Effect of Composition on Structural and Magnetic Properties of Nanocrystalline Ferrite Li0.5Sm x Fe2.5–x O4
Source abstract
Abstract
The effect of Sm content Li0.5Sm x Fe2.5–x O4 (x = 0, 0.05, 0.1, and 0.2) and sintering temperature on the phase evolution, microstructure, and bulk magnetic properties of lithium ferrite prepared by mechanical alloying is investigated. XRD results of pure samples confirmed that the single ferrite phase is formed after sintering at 800°C; however, increasing of samarium content led to the formation of secondary phase (SmFeO3) and enhanced intensity. The bulk magnetic properties decreased with increase Sm content and increased with sintering temperatures. Single-phase ferrites Li0.5Sm x Fe2.5–x O4 were produced by sintering of sample at 800°C, which is lower than the temperature associated with the conventional ceramic procedure.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnetic Properties and Synthesis of Ferrites · Iron oxide chemistry and applications · Electromagnetic wave absorption materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (45)
Show source-provided references
1. P. Baba, G. C. Argentina, W. Dionne, and Temme, "Fabrication and properties of microwave lithium ferrites," IEEE Transac. Magn., 8, No. 1, 83–94 (1972).10.1109/TMAG.1972.1067269 ↗
2. A. A. Sattar, H. M. El-Sayed, and W. R. Agami, "Physical and Magnetic Properties of Calcium-Substituted Li-Zn Ferrite," J. Mater. Engin. Perform., 16, No. 5, 573–577 (2007).10.1007/s11665-007-9080-9 ↗
3. Y. Yafet and C. Kittel, "Antiferromagnetic arrangements in ferrites," Phys. Rev., 87, No. 2, 290–294 (1952).10.1103/PhysRev.87.290 ↗
4. N. Rezlescu et al., "Lithium ferrite for gas sensing applications," Sens. Actuat. B: Chem., 133, No. 2, 420–425 (2008).10.1016/j.snb.2008.02.047 ↗
5. B. Ashok, T. G. S. Gadkaria, and N. Pramod Vasambekar, "Effect of Sm3+ ion addition on gas sensing properties of Mg1−x Cd x Fe2O4 system," Sens. Actuat. B, 178, 34–39 (2013).10.1016/j.snb.2012.12.023 ↗
6. R. G. West and A. C. Blankenship, "Magnetic properties of dense lithium ferrites," J. Amer, Cer, Soc,, 50, No. 7, 343–349 (1967).10.1111/j.1151-2916.1967.tb15129.x ↗
7. Samiha T. Bishay, Rasha M. Khafagy, N. M. Saleh, and M.A. Ahmed, "Promising wastewater treatment using rare earth-doped nanoferrites," J. Magn. Magn. Mater., (2014).
8. G. Dascalu, T. Popescu, M. Feder, and O. F. Caltun, "Structural, electric and magnetic properties of CoFe1.8RE0.2O4 (RE=Dy, Gd, La) bulk materials," J. Magn. Magn. Mater., 333, 69–74 (2013).10.1016/j.jmmm.2012.12.048 ↗
9. R. Islam, M. A. Hakim, M. O. Rahman, et al., "Study of the structural, magnetic, and electrical properties of Gd-substituted Mn–Zn mixed ferrites," J. Alloys Compd., 559, 174–180 (2013).10.1016/j.jallcom.2012.12.080 ↗
10. S. Wells and C. V. Ramana, "Effect of hafnium-incorporation on the microstructure and dielectric properties of cobalt ferrite ceramics," Ceram. Inter., 39, No. 8, 9549–9556 (2013).10.1016/j.ceramint.2013.05.073 ↗
11. S. Amiri and H. Shokrollahi, "Magnetic and structural properties of RE doped Co-ferrite (RENd, Eu, Gd) nano-particles synthesized by co-precipitation," J. Magn. Magn. Mater., 345, 18–23 (2013).10.1016/j.jmmm.2013.05.030 ↗
