New Coating Technique for Al–B4C Composite Coatings by Mechanical Milling and Composite Coating
Source abstract
Abstract
Mechanical milling (MM) process as a novel technique for producing Al–B4C composite coatings on the surface of low carbon steel was investigated. The coating thickness, morphology, and cross-section microstructure of the composite coatings were analyzed with scanning electron microscopy (SEM). Also, Vickers microhardness and surface roughness of the coating layer were measured. It was found that a dense Al–B4C composite coating could deposit on the surface, particularly, if longer milling periods. The microstructure of Al–B4C composite coatings revealed that the distribution of B4C particles in the Al matrix was homogenous. Increasing milling time from 6 to 30 h resulted in increase of the microhardness values from 220 to 280 HV for the pre-interface layer (5 μm).
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (27)
Show source-provided references
1. S. Li, B. Sun, H. Imai, et al., “Powder metallurgy titanium metal matrix composites reinforced with carbon nanotubes and graphite,” Composites: Part A, 48, 57–66 (2013).10.1016/j.compositesa.2012.12.005 ↗
2. D. Özyürek, S. Tekeli, A. Güral, et al., “Effect of Al2O3 amount on microstructure and wear properties of Al–Al2O3 metal matrix composites prepared using mechanical alloying method,” Powder Metall. Met. Ceram., 49, 289–294 (2010).10.1007/s11106-010-9235-3 ↗
3. L. F. Guleryuz, S. Ozan, D. Uzunsoy, and R. Ipek, “An investigation of the microstructure and mechanical properties of B4C reinforced PM magnesium matrix composites,” Powder Metall. Met. Ceram., 51, 456–462 (2012).10.1007/s11106-012-9455-9 ↗
4. T. Varol and A. Canakci, “Effect of weight percentage and particle size of B4C reinforcement on physical and mechanical properties of powder metallurgy Al2024–B4C composites,” Met. Mater. Int., 19, 1227–1234 (2013).10.1007/s12540-013-6014-y ↗
5. L. A. Dobrzanski, A. Wlodarczyk, and M. Adamiak, “Structure, properties and corrosion resistance of PM composite materials based on EN AW-2124 aluminum alloy reinforced with the Al2O3 ceramic particles,” J. Mater. Process Technol., 162–163, 27–32 (2005).10.1016/j.jmatprotec.2005.02.006 ↗
6. J. Corrochano, M. Lieblich, and J. Ibanez, “The effect of ball milling on the microstructure of powder metallurgy aluminium matrix composites reinforced with MoSi2 intermetallic particles,” Composites: Part A, 42, 1093–1099 (2011).10.1016/j.compositesa.2011.04.014 ↗
7. M. J. Chao, X. Niu, B. Yuan, et al., “Preparation and characterization of in situ synthesized B4C particulate reinforced nickel composite coatings by laser cladding,” Surf. Coat. Technol., 201, 1102–1108 (2006).10.1016/j.surfcoat.2006.01.032 ↗
8. A. Canakci, F. Erdemir, T. Varol, and S. Ozkaya, “Formation of Fe-Al intermetallic coating on low-carbon steel by a novel mechanical alloying technique,” Powder Technol., 247, 24–29, (2013).10.1016/j.powtec.2013.07.002 ↗
9. L. Takacs and A. R. Torosyan, “Surface mechanical milling of an aluminum plate,” J. Alloys Compd., 434, 686–688 (2007).10.1016/j.jallcom.2006.08.224 ↗
10. Z. Zhan, Y. He, D. Wang, and W. Gao, “Low-temperature processing of Fe–Al intermetallic coatings assisted by ball milling,” Intermetallics, 14, 75–81 (2006).10.1016/j.intermet.2005.04.019 ↗
11. M. Krasnowski, A. Grabias, and T. Kulik, “Phase transformations during mechanical milling of Fe–50% Al and subsequent heating of the milling product,” J. Alloys Compd., 424, 119–127 (2006).10.1016/j.jallcom.2005.12.077 ↗
