journal article·2020-09

Structure and Wear Resistance of FeNiCrBSiC–MeB2 Electrospark Coatings

M.S. Storozhenko, O.P. Umanskyi, V.B. Tarelnyk, O.Yu. Koval, Yu.V. Gubin, M.O. Mikulina, I.S. Martsenyuk, O.D. Kostenko, T.V. Kurinna

Powder Metallurgy and Metal Ceramics· Volume 59· Issue 5-6
Publisher page

Abstract

The structurization of coatings produced by electrospark deposition (ESD) from the commercial selffluxing FeNiCrBSiC alloy and FeNiCrBSiC-based composites, such as FTB20 (FeNiCrBSiC–20 wt.% TiB2) and FCB20 (FeNiCrBSiC–20 wt.% CrB2), on a steel 45 substrate was studied. The electrospark FeNiCrBSiC coating about 70 μm thick has a globular surface and the FTB20 and FCB20 coatings form a continuous layer up to 50 μm thick over the entire samples. The microhardness does not change across the deposited coating thickness and is 10–14 GPa. The chemical compositions of the ESD coatings and the electrodes are the same, which indicates that the electrode material does not mix with the steel substrate. The structure of the FeNiCrBSiC, FTB20, and FCB20 electrodes and coatings differs significantly because chromium boride and/or titanium boride inclusions refine from 20–25 μm to 1 μm in the ESD process. The heterophase structure of the ESD coatings represents a nickel–iron-base matrix reinforced with fine boride and carboboride particles. The effect of speeds and loads on the wear rate of ESD coatings in dry friction conditions was examined. Electrospark coatings produced from the WC–6% Co hardmetal were tested as wear resistance reference. The wear rate of the FeNiCrBSiC, FTB20, and FCB20 coatings decreases and that of the WC–6% Co coating increases when the speed rises from 4 to 12 m/sec. The wear rate of the ESD coatings becomes one order of magnitude higher when the load increases from 0.1 to 0.4 MPa. Analysis of the friction surfaces showed that wear of the FeNiCrBSiC coating was caused by failure of the globules and that of the FCB20 coating by brittle fracture of the deposited layer. The ESD FTB20 coating has two to three times higher wear resistance than the FeNiCrBSiС coating because of the oxidative wear mechanism whereby protective oxide films develop on the friction surfaces and act as a solid lubricant.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Surface Treatment and Coatings · Advancements in Materials Engineering · Technical Engine Diagnostics and Monitoring

