Effect of Carbon Content on Microstructure and Mechanical Properties of Powder Metallurgy Steels
Source abstract
Abstract
In this study, steels, containing different proportions of C, were produced through powder metallurgy. The microstructure and mechanical properties of the produced powder-metallurgy (PM) steels were examined. The sintered density of PM steels was determined, and their microstructures were identified with optical microscopy, SEM, and EDS analyses. The results indicated that there was a significant increase in strength, but a decrease in elongation with an increase in C content. Considering the advantages of PM method, the results achieved in this study came almost close to rolled steel products.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Powder Metallurgy Techniques and Materials · Advanced materials and composites · Metal Alloys Wear and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. J. P. Sharma, S. Chaturvedi, and P. Arora, “Studies on effect of percentage of carbon on the tensile and compressive strength of structural steel,” Int. J. Eng. Sci. Technol., 4, No. 5, 2328–2333 (2012).
2. M. S. Htun, S. T. Kyaw, and K. T. Lwin, “Effect of heat treatment on microstructures and mechanical properties of spring steel,” J. Met. Mater. Miner., 18, No. 2, 191–192 (2008).
3. S. A. Tukur, M. M. Usman, I. Muhammad, et al., “Effect of tempering temperature on mechanical properties of medium carbon steel,” Int. J. Eng. Trends Technol., 9, No. 15, 798–800 (2014).10.14445/22315381/IJETT-V9P350 ↗
4. A. Calik, A. Duzgun, O. Sahin, et al., “Effect of carbon content on the mechanical properties of medium carbon steels,” Verlag der Zeitschrift für Naturforschung, 65, 468–472 (2010).10.1515/zna-2010-0512 ↗
5. A. Güral, S. Tekeli, D. Özyürek, et al., “Effect of repeated quenching heat treatment on microstructure and dry sliding wear behavior of low carbon PM steel,” Mater. Sci. Forum, 534, 673–676 (2007). DOI: 10.4028/www.scientific.net/MSF.534-536.673 .10.4028/www.scientific.net/MSF.534-536.673 ↗
6. S. Tekeli, A. Güral, and D. Özyürek, “Microstructure and dry sliding wear properties of 3Si–2Ni and 3Si–2Mn powder metallurgy steels with different graphite content,” J. Eng. Tribol., 225, No. 8, 814–820 (2011). DOI: 10.1177/1350650111405255 .10.1177/1350650111405255 ↗
7. S. R. Nimbhorkar and B. D. Deshmukh, “Effect of case hardening treatment on the structure and properties of automobile gears,” Int. J. Mod. Eng. Res., 3, No. 2, 637–641 (2013).
8. D. O. Oluyemia, O. I. Oluwoleb, and B. O. Adewuy, “Studies of the properties of heat treated rolled medium carbon steel,” Mater. Res., 14, No. 2, 135–141 (2011). DOI: 10.1590/S1516-14392011005000040 .10.1590/S1516-14392011005000040 ↗
