Structure and Wear Resistance of Plasma-Sprayed NiCrBSiC–TiCrC Composite Powder Coatings
Source abstract
Abstract
The NTC20 and NTC40 composite powders were produced by conglomeration from the NiCrBSiC self-fluxing alloy with additions of 20 and 40 wt.% TiCrC, respectively, using an organic binder. Since the organic binder burnt out in the plasma spray process, components of the composite powders segregated and a certain amount (up to 15–20 vol.%) of the TiCrC particles was lost. The plasma-sprayed NTC20 and NTC40 coatings showed a heterophase lamellar structure, consisting of a nickel-base matrix in which fine chromium boride and carboboride grains (1–2 μm) and TiCrC particles (5–8 μm) were evenly distributed. Electron microprobe analysis revealed a higher content of oxides in the NTC20 and NTC40 coatings compared to the NiCrBSiC coating, which was associated with the oxidation of TiCrC particles in the plasma spray process. The introduction of TiCrC additions into the NiCrBSiC self-fluxing alloy increased porosity of the plasma-sprayed NTC20 and NTC40 coatings (up to 8%) versus the NiCrBSiC coating (5%). Wear tests of the plasma-sprayed NTC20 and NTC40 coatings were performed in dry sliding friction conditions using 65G steel as a counterface. For comparison, a plasma-sprayed coating consisting of the serial NiCrBSiC self-fluxing alloy was tested. Additions of 20 and 40 wt.% TiCrC particles to the NiCrBSiC self-fluxing alloy increased the wear resistance of the plasma-sprayed coatings by 2 to 2.3 times. As the sliding speed increased from 4 to 12 m/sec, the NiCrBSiC coating underwent catastrophic wear (I ≈ 60 μm/km), while the wear rate of the NTC20 and NTC40 coatings remained constant (I ≈ 12–22 μm/km).
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced materials and composites · High-Temperature Coating Behaviors · Metal and Thin Film Mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. K. Holmberg and A. Matthews, Coatings Tribology: Properties, Mechanisms, Techniques and Application in Surface Engineering, 2nd ed., Elsevier (2009), p. 560.
2. V.F. Labunets, A.P. Kudrin, V.V. Zhiginas, O.S. Suprunovich, V.A. Tit, and A.V Melnik, “Analysis of causes behind loss of operability by airplane friction components and methods for their recovery,” Probl. Tertia Znosz., Issue 45, 86–96 (2006).
3. A.P. Kudrin and V.V. Zhiginas, “Fracture of airplane friction components in operation,” Probl. Tertia Znosz., Issue 45, 63–71 (2006).
4. V.I. Tsypak, “Analysis of service damage of tooth joints of drive shafts/springs and recommendations on increase of their life,” Visn. Dvygunobud., No. 4, 61–65 (2004).
5. L. Pavlowski, The Science and Engineering of Thermal Spray Coatings, John Willey & Sons, Chichester (2008), p. 626.10.1002/9780470754085 ↗
6. Yu.A. Kharlamov and L.G. Polonskii, “Thermal spray coatings. Current condition and development prospects,” Visn. Skhidnoukr. Nats. Univ. Dalya, No. 2, 5–9 (2016).
7. Global thermal spray market—growth, trends, and forecasts (2020–2025), URL: https://www.mordorintelligence.com/i (access date: April 12, 2020).
8. Thermal spray coating technology: white paper by the ASM International Thermal Spray Association, TSS Thermal Spray Society; URL: https://www.asminternational.org/documents/17679604/17683439/White+paper.pdf/fba0eade-d6db-4921-b42f-668965d7c70a (access date: April 12, 2020).
9. A. Vardelle, C. Moreau, J. Akedo, et al., “The 2016 thermal spray roadmap,” J. Therm. Spray Technol., 25, Issue 8, 1376–1440 (2016).10.1007/s11666-016-0473-x ↗
10. Yu.S. Borisov, Yu.A. Kharlamov, S.A. Sidorenko, and E.N. Arbatovska, Thermal Spray Coatings of Powder Materials: Handbook [in Russian], Tekhnika, Kyiv (1987), p. 544.