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. K. Holmberg and A. Matthews, Coatings Tribology: Properties, Mechanisms, Techniques and Application in Surface Engineering, Elsevier, Switzerland (2009), 2nd ed., p. 560.
2. M. Cartier, T.A. Polak, and G.D. Wilcox, Handbook of Surface Treatments and Coatings, ASME Press, New York (2003), p. 412.
3. Yu.S. Borisov, Yu.A. Kharlamov, S.A. Sidorenko, and E.N. Arbatovska, Thermal Spray Coatings of Powder Materials: Handbook [in Russian], Tekhnika, Kyiv (1987), p. 544.
4. M.S. Storozhenko, A.P. Umanskii, A.E. Terentiev, and I.M. Zakiev, “Effect of the structure of TiB2–(Fe–Mo) plasma coatings on mechanical and tribotechnical properties,” Powder Metall. Met. Ceram., 56, No. 1–2, 60–69 (2017).10.1007/s11106-017-9872-x ↗
5. G.V. Samsonov and A.D. Verkhoturov, Electrospark Deposition of Metallic Surfaces [in Russian], Naukova Dumka, Kyiv (1976), p. 219.
6. V.P. Botvinko, M.S. Kovalchenko, A.V. Paustovskii, A.I. Yuga, and A.D. Kostenko, “Increasing the wear resistance of surface layers of high-speed steel by electric-spark alloying and laser treatment,” Powder Metall. Met. Ceram., 38, No. 7–8, 362–366 (1999).10.1007/BF02676170 ↗
7. I.O. Podchernyaeva, A.D. Panasyuk, D.V. Yurechko, and A.M. Paramonov, “High-energy electrospark surface strengthening of steels with composite ceramics,” Powder Metall. Met. Ceram., 52, No. 11–12, 656–662 (2014).10.1007/s11106-014-9573-7 ↗
8. V.B. Tarelnyk, A.V. Paustovskii, Y.G. Tkachenko, V.S. Martsinkovskii, E.V. Konoplyanchenko, and K. Antoszewski, “Electric-spark coatings on a steel base and contact surface for optimizing the working characteristics of babbitt friction bearings,” Surf. Eng. Appl. Electrochem., 53, No. 3, 285–294 (2017).10.3103/S1068375517030140 ↗
9. V.B. Tarelnyk, E.V. Konoplyanchenko, P.V. Kosenko, and V.S. Martsinkovskii, “Problems and solutions in renovation of the rotors of screw compressors by combined technologies,” Chem. Petrol. Eng., 53, No. 7–8, 540–546 (2017).10.1007/s10556-017-0378-7 ↗
10. V. Tarelnyk and V. Martsynkovskyy, “Upgrading of pump and compressor rotor shafts using combined technology of electroerosive alloying,” Appl. Mech. Mater., 630, 397–412 (2014).10.4028/www.scientific.net/AMM.630.397 ↗
11. G.V. Samsonov, L.Ya. Markovskii, A.F. Zhygach, and M.G. Valyashko, Boron and Its Compounds and Alloys [in Russian], Izd. Akad. Nauk USSR, Kyiv (1960), p. 590.
12. G.V. Samsonov, T.Ya. Kosolapova, and L.T. Domasevich, Properties, Production Methods, and Applications of Refractory Carbides and Their Alloys [in Russian], Kyiv (1974), p. 208.
13. A.D. Verkhoturov, I.A. Podchernyaeva, L.F. Pryadko, and F.F. Egorov, Electrode Materials for Electrospark Deposition [in Russian], Nauka, Moscow (1988), p. 200.
14. V.P. Konoval, O.P. Umanskii, A.D. Panasyuk, and O.F. Lukyanchuk, “Effect of the chemical composition of electrode materials and deposition parameters on the properties of electrospark-deposited coatings. I. Mass transfer rate and coating composition,” Powder Metall. Met. Ceram., 53, No. 1–2, 31–39 (2014).10.1007/s11106-014-9584-4 ↗
15. V.P. Konoval, O.P. Umanskii, O.D. Kostenko, and I.S. Martsenyuk, “Effect of the chemical composition of electrode materials and deposition conditions on the properties of spark-deposited coatings. II. Coating hardness and wear resistance,” Powder Metall. Met. Ceram., 53, No. 3–4, 210–218 (2014).10.1007/s11106-014-9606-2 ↗
16. A.V. Paustovskii, Yu.G. Tkachenko, R.A. Alfintseva, S.N. Kirilenko, and D.Z. Yurchenko, “Optimization of the composition, structure, and properties of electrode materials and electrospark coatings in strengthening and recovery of metallic surfaces,” Elektrofiz. Obrab. Mater., No. 1, 4–13 (2013).
17. G.A. Bovkun, Yu.G. Tkachenko, and D.Z. Yurchenko, “Tungsten-free electrode materials for electrospark deposition on metallic surfaces,” Elektrofiz. Obrab. Mater., No. 5, 27–29 (1983).