9. P. W. Lee, in: E. Klar (ed.), Powder Metallurgy Applications, Advantages and Limitations, ASM, New York (1983).
10. T. K. Kandavel, R. Chandramouli, and D. Shanmugasundaram, “Experimental study of the plastic deformation and densification behavior of some sintered low alloy P/M steels,” Mater. Des., 30, No. 5, 1768–1776 (2009). DOI: 10.1016/j.matdes.2008.07.027 .10.1016/j.matdes.2008.07.027 ↗
11. W. D. W. Angel, L. T. Jurado, E. C. Martinez, et al., “Effect of carbon on the density, microstructure and hardness of alloys formed by mechanical alloying,” Mater. Des., 60, 605–611 (2014). DOI: 10.1016/j.matdes.2014.04.039 .10.1016/j.matdes.2014.04.039 ↗
12. R. Narayanasamy, V. Anandakrishnan, and K. S. Pandey, “Effect of carbon content on workability of powder metallurgy steels,” Mater. Sci. Eng. A, 494, 337–342 (2008). DOI: 10.1016/j.msea.2008.04.022 .10.1016/j.msea.2008.04.022 ↗
13. M. Abdel-Rahman and M. N. El-Sheikh, “Workability in forging of powder metallurgy compacts,” J. Mater. Process. Technol., 54, 97–102 (1995). DOI: 10.1016/0924-0136(95)01926-X .10.1016/0924-0136(95)01926-X ↗
14. L. E. G. Cambronero, C. Fernandez, J. M. Torralba, et al., “Influence of powders on final properties and microstructure of sintered molybdenum steels,” Powder Metall., 37, 53–56 (1994). DOI: 10.1179/pom.1994.37.1.53 .10.1179/pom.1994.37.1.53 ↗
15. M. Fodor and J. V. Wood, “Effect of carbon on microstructure of mixed powder system cooled at moderate rates after sintering,” Powder Metall., 38, 141–146 (1995). DOI: 10.1179/pom.1995.38.2.14110.1179/pom.1995.38.2.141 ↗
16. M. Youseffi, C. S. Wright, and F. M. Jeyacheya, “Effect of carbon content, sintering temperature, density, and cooling rate upon properties of prealloyed Fe–1.5Mo powder,” Powder Metall., 43, 270–274 (2000). DOI: 10.1179/003258900666041 .10.1179/003258900666041 ↗
17. M. A. Erden, S. Gündüz, M. Türkmen, et al., “Microstructural characterization and mechanical properties of microalloyed powder metallurgy steels,” Mater. Sci. Eng. A, 616, 201–206 (2014). DOI: 10.1016/j.msea.2014.08.026 .10.1016/j.msea.2014.08.026 ↗
18. C. Schade, T. Murphy, A. Lawley, et al., “Microstructure and mechanical properties of microalloyed PM steels,” Int. J. Powder Metall., 48, 51–59 (2012).
19. C. Schade, T. Murphy, A. Lawley, et al., “Microstructure and mechanical properties of PM steels alloyed with silicon and 3-vanadium,” Int. J. Powder Metall., 48, 41–48 (2012).
20. A. Güral and S. Tekeli, “Microstructural characterization of intercritically annealed low alloy PM steels,” Mater. Des., 28, 1224–1230 (2007). DOI: 10.1016/j.matdes.2006.01.007 .10.1016/j.matdes.2006.01.007 ↗
21. W. Jing, W. Yisan, and D. Yichao, “Production of (Ti, V) C reinforced Fe matrix composites,” Mater. Sci. Eng. A, 454, 75–79 (2007). DOI: 10.1016/j.msea.2006.11.024 .10.1016/j.msea.2006.11.024 ↗
22. S. Saritaş, M. Türker, and N. Durlu, Powder Metallurgy and Particulate Materials Processing, Turkish PM Publications (2007), pp. 404–410.
23. S. Gündüz and A. Çapar, “Influence of forging and cooling rate on microstructure and properties of medium carbon microalloy forging steel,” J. Mater. Sci. Lett., 14, No. 2, 561–564 (2006). DOI: 10.1007/s10853-005-4239-y .10.1007/s10853-005-4239-y ↗
24. G. Cipolloni, C. Menapace, I. Cristofolini, et al., “A quantitative characterization of porosity in a Cr–Mo sintered steel using image analysis,” Mater. Charact., 94, 58–68 (2014). DOI : 10.1016/j.matchar.2014.05.005 .10.1016/j.matchar.2014.05.005 ↗
25. A. B. Blank and L. P. Eksperiandova, “Specimen preparation in X-ray fluorescence analysis of materials and natural objects,” X-Ray Spectrom., 27, No. 3, 147–160 (1998). DOI: 10.1002/(SICI)1097-4539(199805/06)27:33.0.CO;2-P .10.1002/(SICI)1097-4539(199805/06)27:33.0.CO;2-P ↗