11. A.J. Horlock, D.G. McCartney, P.H. Shipway, and J.V. Wood, “Thermally sprayed Ni(Cr)–TiB2 coatings using powder produced by self-propagating high temperature synthesis: microstructure and abrasive wear behavior,” Mater. Sci. Eng., 336, No. 5(4), 88–98 (2002).
12. M.A. Jones, A.J. Horlock, P.H. Shipway, and D.G. McCartney, “Comparison of the abrasive wear behavior of HVOF sprayed titanium carbide- and titanium boride-based cermet coatings,” Wear, 251, 1009–1016 (2001).10.1016/S0043-1648(01)00702-5 ↗
13. Hong-Bin Zhu, Hui Li, Hai-Xin Yang, and Zhuo-Xin Li, “Microstructure and sliding wear performance of plasma-sprayed TiB2–Ni coating deposited from agglomerated and sintered powder,” J. Therm. Spray Technol., 22, 1310–1319 (2001).10.1007/s11666-013-0015-8 ↗
14. M. Jones, A.J. Horlock, P.H. Shipway, D.G. McCartney, and J.V. Wood, “Microstructure and abrasive wear behavior of FeCr–TiC coatings deposited by HVOF spraying of SHS powders,” Wear, 249, 246–253 (2001).10.1016/S0043-1648(01)00560-9 ↗
15. M.S. Storozhenko, O.P. Umanskii, A.E. Terentiev, and I.M. Zakiev, “Effect of the structure of TiB2–(Fe–Mo) plasma coatings on mechanical and tribotechnical properties,” Powder Metall. Met. Ceram., 56, No. 1–2, 60–69 (2017).10.1007/s11106-017-9872-x ↗
16. G. Bolelli, A. Colella, L. Lusvarghi, S. Morelli, and P. Puddu, “TiC–NiCr thermal spray coatings as an alternative to WC–CoCr and Cr3C2–NiCr,” Wear, 450–451, 1–23 (2020).10.1016/j.wear.2020.203273 ↗
17. Sulzer Metco: URL: http://www.sulzer.com (access date: October 30, 2019).
18. Castolin Eutectic: URL: http://www.castolin.com (access date: October 30, 2019).
19. Höganäs: URL:http://www.// hoganas.com (access date: October 30, 2019).
20. WallCollmonoy: URL:http://www.wallcolmonoy.com (access date: April 14, 2020).
21. Praxair: URL:http://www.praxairsurfacetechnologies.com (access date: April 14, 2020).
22. F. Otsubo, H. Era, and K. Kishitake, “Structure and phases in nickel-base self-fluxing alloy coating containing high chromium and boron,” J. Therm. Spray Technol., 9, 107–113 (2000).10.1361/105996300770350131 ↗
23. P.A Vityaz, A.F. Ilyushchenko, and A.I. Shevtsov, Fundamentals of Depositing Wear-Resistant, Corrosion- Resistant, and Heat-Barrier Coatings [in Russian], Belorusskaya Nauka, Minsk (2006), p. 363.
