Dual additive strategy to regulate the phase separation of bulk heterojunction layer for efficiency enhancement in non-fullerene organic solar cells
Source abstract
Abstract
The phase separation of bulk heterojunction (BHJ) layer is critical for the exciton dissociation, charge transport and recombination in non-fullerene organic solar cells (OSCs), therefore accurately regulating the BHJ phase separation must be one of the significant strategies to enhance the performance of non-fullerene OSCs. In this paper, dual additive strategy (1,8-diiodooctane (DIO) and methanol (MeOH)) is proposed to regulate the phase separation of PBDB-TF:IT-4F layer. Experimental studies reveal that this dual additive strategy could decrease domain size which is beneficial to exciton dissociation. Moreover, the extraction of low boiling point MeOH from the BHJ film can bring some IT-4F dissolved in DIO:MeOH:CB toward to the BHJ surface and thus improve the vertical distribution and form an efficient bi-continuous charge transport routes in BHJ layer for balancing charge transport in OSCs. Consequently, with dual additive DIO and MeOH, the short circuit current density raises from 19.79 to 21.13 mA cm −2 , fill factor enhances from 67.73% to 70.86%, and the power conversion efficiency increases from 11.26% to 12.72% with ∼13% improvement. Notably, this dual additive strategy is free of complicated treatment which is suitable for practical application.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Perovskite Materials and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (39)
Show source-provided references
1. Low-Bandgap non-fullerene acceptors enabling high-performance organic solar cells10.1021/acsenergylett.0c02384 ↗
2. Interlayers for non-fullerene based polymer solar cells: distinctive features and challenges10.1039/D0EE02503H ↗
3. Single-junction organic photovoltaic cell with 19% efficiency10.1002/adma.202102420 ↗
4. Effect of solvent-induced phase separation on performance of carboxylic indoline-based small-molecule organic solar cells10.1016/j.dyepig.2017.12.064 ↗
5. Concurrent improvement in JSC and VOC in high-efficiency ternary organic solar cells enabled by a red-absorbing small-molecule acceptor with a high LUMO level10.1039/D0EE00662A ↗
6. Fibril network strategy enables high‐performance semitransparent organic solar cells10.1002/adfm.202002181 ↗
7. Influence of 3D morphology on the performance of all-polymer solar cells processed using environmentally benign nonhalogenated solvents10.1016/j.nanoen.2020.105106 ↗
8. Non-halogenated additive engineering for morphology optimization in environmental-friendly solvent processed non-fullerene organic solar cells10.1016/j.orgel.2020.105893 ↗
9. Simultaneous improvement of three parameters using a binary processing solvent system approach in as-cast non-fullerene solar cells10.1039/C9TA10887D ↗
10. Highly efficient non-fullerene organic solar cells enabled by a delayed processing method using a non-halogenated solvent10.1039/D0EE02034F ↗
11. A high-efficiency organic solar cell enabled by the strong intramolecular electron push-pull effect of the nonfullerene acceptor10.1002/adma.201707170 ↗
12. A highly efficient non-fullerene organic solar cell with a fill factor over 0.80 enabled by a fine-tuned hole-transporting layer10.1002/adma.201801801 ↗
13. Control and characterization of organic solar cell morphology through variable-pressure solvent vapor annealing
14. Morphology and efficiency enhancements of PTB7-Th:ITIC nonfullerene organic solar cells processed via solvent vapor annealing10.1016/j.jechem.2018.12.015 ↗
15. Subtle morphology control with binary additives for high-efficiency non-fullerene acceptor organic solar cells10.1021/acsami.0c05331 ↗
16. The influence of the blend ratio, solvent additive, and post-production treatment on the polymer dynamics in PTB7:PCBM blend films10.1021/acs.macromol.1c00313 ↗
17. High-efficiency organic solar cells with low voltage loss induced by solvent additive strategy10.1016/j.matt.2021.06.010 ↗
18. High performance organic solar cells enabled by an iodinated additive10.1016/j.orgel.2021.106161 ↗
19. Fullerene as an additive for increasing the efficiency of organic solar cells to more than 17%10.1016/j.jcis.2021.05.033 ↗
20. A well-mixed phase formed by two compatible non-fullerene acceptors enables ternary organic solar cells with efficiency over 18.6%10.1002/adma.202101733 ↗
21. Incorporation of a classical visible non-fullerene acceptor into host binary blend enable ternary high-performance semitransparent polymer solar cells10.1016/j.cej.2021.132048 ↗
22. Realizing high-performance organic solar cells through precise control of HOMO driving force based on ternary alloy strategy10.1016/j.jechem.2021.05.053 ↗
23. Highly efficient organic solar cells with improved vertical donor-acceptor compositional gradient via an inverted off-center spinning method10.1002/adma.201504014 ↗
24. Simultaneously enhanced efficiency and stability of polymer solar cells by employing solvent additive and upside-down drying method10.1021/acsami.7b00510 ↗
25. Vertical stratification engineering for organic bulk-heterojunction devices10.1021/acsnano.8b00439 ↗
26. Control of vertical phase separation in high performance non-fullerene organic solar cell by introducing oscillating stratification preprocessing10.1007/s12274-020-3169-y ↗
27. Top-down approach for nanophase reconstruction in bulk heterojunction solar cells10.1002/adma.201402182 ↗
28. Universal formation of compositionally graded bulk heterojunction for efficiency enhancement in organic photovoltaics10.1002/adma.201305196 ↗
29. A simple method to adjust the morphology of gradient three-dimensional PTB7-Th:PC71BM polymer solar cells10.1039/C5NR00148J ↗
30. Facile method of solvent-flushing to building component distribution within photoactive layers for high-performance organic solar cells10.1021/acsami.0c07173 ↗
31. Non-toxic green food additive enables efficient polymer solar cells through adjusting the phase composition distribution and boosting charge transport10.1039/C9TC06571G ↗
32. A facile strategy for third-component selection in non-fullerene acceptor-based ternary organic solar cells10.1039/D1EE01864G ↗
33. High mobility acceptor as third component enabling high-performance large area and thick active layer ternary solar cells10.1016/j.cej.2021.129539 ↗
34. Single-junction organic photovoltaic cells with approaching 18% efficiency10.1002/adma.201908205 ↗
35. Approaching 18% efficiency of ternary organic photovoltaics with wide bandgap polymer donor and well compatible Y6 : Y6-1O as acceptor10.1093/nsr/nwaa305 ↗
36. A two-step strategy to clarify the roles of a solution processed PFN interfacial layer in highly efficient polymer solar cells10.1039/C5TA05117G ↗
37. TCNQ as a volatilizable morphology modulator enables enhanced performance in non-fullerene organic solar cells10.1039/C9TC04892H ↗
38. Revealing morphology evolution in highly efficient bulk heterojunction and pseudo‐planar heterojunction solar cells by additives treatment10.1002/aenm.202003390 ↗
39. Efficient fullerene-free organic solar cells using a coumarin-based wide-band-gap donor material10.1021/acsami.0c12147 ↗