journal article·2019-03

Investigation of Microstructural Evolution in Ball-Milling of SiC Reinforced Aluminum Matrix Composites

V. Erturun, O. Sahin

Powder Metallurgy and Metal Ceramics· Volume 57· Issue 11-12
Publisher page

Abstract

SiC reinforced Al–Mg–Si powders were ball-milled in a mixer device with different milling times. This process was performed to observe the possible effects of different milling times on the final microstructure and properties of the materials. Mechanically alloyed powder mixtures were sintered to produce a billet in protective gas atmosphere (argon). Then, the billets were polished, and the microstructures of the obtained billets by sintering were investigated using a scanning electron microscope (SEM). Powder mixtures were analyzed by X-ray diffraction (XRD) for the investigation of the phases. The crystal sizes of the mixed powders were calculated using XRD peaks with the Scherrer equation. It was found that SiC particles were uniformly distributed in the composite matrix. It has been observed that as the milling time increases, the size of the matrix grains decreases due to decrease in the crystal size. By increasing the milling time, the work hardening of the composite powder particles, hardness and, consequently, brittleness increase.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (12)

Show source-provided references
1. Y. Chen, T. Chen, S. Zhang, and P. Li, “Effect of ball milling on microstructural evolution during partial remelting of 6061 aluminum alloy prepared by cold-pressing of alloy powders,” Trans. Nonferrous Met. Soc. China, 25, No. 7, 2113–2121 (2015).10.1016/S1003-6326(15)63822-5 ↗
2. K. Abdullahi, and N. Al-Aqeeli, “Mechanical alloying and spark plasma sintering of nano-SiC reinforced Al–12Si–0.3Mg alloy,” Arabian J. Sci. Eng., 39, No. 4, 3161–3168 (2014).10.1007/s13369-013-0780-1 ↗
3. C. Suryanarayana, “Mechanical alloying and milling,” Prog. Mater. Sci., 46, Nos. 1–2, 1–184 (2001).10.1016/S0079-6425(99)00010-9 ↗
4. A. Abdollahi, A. Alizadeh, and H.R. Baharvandi, “Dry sliding tribological behavior and mechanical properties of Al2024–5 wt.% B4C nanocomposite produced by mechanical milling and hot extrusion,” Mater. Design, 55, 471–481 (2014).10.1016/j.matdes.2013.09.024 ↗
5. J. Bhatta, N. Balachandera, S. Shekhera, R. Karthikeyan, D.R. Peshwea, and B.S. Murty, “Synthesis of nanostructured Al–Mg–SiO2 metal matrix composites using high-energy ball milling and spark plasma sintering,” J. Alloys Compd., 536, S35–S40 (2012).10.1016/j.jallcom.2011.12.062 ↗
6. Em. Sharifi and F. Karimzadeh, “Wear behavior of aluminum matrix hybrid nanocomposites fabricated by powder metallurgy,” Wear, 271, No. 7, 1072–1079 (2011).10.1016/j.wear.2011.05.015 ↗
7. M. Oehring, T. Klassen, and R. Bormann, “The formation of metastable Ti–Al solid solutions by mechanical alloying and ball milling,” J. Mater. Res., 8, No. 11, 2819–2829 (1993).10.1557/JMR.1993.2819 ↗
8. H.K. Gusaiwal and S. Pattanaik, Synthesis of Al–Si–Ni nanostrustured materials by mechanical alloying, https://tr.scribd.com/document/328843768/project-hemant-08-05-09-pdf; Accessed 30.03.2018.
9. R. Sankar and P. Singh, “Synthesis of 7075 Al/SiC particulate composite powders by mechanical alloying,” Mater. Lett., 36, Nos. 1–4, 201–205 (1998).10.1016/S0167-577X(98)00026-3 ↗
10. K.M. Lee, and P.H. Shingu, “Solid state reaction between powders and foils by low-energy ball milling,” J. Alloys Compd., 241, Nos. 1–2, 153–159 (1996).10.1016/0925-8388(96)02306-7 ↗
11. M. Alizadeh and M. Aliabadi, “Synthesis behavior of nanocrystalline Al–Al2O3 composite during low time mechanical milling process,” J. Alloys Compd., 509, No. 15, 4978–4986 (2011).10.1016/j.jallcom.2011.01.177 ↗
12. K.D. Woo and D.L. Zhang, “Fabrication of Al–7 wt.% Si–0.4 wt.% Mg/SiC nanocomposite powders and bulk nanocomposites by high energy ball milling and powder metallurgy,” Current Appl. Phys., 4, Nos. 2–4, 175–178 (2004).10.1016/j.cap.2003.11.002 ↗