24. G. Bolelli, B. Bonferonni, J. Laurilla, L. Lusvarghi, A. Milanti, K. Niema, and P. Vuoristo, “Micromechanical properties and sliding wear behavior of HVOF-sprayed Fe-based alloy coatings,” Wear, 276–277, 29–47 (2012).10.1016/j.wear.2011.12.001 ↗
25. S. Houdkova, F. Zahalka, M. Kasparova, and M. Berger, “Comparative study of thermally sprayed coatings under different types of wear conditions for hard chromium replacement,” Tribol. Lett., 43, 139–154 (2011).10.1007/s11249-011-9791-9 ↗
26. C. Katsich and E. Badisch, “Effect of carbide degradation in a Ni-based hardfacing under abrasive and combined impact/abrasive conditions,” Surf. Coat. Technol., 206(6), 1062–1068 (2011).10.1016/j.surfcoat.2011.07.064 ↗
27. A. Martı́n, J. Rodrı́guez, J. E. Fernández, and R. Vijande, “Sliding wear behavior of plasma sprayed WC– NiCrBSi coatings at different temperatures,” Wear, 251, 1017–1022 (2001).10.1016/S0043-1648(01)00703-7 ↗
28. P. Niranatlumpong and H. Koiprasert, “Phase transformation of NiCrBSi–WC and NiBSi–WC arc-sprayed coatings,” Surf. Coat. Technol., 206, 440–445 (2011).10.1016/j.surfcoat.2011.07.057 ↗
29. N. Serres, F. Hlawka, S. Costil, and C. Langlade, “Microstructures and mechanical properties of metallic NiCrBSi and composite NiCrBSi–WC layers manufactured via hybrid plasma/laser process,” Appl. Surf. Sci., 257, 5132–5137 (2011).10.1016/j.apsusc.2010.11.062 ↗
30. Q. Wang, Z.H. Chen, Z.X. Ding, and D. Chen, “Abrasive wear behavior of WC reinforced Ni-based composite coating sprayed and fused by oxyacetylene flame,” Surf. Rev. Lett., 16(3), 475–485 (2009).10.1142/S0218625X09012883 ↗
31. R. Rachidi, B. Kihel, F. Delaunois, V. Vitry, and D. Deschuyteneer, “Wear performance of thermally sprayed NiCrBSi and NiCrBSi–WC coatings under two different wear modes,” J. Mater. Environ. Sci., 8, 4550–4559 (2017).
32. L.M. Berger, S. Saaro, T. Naumann, M. Kasparova, and F. Zahalka, “Microstructure and properties of HVOF-sprayed WC–(W, Cr)2C–Ni coatings,” J. Therm. Spray Technol., 17(3), 395–403 (2008).10.1007/s11666-008-9189-x ↗
33. S.N. Basu and V.K. Sarin, “Oxidation behavior of WC–Co,” Mater. Sci. Eng., 209, 206–212 (1996).10.1016/0921-5093(95)10145-4 ↗
34. G. V. Samsonov and I. M. Vinnitski, Refractory Compounds [in Russian], Metallurgiya, Moscow (1976).
35. Q. Li, T.C. Lei, and W.Z. Chen, “Microstructural characterization of laser-clad TiC-reinforced Ni–Cr–B–Si–C composite coatings on steel,” Surf. Coat. Technol., 14, 278–284 (1999).10.1016/S0257-8972(99)00055-9 ↗
36. L.C. Betancourt-Dougherty and R.W. Smith, “Effects of load and sliding speed on the wear behavior of plasma sprayed TiC–NiCrBSi coatings,” Wear, 217, 147–154 (1998).10.1016/S0043-1648(97)00212-3 ↗
37. Bin Cai, Ye-fa Tan, Long He, Hua Tan, and Li Gao, “Tribological properties of TiC particles reinforced Ni-based alloy composite coatings,” Trans. Nonferrous Met. Soc. China, 23, 1681–1688 (2013).10.1016/S1003-6326(13)62648-5 ↗
38. A. Zikin, E. Badisch, I. Hussainova, C. Tomastik, and H. Danninger, “Characterization of TiC–NiMo reinforced Ni-based hardfacing,” Surf. Coat. Technol., 236, 36–44 (2013).10.1016/j.surfcoat.2013.02.027 ↗
39. N. Kazamer, P.C. Valean, D. Pascal, V.A. Serban, R. Muntean, and G. Margineal, “Microstructure and phase composition of NiCrBSi–TiB2 vacuum furnace fused flame-sprayed coatings,” in: 7th Int. Conf. Advanced Materials and Structures, AMS-2018, Vol. 416, pp. 1–7.10.1088/1757-899X/416/1/012001 ↗
40. N. Kazamer, S. Kossman, I. Baranyi, D. Chicot, V.A. Serban, Z. Rajnai, and M. Voda, “Influence of TiB2 addition on the mechanical and tribological properties of NiCrBSi deposited by flame spraying,” Mater. Tech., 106(2), 1–7 (2018).10.1051/mattech/2018026 ↗
41. O.P. Umanskii, I. Hussainova, M.S. Storozhenko, A.E. Terentiev, A. Maksimov, and A.M. Kovalchenko, “Structure, phase composition, and wear mechanisms of plasma-sprayed NiCrSiB–20 wt.% TiB2 coating,” Powder Metall. Met. Ceram., 53, No. 11–12, 663–671 (2015).10.1007/s11106-015-9661-3 ↗
42. O. Umanskyi, M. Storozhenko, I. Hussainova, O. Terentyev, A. Kovalchenko, and M. Antonov, “Effect of TiB2 additives on wear behavior of NiCrSiB-based plasma sprayed coatings,” Mater. Sci., 22, 15–19 (2016).
