journal article·2021-05

Review on Powder Metallurgy: a Novel Technique for Recycling and Foaming of Aluminium-Based Materials

Naveen Kumar, Ajaya Bharti

Powder Metallurgy and Metal Ceramics· Volume 60· Issue 1-2
Publisher page

Abstract

The demand for aluminum is very high worldwide because of its high strength, low density, and high electrical and thermal conductivity. Aluminum and its alloys are widely used in automotive, aerospace, packaging, kitchen utensils, construction, electrical cabling, etc. To satisfy the high demand, high production of aluminum and its alloys is essential. However, the sources of primary aluminum (aluminum extracted from ores) are limited. Hence, the efficient recycling of aluminum is vital. Conventional casting is often used to recycle aluminum and its alloys, although the efficiency of such a method is very low. The researchers are therefore working to develop highly efficient aluminum recycling techniques. Powder metallurgy is one of the novel techniques for recycling aluminum due to its high use of materials, its low energy consumption, and its quasi-final production of forms. The powder metallurgy technique is also beneficial in the manufacture of aluminum-based metal foams. There are various ways to prepare aluminum-based metal foams using the powder metallurgy technique. Aluminum-based metal foams are utilized in crashworthiness applications because of their remarkable properties, like low density and high energy absorption capacity. In this work, a study on various methods of recycling and foaming of aluminum-based materials by powder metallurgy is performed. The parameters of the powder metallurgy process, such as the compaction pressure, the weight or density of the reinforcements, and the type of reinforcement, strongly influence the recycling and foaming of aluminum. In this work, the effect of compaction pressure, weight or density fraction of reinforcements, and type of reinforcing agent on the recycling and foaming of aluminum and its alloys was investigated.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Bauxite Residue and Utilization · Nanoporous metals and alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. V. Saraswat and A. Ghosh, Need for an Aluminium Policy in India, NITI AAYOG, Delhi (2017).
2. N.V. Nayak, “Composite materials in aerospace applications,” Int. J. Sci. Research Publ., 4, No. 9, 1–10 (2014).
3. M. Asif, K. Chandra, and P.S. Misra, “Development of aluminium based hybrid metal matrix composites for heavy duty applications,” J. Miner. Mater. Charact. Eng., 10, No. 14, 133–134 (2011).
4. A.K. Bodukuri, K. Eswaraiah, K. Rajendara, and V. Sampath, “Fabrication of Al–SiC–B4C metal matrixcomposite by powder metallurgy techniqueand evaluating mechanical properties,” Perspec. Sci., 8, 428–431 (2016).10.1016/j.pisc.2016.04.096 ↗
5. N.S. Kumar, R. Suresh, and G.S. Shankar, “High temperature wear behavior of Al2219/n-B4C/MoS2 hybrid metal matrix composites,” Composites Communic., 19, No. 1, 61–73 (2020).10.1016/j.coco.2020.02.011 ↗
6. Y. Abdullah, M.R. Yusof, A. Muhammad, N. Kamarudin, W.S. Paulus, R. Shamsudin, N.H. Shudin, and N.M. Zali, “Al/B4C composites with 5 and 10 wt.% reinforcement content prepared by powder metallurgy,” J. Nuclear Related Technol., 9, No. 1, 42–47 (2012).
7. H. Abdoli, H. Farnoush, E. Salahi, and K. Pourazrang, “Study of the densification of a nanostructured composite powder. Part 1: Effect of compaction pressure and reinforcement addition,” Mater. Sci. Eng. A., 486, 580–584 (2008).10.1016/j.msea.2007.09.034 ↗
8. S.S. Anand and B. Mohan, “Effect of particle size, compaction pressure on density and mechanical properties of elemental 6061 Al alloy through powder metallurgical process,” Int. J. Mater. Eng. Innovat., 3, 259–268 (2012).10.1504/IJMATEI.2012.049265 ↗
9. M. Samuel, “A new technique for recycling aluminium scrap,” J. Mater. Proc. Technol., 135, 117–124 (2003).10.1016/S0924-0136(02)01133-0 ↗
10. E. Bayraktar and D. Katundi, “Development of a new aluminium matrix composite reinforced with iron oxide (Fe3O4),” J. Achievements Mater. Manufac. Eng., 38, No. 1, 7–14 (2010).
11. M. Dixit and R. Srivastava, “The effect of copper granules on interfacial bonding and properties of the copper-graphite composite prepared by flake powder metallurgy,” Adv. Powder Technol., 30, No. 12, 3067–3078 (2019).10.1016/j.apt.2019.09.013 ↗
12. M. Dixit and R.K. Srivastava, “Effect of compaction pressure on microstructure, density and hardness of copper prepared by powder metallurgy route,” IOP Conf. Series: Mater. Sci. Eng., 377, 012209 (2018).10.1088/1757-899X/377/1/012209 ↗
