetallics, 19, No. 5, 698–706 (2011).10.1016/j.intermet.2011.01.004 ↗
17. F. Otto, Y. Yang, H. Bei, et al., “Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys,” Acta Mater., 61, No. 7, 2628–2638 (2013).10.1016/j.actamat.2013.01.042 ↗
18. K. Y. Tsai, M. H. Tsai, and J. W. Yeh, “Sluggish diffusion in Co–Cr–Fe–Mn–Ni high-entropy alloys,” Acta Mater., 61, No. 13, 4887–4897 (2013).10.1016/j.actamat.2013.04.058 ↗
19. M. V. Karpets, E. S. Makarenko, A. N. Myslyvchenko, et al., “High-temperature diffractometer analysis of FeCoNiMnCr alloy oxidation,” Metallofiz. Noveish. Tekhnol., 36, No. 6, 829–840 (2014).10.15407/mfint.36.06.0829 ↗
20. M. O. Krapivka, Yu. P. Mazur, M. P. Semenko, et al., “Structure of high-entropy CrMnFeCoNi and CrMnFeCoNi2Cu alloys and thermal stability of their electric transport properties,” Metallofiz. Noveish. Tekhnol., 37, No. 6, 731–740 (2015).10.15407/mfint.37.06.0731 ↗
21. F. Otto, A. Dlouhý, C. Somsen, et al., “The influences of temperature and microstructure on the tensile properties of a CoCrFeMnNi high-entropy alloy,” Acta Mater., 61, No. 15, 5743–5755 (2013).10.1016/j.actamat.2013.06.018 ↗
22. P. P. Bhattacharjee, G. D. Sathiaraj, M. Zaid, et al., “Microstructure and texture evolution during annealing of equiatomic CoCrFeMnNi high-entropy alloy,” J. Alloys Compd., 587, 544–552 (2014).10.1016/j.jallcom.2013.10.237 ↗
23. L. Patriarca, A. Ojha, H. Sehitoglu, et al., “Slip nucleation in single crystal FeNiCoCrMn high entropy alloy,” Scr. Mater., 112, 54–57 (2016).10.1016/j.scriptamat.2015.09.009 ↗
24. A. Takeuchi and A. Inoue, “Classification of bulk metallic glasses by atomic size difference, heat of mixing and period of constituent elements and its application to characterization of the main alloying element,” Mater. Trans., 46, No. 12, 2817–2829 (2005).10.2320/matertrans.46.2817 ↗
25. S. Singh, N. Wanderka, B. S. Murty, et al., “Decomposition in multi-component AlCoCrCuFeNi highentropy alloy,” Acta Mater., 59, No. 1, 182–190 (2011).10.1016/j.actamat.2010.09.023 ↗
26. J. Y. He, W. Liu, H. Wang, et al., “Effects of Al addition on structural evolution and tensile properties of the FeCoNiCrMn high-entropy alloy system,” Acta Mater., 62, 105–113 (2014).10.1016/j.actamat.2013.09.037 ↗
27. A. Munitz, M. J. Kaufman, J. P. Chandler, et al., “Melt separation phenomena in CoNiCuAlCr high entropy alloy containing silver,” Mater. Sci. Eng. A, 560, 633–642 (2013).10.1016/j.msea.2012.10.007 ↗
28. M. V. Karpets, V. F. Gorban, A. N. Myslyvchenko, et al., “Effect of Ni content on the wear resistance of as-cast high-entropy VCrMnFeCoNi x alloy,” Sovr. Elektrometall., No. 1, 56–60 (2015).