43. O. Umanskyi, I. Hussainova, M. Storozhenko, O. Terentyev, and M. Antonov, “Effect of oxidation on sliding wear behavior of NiCrSiB–TiB2 plasma sprayed coatings,” Key Eng. Mater., 604, 16–19 (2014).10.4028/www.scientific.net/KEM.604.16 ↗
44. O.P. Umanskyi, M.S. Storozhenko, V.B. Tarelnik, O.Yu. Koval, Yu.V. Gubin, N.V. Tarelnik, and T.V. Kurinna, “Electrospark deposition of FeNiCrBSiC–MeB2 coatings on steel,” Powder Metall. Met. Ceram., 59, No. 1–2, 57–67 (2020).10.1007/s11106-020-00138-5 ↗
45. M.S. Storozhenko, O.P. Umanskyi, V.B. Tarelnik, O.Yu. Koval, Yu.V. Gubin, M.O. Mikulina, I.S. Martsenyuk, O.D. Kostenko, and T.V. Kurinna, “Structure and wear resistance of Fe(Ni)CrBSiC– MeB2 electrospark coatings,” Powder Metall. Met. Ceram., 59, No. 5–6, 330–341 (2020).10.1007/s11106-020-00166-1 ↗
46. M. Storozhenko, O. Umanskyi, V. Krasovskyy, O. Terentjev, and M. Antonov, “Wetting and interfacial behavior in TiB2–NiCrBSiC system,” Alloys Compd., 778, 15–22 (2019).10.1016/j.jallcom.2018.11.102 ↗
47. O. Umanskyi, M. Storozhenko, V. Krasovskyi, and M. Pareyko, “Wettability and interfacial behavior ‘Febased self-fluxing alloy—refractory compound’ systems,” Nadtverd. Mater., No. 2, 99–105 (2017).
48. O. P. Umanskyi, M. S. Storozhenko, A. E. Terentiev, and I. S. Martsenyuk, “Structurization of composites from self-fluxing alloys with titanium diboride additions,” Powder Metall. Met. Ceram., 53, No. 5–6, 359– 367 (2014).10.1007/s11106-014-9624-0 ↗
49. O.P. Umanskyi, M.S. Storozhenko, M.V. Koshelev, M. Antonov, M.A. Vasylkivska, and I.I. Tymofeeva, “Effect of Fe(Ni)CrBSiC–MeB2 material composition on the oxidation behavior at high temperatures,” Powder Metall. Met. Ceram., 57, No. 11–12, 670–678 (2019).10.1007/s11106-019-00030-x ↗
50. O.P. Umanskyi, V.P. Konoval, A.D. Panasyuk, I.A. Podchernyaeva, V.V. Malyshkin, and V.A. Kralya, “Plasma coatings of (TiCrC)–Fe–Cr composite powder alloys: Structure and properties,” Powder Metall. Met. Ceram., 146, No. 3–4, 133–138 (2007).10.1007/s11106-007-0022-8 ↗
51. O.P. Umanskyi, V.A. Lavrenko, S.S. Chuprov, and V.P. Konoval, “High-temperature oxidation of composite based on double titanium–chromium carbide,” Powder Metall. Met. Ceram., 48, No. 9–10, 607–609 (2009).10.1007/s11106-010-9174-z ↗
52. E.T. Mamykin and A.I. Yuga, “A set of machines and a method for determining the bearing characteristics of materials under sliding friction condition,” Powder Metall. Met. Ceram., 12, No. 1, 55–58 (1973).10.1007/BF00803978 ↗