13. N. Kumar, A. Bharti, and K.K. Saxena, “A re-analysis of effect of various process parameters on the mechanical properties of Mg based MMCs fabricated by powder metallurgy technique,” Mater.Today: Proceedings, 26, No. 2, 1953–1959 (2020).
14. N. Kumar, A. Bharti, and H. Tripathi, Investigation of Microstructural and Mechanical Properties of Magnesium Matrix Hybrid Composite, in: Advances in Mechanical Engineering, Springer, Singapore (2020), pp. 661–669.
15. D. Kumar, A. Bharti, S.M. Azam, N. Kumar, and H. Tripathi, Investigations of Mechanical Properties of Copper Matrix Hybrid Composite, in: Advances in Mechanical Engineering, Springer, Singapore (2020), pp. 671–676.
16. G.R. Cabriales, A.L. Sánchez, J.G. Tello, H.M. Prieto, E.G. Castañeda, I.E. Guel, C.G. Reyes, J.H. Rivera, J.C. Rivera, M.M. Orozco, and R.M. Sánchez, “Synthesis and characterization of Al–Cu–Mg system reinforced with tungsten carbide through powder metallurgy,” Materials Today Communications, 22, No. 1, 100758 (2019).10.1016/j.mtcomm.2019.100758 ↗
17. B. Wan, W. Chen, T. Lu, F. Liu, Z. Jiang, and M. Mao, “Review of solid state recycling of aluminium chips,” Resour. Conserv. Recycl., 125, No. 1, 37–47 (2017).10.1016/j.resconrec.2017.06.004 ↗
18. J. Fogagnolo, E.R. Navas, M.A. Simón, and M.A. Martinez, “Recycling of aluminium alloy and aluminium matrix composite chips by pressing and hot extrusion,” J. Mater. Proc. Technol., 143–144, No. 1, 792–795 (2003).10.1016/S0924-0136(03)00380-7 ↗
19. L. Dragošek, R. Kociško, A. Kovácová, R. Bidulský, and M. Škrobian, “The compacting process of the EN AW 6060 alloy,” Acta Polytechn., 55, No. 5, 301–305 (2015).10.14311/AP.2015.55.0301 ↗
20. Z. Sherafat, M.H. Paydar, and R. Ebrahimi, “Fabrication of Al7075/Al, two phase material, by recycling Al7075 alloy chips using powder metallurgy route,” J. Alloys Compd., 487, No. 1–2, 395–399 (2009).10.1016/j.jallcom.2009.07.146 ↗
21. A. Canakci and T. Varol, “Microstructure and properties of AA7075/Al–SiC composites fabricated using powder metallurgy and hot pressing,” Powder Technol., 268, No. 1, 72–79 (2014).10.1016/j.powtec.2014.08.016 ↗
22. Y.F. Fuziana, A.R.M. Warikh, M.A. Lajis, M.A. Azam, and N.S. Muhammad, “Recycling aluminium (Al 6061) chip through powder metallurgy route,” Mater. Research Innovat., 18, No. S6, 354–358 (2014).
23. X. Yao, Z. Zhang, Y.F. Zheng, C. Kong, M.Z. Quadir, J.M. Liang, Y.H. Chen, P. Munroe, and D.L. Zhang, “Effects of SiC nanoparticle content on the microstructure and tensile mechanical properties of ultrafine grained AA6063-SiCnp nanocomposites fabricated by powder metallurgy,” J. Mater. Sci. Technol., 33, No. 9, 1023–1030 (2016).10.1016/j.jmst.2016.09.022 ↗
24. I. Duarte, E. Venturaa, S. Olherob, J.M.F. Ferreira, “A new class of closed-cell aluminium foams reinforced with carbon nanotubes,” Ciência Tecnol. Mater., 28, 5–8 (2016).10.1016/j.ctmat.2016.06.003 ↗
25. C.A. Vogiatzis and S.M. Skolianos, “On the sintering mechanisms and microstructure of aluminium–ceramic cenospheres syntactic foams produced by powder metallurgy route,” Composites: Part A., 82, No. 1, 8–19 (2015).
26. S. Singh and N. Bhatnagar, “A survey of fabrication and application of metallic foams (1925–2017),” J. Porous Mater., 25, 537–554 (2018).10.1007/s10934-017-0467-1 ↗
27. M.R. Moradia, A. Moloodib, and A. Habibolahzadeh, “Fabrication of nano-composite Al–B4C foam via powder metallurgy-space holder technique,” Proc. Mater. Sci., 11, 553–559 (2015).10.1016/j.mspro.2015.11.059 ↗
28. R. Surace, L.A.C.D. Filippis, A.D. Ludovico, and G. Boghetich, “Experimental analysis of the effect of control factors on aluminium foam produced by powder metallurgy,” Proc. Estonian Acad. Sci. Eng., 13, No. 2, 156–167 (2007).
29. R. Surace, L.A.C.D. Filippis, A.D. Ludovico, and G. Boghetich, “Influence of processing parameters on aluminium foam produced by space holder technique,” Mater. Design., 30, No. 6, 1878–1885 (2009).10.1016/j.matdes.2008.09.027 ↗
30. P.M.P. Flores, G.M. Suarez, and R.A.L. Drew, “Effect of TiH2 particle size distribution on aluminium foaming using the powder metallurgy method,” J. Mater. Sci., 47, 455–464 (2012).10.1007/s10853-011-5820-1 ↗
31. A. Kennedy, “The effect of TiH2 heat treatment on gas release and foaming in Al–TiH2 preforms,” Scr. Mater., 47, No. 11, 763–767 (2002).10.1016/S1359-6462(02)00281-6 ↗
32. A.R. Kennedy, “Effect of compaction density on foamability of Al–TiH2 powder compacts,” Powder Metall., 45, No. 1, 75–79 (2013).10.1179/003258902225001579 ↗
33. P.P. Flores and L. Drew, “Production of aluminium foams with Ni-coated TiH2 powder,” Adv. Eng. Mater., 10, No. 9, 830–834 (2008).10.1002/adem.200800135 ↗