12. M. Yehia, S. M. Ismal, and A. Hashhash, "Structural and magnetic studies of rare-earth substituted nickel ferrites," J. Superconduct. Nov. Magn., 27, No, 3, 771–774 (2014).10.1007/s10948-013-2340-z ↗
13. A. M. Samy, "The influence of the preparation conditions on the initial permeability of Cu0.5Zn0.5Fe2−x R x O4," J. Mater. Engin. Perform., 20, No. 7, 1315–1318 (2011).10.1007/s11665-010-9760-8 ↗
14. Ashok Gadkari, Tukaran Shinde, and Pramod Vasambekar, "Influence of rare-earth ions on structural and magnetic properties of CdFe2O4 ferrites," Rar. Met., 29, No. 2, 168–173 (2010).10.1007/s12598-010-0029-z ↗
15. S. Amiri and H. Shokrollahi, "Magnetic and structural properties of RE doped Co-ferrite (RENd, Eu, Gd) nano-particles synthesized by co-precipitation," J, Magn, Magn, Mater, 345, 18–23 (2013).10.1016/j.jmmm.2013.05.030 ↗
16. A. M. Samy, "Improvement of the magnetic and electrical properties of Cu–Zn ferrites," J. Mater. Engin. Perform., 12, No. 5, 569–572 (2003).10.1361/105994903100277076 ↗
17. Muthafar F. Al-Hilli, Sean Li, and Kassim S. Kassim, "Structural analysis, magnetic and electrical properties of samarium substituted lithium–nickel mixed ferrites," J. Magn. Magn. Mater., 324, No. 5, 873–879 (2012).10.1016/j.jmmm.2011.10.005 ↗
18. I. Chicinas, "Soft magnetic nanocrystalline powders produced by mechanical alloying routes," J. Ortoelectr. Adv. Mater., 8, No. 2, 439–448 (2006).
19. Diandra L. Leslie-Pelecky and Reuben D. Rieke, "Magnetic properties of nanostructured materials," Chem. Mater., 8, No. 8, 1770–1783 (1996).10.1021/cm960077f ↗
20. C. Suryanarayana and Nasser Al-Aqelli, "Mechanically alloyed nanocomposites," Prog. Mater. Sci., 58, No. 4, 383–502 (2013).
21. C. Suryanarayana and C. C. Koch, "Nanocrystalline materials – Current research and future directions," Hyper. Inter., 130, No. 1–4, 5–44 (2000)10.1023/A:1011026900989 ↗
22. C. Suryanarayana, "Nanocrystalline materials," Inter. Mater. Rev., 40, No. 2, 41–64 (1995).10.1179/imr.1995.40.2.41 ↗
23. M. Kavanloui, B. Hashemi, and E. Nourafkan, "Optimization of Li-Zn ferrite synthesis parameters using the experimental design method," J. Chem. Engin. Mater. Sci., 2, No. 4, 53–60 (2011).
24. M. Asif Iqbal et al., "High frequency dielectric properties of Eu+3-substituted Li–Mg ferrites synthesized by sol–gel auto-combustion method," J. Alloys Compd., 586, No. 0, 404–410 (2014).10.1016/j.jallcom.2013.10.066 ↗
25. Ihsan Ali, M. U. Islam, M. S. Awan, and Mukhtar Ahmad, "Electric and Dielectric Properties of Cr–Ga Substituted BaM Hexaferrites for High-Frequency Applications," J. Mater. Engin. Perform., 22, No. 9, 2673–2680 (2013).10.1007/s11665-013-0562-7 ↗
26. M. Gupta and B. S. Randhawa, "Microstructural, magnetic and electric properties of mixed Cs–Zn ferrites prepared by solution combustion method," Sol. St. Sci., 14, No. 7, 849–856 (2012).10.1016/j.solidstatesciences.2012.04.010 ↗
27. W. R. Agami, M. A. Ashmawy, and A. A. Sattar, "Structural, IR, and magnetic studies of annealed Li-Ferrite nanoparticles," J. Mater. Engin. Perform., 23, No. 2, 604–610 (2014).10.1007/s11665-013-0754-1 ↗
28. M. Kavanloui and B. Hashemi, "Effect of B2O3 on the densification and magnetic properties of Li–Zn ferrite," Mater. Des., 32, No. 8–9, 4257–4261 (2011).10.1016/j.matdes.2011.04.019 ↗
