journal article·2007-06

Validation of an alkali reaction, borate fusion, X-ray fluorescence method for silicon metal

John R. Sieber, Elizabeth A. Mackey, Anthony F. Marlow, Rick Paul, Ryan Martin

Powder Diffraction· Volume 22· Issue 2
Publisher page

Abstract

The value assignment of candidate Standard Reference Material (SRM®) 57b Silicon Metal provided an opportunity to develop an alkali reaction procedure as a precursor to borate fusion for the preparation of test specimens from the metal powder for X-ray fluorescence spectrometry (XRF). Suggested for this purpose by Blanchette in a 2002 Advances in X-ray Analysis article [45, 415–420 (2002)], the alkali reaction uses LiOH∙H 2 O to convert Si to Li 2 SiO 3 . Lithium silicate is fused with lithium borate flux without damage to platinum ware. Once specimens are fused and cast as beads, calibration standards are prepared to closely match the compositions of the specimens, allowing a linear calibration for each analyte. The XRF method yields results that are directly traceable to the mole through NIST SRM spectrometric solutions. The method was validated in two ways. First, the reaction was used on older SRMs for Si metal: SRM 57 and SRM 57a. Second, XRF results for candidate SRM 57b were compared to results obtained using prompt gamma-ray activation analysis (PGAA) and inductively coupled plasma optical emission spectrometry (ICPOES). Bias tests show the XRF results are accurate for the elements Al, S, Ca, Ti, Cr, Mn, Ni, Cu, and Zr. Levels of S, Ca, Cr, and Cu in candidate SRM 57b are near the limits of quantification of the borate fusion method. Iron results may be subject to a low bias. Phosphorus is not quantitatively retained during the alkali reaction and borate fusion. These elements, plus B, which cannot be determined after borate fusion, are listed in manufacturing specifications for Si metal.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: X-ray Spectroscopy and Fluorescence Analysis · Nuclear Physics and Applications · X-ray Diffraction in Crystallography

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. 10.1021/ac00229a03610.1021/ac00229a036 ↗
2. Mineral Information Institute (2006). “Silicon or Silica” (Mineral Information Institute, Golden, CO), 〈http://www.mii.org/Minerals/photosil.html〉.
3. A quick and reliable fusion method for silicon and ferrosilicon
4. ISO (1993). Guide to the Expression of Uncertainty in Measurement (International Organization for Standardization, Geneva).
5. Becker D. , Christensen R. , Currie L. , Diamondstone B. , Eberhardt K. , Gills T. , Hertz H. , Klouda G. , Moody J. , Parris R. , Schaffer R. , Steel E. , Taylor J. , Watters R. , and Zeisler R. (1992). Use of Standard Reference Materials for Decisions on Performance of Analytical Chemical Methods and Laboratories, NIST Spec. Pub. 829. (U.S. Government Printing Office, Washington, DC).
6. ISO (2006). ISO Guide 35:2006, Reference Materials—General and Statistical Principles for Certification (International Organization for Standardization, Geneva).
7. Government of Western Australia. (2005). Silicon Products Investment Opportunity Report (Department of Industry and Resources, Government of Western Australia, Perth), 〈http://www.doir.wa.gov.au/documents/investment/siliconJan06.pdf〉.
8. May W. E. , Parris R. M. , Beck II C. M. , Fassett J. D. , Greenberg R. R. , Guenther F. R. , Kramer G. W. , Wise S. A. , Gills T. E. , Colbert J. C. , Gettings R. J. , and MacDonald B. S. (2000). Definitions of Terms and Modes Used at NIST for Value-Assignment of Reference Materials for Chemical Measurements, NIST Spec. Pub. 260-136. (U. S. Government Printing Office, Washington, DC), p. 16.
9. 10.1021/ac034201810.1021/ac0342018 ↗
10. Taylor B. N. and Kuyatt C. E. (1994). Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results, NIST Technical Note 1297 (U. S. Government Printing Office, Washington, DC).
11. Accurate X-ray fluorescence analysis without internal standard
12. 10.1002/xrs.78910.1002/xrs.789 ↗
13. 10.1023/A:100670580385710.1023/A:1006705803857 ↗
14. 10.1016/S0169-7439(97)00009-910.1016/S0169-7439(97)00009-9 ↗
15. 10.1016/S0008-8846(02)00896-710.1016/S0008-8846(02)00896-7 ↗
16. 10.1007/s00216005070210.1007/s002160050702 ↗
17. Claisse · 2004
18. Matrix-independent XRF methods for certification of standard reference materials
19. NIST (2006a). Certificate of Analysis, Standard Reference Material 57, Refined Silicon (National Institute of Standards and Technology, Gaithersburg, MD), 〈http://ts.nist.gov/MeasurementServices/ReferenceMaterials/ARCHIVED/CERTIFICATES/57pdf〉.
20. NIST (2006b). Certificate of Analysis, Standard Reference Material 57a, Silicon Metal (National Institute of Standards and Technology, Gaithersburg, MD), 〈https://srmors.nist.gov/certificates/view_cert2gif.cfm?certificate=57A〉.
21. Elkem ASA (2002). “Product data sheet: Silicon 99 Refined,” Rev. Sept. 2002. Elkem ASA, Oslo, Norway.
22. ASTM International (2000). ASTM A 922–93 (Reapproved 2000), Standard Specification for Silicon Metal, Historical Standard (ASTM International, West Conshohocken, PA).