12. C. Suryanarayana, “Mechanical milling and milling,” Prog. Mater. Sci., 46, 1–184 (2001).10.1016/S0079-6425(99)00010-9 ↗
13. T. Varol and A. Canakci, “Effect of particle size and ratio of B4C reinforcement on properties and morphology of nanocrystalline Al2024-B4C composite powders,” Powder Technol., 246, 462–472, (2013).10.1016/j.powtec.2013.05.048 ↗
14. M. Tahari, M. Shamanian, and M. Salehi, “Microstructural and morphological evaluation of MCrAlY/YSZ composite produced by mechanical milling method,” J. Alloys Compd., 525, 44–52 (2012).10.1016/j.jallcom.2012.01.161 ↗
15. N. Zhao, P. Nash, and X. Yang, “The effect of mechanical milling on SiC distribution and the properties of 6061 aluminum composite,” J. Mater. Process Technol., 170, 586–592 (2005).10.1016/j.jmatprotec.2005.06.037 ↗
16. I. Farahbakhsh, A. Zakeri, P. Manikandan, and K. Hokamoto, “Evaluation of Nanostructured coating layers formed on Ni balls during mechanical milling of Cu powder,” Appl. Surf. Sci., 257, 2830-2837 (2011).10.1016/j.apsusc.2010.10.071 ↗
17. K. Lu and J. Lu, “Nanostructured surface layer on metallic materials induced by surface mechanical attrition treatment,” Mater. Sci. Eng. A, 375-377, 38–45 (2004).10.1016/j.msea.2003.10.261 ↗
18. A. Revesz and L. Takacs, “Coating metals by surface mechanical attrition treatment,” J. Alloys Compd., 441, 111–114 (2007).10.1016/j.jallcom.2006.09.081 ↗
19. S. Romankov, W. Sha, S. D. Kaloshkin, and K. Kaevitser, “Fabrication of Ti-Al coatings by mechanical milling method,” Surf. Coat. Technol., 201, 3235–3245 (2006)10.1016/j.surfcoat.2006.06.044 ↗
20. S. Romankov, S. D. Kaloshkin, Y. Hayasaka, et al., “Effect of process parameters on the formation of Ti-Al coatings fabricated by mechanical milling,” J. Alloys Compd., 484, 665–673 (2009).10.1016/j.jallcom.2009.05.016 ↗
21. V. Zadorozhnyya, S. Kaloshkin, E. Kaevitserv, and S. Romankov, “A vanadium-based conversion coating as chromate replacement for electrogalvanized steel substrates,” J. Alloys Compd., 509, 507–509 (2011).10.1016/j.jallcom.2011.01.164 ↗
22. S. Romankov, S. V. Komarov, E. Vdovichenko, et al., “Fabrication of TiN coatings using mechanical milling techniques,” Int. J. Refract. Met. Hard Mater., 27, 492–497 (2009).10.1016/j.ijrmhm.2008.10.005 ↗
23. D. Gu and Y. Shen, “Microstructures and properties of high Cr content coatings on inner surfaces of carbon steel tubular components prepared by a novel mechanical milling method,” Appl. Surf. Sci., 256, 223–230 (2009).10.1016/j.apsusc.2009.08.004 ↗
24. B. Li, R. Ding, Y. Shen, et al., “Preparation of Ti–Cr and Ti–Cu flame-retardant coatings on Ti–6Al–4V using a high-energy mechanical milling method,” A preliminary research. Mater. Des., 35, 25–36 (2012).
25. H. S. Lee, H. Shin, and K. Ko, “Mechanical matching and microstructural evolution at the coating/substrate interfaces of cold-sprayed Ni, Al coatings,” J. Alloys Compd., 478, 636–641 (2009).10.1016/j.jallcom.2008.11.150 ↗
26. A. Canakci and T. Varol, “Structural evolution and characterization of nanostructured Al–Al2O3 composite fabricated by mechanical alloying method,” Rom. J. Mater., 43(3), 312–319 (2013).
27. R. Pouriamanesh, J. V. Khaki, and Q. Mohammadi, “Coating of Al substrate by metallic Ni through mechanical milling,” J. Alloys Compd., 488, 430–436 (2009).10.1016/j.jallcom.2009.08.150 ↗