29. M. M. Eltabey and W. R. Agami, "Effect of single and double sintering on microstructure and magnetic properties of Gd-substituted Ni-Cd ferrites," J. Mater. Engin. Perform., 22, No. 11, 3461–3465 (2013).10.1007/s11665-013-0609-9 ↗
30. A. C. H. Barreto et al., "Grain size control of the magnetic nanoparticles by solid state route modification," J. Mater. Engin. Perform., 22, No. 7, 2073–2079 (2013).10.1007/s11665-013-0480-8 ↗
31. Irshad Ali et al., "Structural and magnetic properties of holmium substituted cobalt ferrites synthesized by chemical co-precipitation method," J. Magn. Magn. Mater., 324, No. 22, 3773–3777 (2012).10.1016/j.jmmm.2012.06.008 ↗
32. C. Suryanarayana, E. Ivanov, and V. V. Boldyrev, "The science and technology of mechanical alloying," Mater. Sci. Engin.: A, 304–306, No.0, 151–158 (2001).10.1016/S0921-5093(00)01465-9 ↗
33. D. L. Zhang, "Processing of advanced materials using high-energy mechanical milling," Progr. Mater. Sci., 49, Nos. 3–4, 537–560 (2004).10.1016/S0079-6425(03)00034-3 ↗
34. H. M. Widatallah, X. L. Ren, and I. A. Al-Omari, "The influence of TiO2 polymorph, mechanical milling and subsequent sintering on the formation of Ti-substituted spinel-related Li0.5Fe2.5O4," J. Mater. Sci., 41, No.19, 6333–6338 (2006).10.1007/s10853-006-0721-4 ↗
35. S. H. Gee, Y. K. Hong, M. H. Park, et al., "Synthesis of nanosized (Li0.5x Fe0.5x Zn1–x )Fe2O4 particles and magnetic properties," J. Appl. Phys., 91, No. 10, 7586–7588 (2002).10.1063/1.1453931 ↗
36. H. Lipson, The Study of Metals and Alloys by X-ray Powder Diffraction Methods, in: Pamphlet 16, (International Union of Crystallography: University College Cardiff Press, Cardiff, Wales), Cardiff, UK (1984).
37. B. D. Cullity and S. R. Stock, Elements of X-ray Diffraction, Vol. 3. 2001: Prentice hall Upper Saddle River, New Jersey (2001), p. 664.
38. A. Goldman, Modern Ferrite Technology, Vol. 2, Springer (2009), p. 438.
39. E. P. Wohlfarth (ed.), Handbook of Magnetic Materials: A Handbook on the Properties of Magnetically Ordered Substances, Vol. 2, North Holland, (1986), p.604.
40. S. S. R. Inbanathan, V. Vaithyanathan, J. Arout Chelvane, et al., "Mössbauer studies and enhanced electrical properties of R (R=Sm, Gd and Dy) doped Ni ferrite," J. Magn. Magn. Mater., 353, p. 41–46 (2014).10.1016/j.jmmm.2013.10.019 ↗
41. L. Néel, "Magnetism and the local molecular field," Science, 174, No. 4013, 985–992 (1971).10.1126/science.174.4013.985 ↗
42. G. K. Williamson and W. H. Hall, "X-ray line broadening from filed aluminium and wolfram," Acta Metallurg., 1, No. 1, 22–31 (1953).10.1016/0001-6160(53)90006-6 ↗
43. E. Rezlescu et al., "The influence of R2O3 (R = Yb, Er, Dy, Tb, Gd, Sm and Ce) on the electric and mechanical properties of a Nickel–Zinc ferrite," Phys. Stat. Sol. (A), 162, No. 2, 673–678 (1997).10.1002/1521-396X(199708)162:2<673::AID-PSSA673>3.0.CO;2-A ↗
44. M. Drofenik, A. Znidarsic, and D. Makovec, "Influence of the addition of Bi2O3 on the grain growth and magnetic permeability of MnZn ferrites," J. Amer. Cer. Soc., 81, No.11, 2841–2848 (2005).10.1111/j.1151-2916.1998.tb02704.x ↗
45. M. Mahmoudi and M. Kavanlouei, "The effect of nano-SiO2 on magnetic and dielectric properties of Li–Zn ferrite," Inter. J. Mater. Res., 105, No. 11, 1097–1102 (2014).10.3139/146.111122 ↗