18. C. Luo, X.A. Xiong, and S.J. Dong, “TiB2/Ni coatings on surface of copper alloy electrode prepared by electrospark deposition,” Trans. Nonferrous Met. Soc. China, 21, 317–321 (2011).10.1016/S1003-6326(11)60715-2 ↗
19. A.V. Paustovskii and V.I. Novikova, “Evaluation of tribological characteristics of electric-spark coatings prepared on steel with electrode materials of the system TiN–Ni,” Powder Metall. Met. Ceram., 44, No. 5–6, 240–244 (2005).10.1007/s11106-005-0087-1 ↗
20. O.P. Umanskii, V.P. Konoval, and A.D. Panasyuk, “Electrospark deposition of coatings from titanium–chromium carbide and diboride composites,” Sverkhtverd. Mater., No. 4, 84–91 (2009).
21. S. Frangini, A. Masci, and A. Di Bartolomeo, “Cr7C3-based cermet coating deposited on stainless steel by electrospark process: structural characteristics and corrosion behavior,” Surf. Coat. Technol., No. 149, 279– 286 (2002).
22. A.V. Paustovskii, Yu.G. Tkachenko, V.G. Khristov, R.A. Alfintseva, and D.Z. Yurechko, “Materials for electrospark hardening and recovery of worn metallic surfaces,” Elektron. Obrab. Mater., 52, No. 1, 13–21(2016).
23. M. Storozhenko, O. Umanskyi, V. Krasovskyy, O. Terentjev, and M. Antonov, “Wetting and interfacial behavior in TiB2–NiCrBSiC system,” Alloys Compd., 778, 15–22 (2019).10.1016/j.jallcom.2018.11.102 ↗
24. O. Umanskyi, M. Storozhenko, V. Krasovskyi, and M. Pareyko, “Wettability and interfacial behavior “Febased self-fluxing alloy–refractory compound” systems,” Sverkhtverd. Mater., No. 3–4, 99–105 (2017).
25. A.P. Umanskii, M.S. Storozhenko, A.E. Terentiev, and I.S. Martsenyuk, “Structurization of composites from self-fluxing alloys with titanium diboride additions,” Powder Metall. Met. Ceram., 53, No. 5–6, 359–367 (2014).10.1007/s11106-014-9624-0 ↗
26. A.P. Umanskii, M.S. Storozhenko, I. Hussainova, A.E. Terentiev, A.M. Kovalchenko, and M. Antonov, “Structure, phase composition and wear mechanisms of plasma-sprayed NiCrBSi–20 wt.% TiB2 coating,” Powder Metall. Met. Ceram., 53, No. 11–12, 663–671 (2015).10.1007/s11106-015-9661-3 ↗
27. O. Umanskyi, M. Storozhenko, I. Hussainova, O. Terentyev, A. Kovalchenko, and M. Antonov, “Effect of TiB2 additives on wear behavior of NiCrSiB-based plasma sprayed coatings,” Mater. Sci., 22, 15–19 (2016).
28. O. Umanskyi, I. Hussainova, M. Storozhenko, O. Terentyev, and M. Antonov, “Effect of oxidation on sliding wear behavior of NiCrSiB–TiB2 plasma sprayed coatings,” Key Eng. Mater., 604, 16–19 (2014).10.4028/www.scientific.net/KEM.604.16 ↗
29. O. Umanskyi, M. Storozhenko, M. Antonov, A. Terentiev, O. Koval, and D. Goljandin, “Effect of thermal spraying method on the microstructure and wear behaviour of FeNiCrBSiC–CrB2 coating,” Key Eng. Mater., 604, 16–19 (2019).10.4028/www.scientific.net/KEM.604.16 ↗
30. N. Kazamer, P.C. Valean, D. Pascal, V.A. Serban, R. Muntean, and G. Margineal, “Microstructure and phase composition of NiCrBSi–TiB2 vacuum furnace fused flame-sprayed coatings,” in: 7th Int. Conf. Advanced Mater. Structures—AMS (2018), Vol. 416, pp. 1–7.
31. O.P. Umanskyi, M.S. Storozhenko, V.B. Tarelnik, O.Yu. Koval, Yu.V. Guvin, N.V. Tarelnik, and T.V. Kurinna, “Electrospark deposition of FeNiCrBSiC–MeB2 coatings on steel,” Powder Metall. Met. Ceram., 59, No. 1–2, 57–67 (2020).10.1007/s11106-020-00138-5 ↗
32. E.T. Mamykin and A.I. Yuga, “A set of machines and a method for determining the bearing characteristics of materials under sliding friction conditions,” Powder Metall. Met. Ceram., 12, No. 1, 55–58 (1973).10.1007/BF00803978 ↗
33. ASM Ready Reference: Thermal Properties of Metals, URL:http://www.owlnet.rice.edu/~msci301/ThermalExpansion.pdf (access date May 25, 2020).
34. O.P. Umanskyi, M.S. Storozhenko, M.V. Koshelev, M. Antonov, M.A. Vasylkivska, and I.I. Timofeeva, “Effect of Fe(Ni)CrBSiC–MeB2 material composition on the oxidation behavior at high temperatures,” Powder Metall. Met. Ceram., 57, No. 11–12, 670–678 (2018).