Improved efficiency and stability of inverted polymer solar cells with a solution-processed BPhen interlayer and polystyrene beads
Source abstract
Abstract
Abstract We demonstrate improved power conversion efficiency (PCE) and strongly enhanced stability of inverted organic solar cells (OSCs) with Cs halides by solution casting BPhen (4,7-di(phenyl)-1,10-phenanthroline) on the halide layer and ∼100 nm polystyrene beads (PSB) on the blank side of the OSC’s substrate. The PCE of ITO/CsCl/P3HT:PCBM/MoO3/Al (where P3HT is poly 3-hexylthiophene and PCBM is [6,6]-phenyl-C60-butyric acid methyl ester) improves by up to 46%, from 2.5% to ∼3.7%, by adding a solution-processed BPhen layer between the CsCl and the active layer. For such cells with CsI (PCE ∼3.3–3.4%) the increase was only 6–9%, to 3.5–3.7%. The PCE of cells devoid of the halides but with BPhen was ∼3.3%. The cells were optimized by varying the BPhen concentration in a chlorobenzene solution. The results are consistent with reduced charge recombination at the ITO interface in the presence of the hole blocking BPhen interlayer. The use of hole blocking BCP (2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline), as a substitute for BPhen, also showed an enhancement (though lower due to its lower electron mobility), verifying the effect of these materials as hole blocking interlayers. Interestingly, the stability of such non-encapsulated devices with CsCl/BPhen or CsI/BPhen improved significantly. For example, the PCE of unencapsulated cells with CsCl/BPhen kept in the dark under ambient conditions dropped by less than 2% after more than 3 weeks; the PCE of similar cells devoid of the BPhen layer dropped by ∼60% during the same period. The PCE of the cell with CsCl/BPhen dropped by ∼16% after 2 months. High humidity, as expected, resulted in faster deterioration in cell performance. The PCE, however, was restored to within ∼10% of the original value for 2 week old cells by solution–application of a PSB layer on the blank side of the cell’s glass substrate. These beads direct and scatter the light to enhance absorption in the active layer. The results demonstrate that a simple approach such as casting a film of ∼100 nm diameter PSB from an aqueous suspension on the blank side of the OSC substrate can improve long-term performance, and that spin coating BPhen is a low-cost and easy approach to reduce charge recombination at the cathode in inverted structures for increased PCE and stability.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Perovskite Materials and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. Tandem polymer solar cells featuring a spectrally matched low-bandgap polymer10.1038/nphoton.2011.356 ↗
2. Polymer solar cells with enhanced open-circuit voltage and efficiency10.1038/nphoton.2009.192 ↗
3. For the bright future—bulk heterojunction polymer solar cells with power conversion efficiency of 7.4%10.1002/adma.200903528 ↗
4. Bulk heterojunction olar cells using thieno[3,4-c]pyrrole-4,6-dione and dithieno[3,2-b:2′,3′-d]silole copolymer with a power conversion efficiency of 7.3%10.1021/ja200314m ↗
5. Solar cell efficiency tables (version 37)10.1002/pip.1088 ↗
6. Stability and photodegradation mechanisms of conjugated polymer/fullerene plastic solar cells10.1016/S0927-0248(99)00094-X ↗
7. Patterns of efficiency and degradation of composite polymer solar cells10.1016/j.solmat.2004.02.028 ↗
8. Influence of thermal ageing on the stability of polymer bulk heterojunction solar cells10.1016/j.solmat.2006.10.008 ↗
9. Flexible organic P3HT:PCBM bulk-heterojunction modules with more than 1 year outdoor lifetime10.1016/j.solmat.2008.01.004 ↗
10. Upscaling of polymer solar cell fabrication using full roll-to-roll processing10.1039/b9nr00430k ↗
11. High efficiency polymer solar cells with long operating lifetimes10.1002/aenm.201100138 ↗
12. Influence of the exciton blocking layer on the stability of layered organic solar cells10.1016/j.jpcs.2010.11.006 ↗
13. Improvement of both efficiency and working lifetime in organic photovoltaic devices by using bathophenanthroline/tin(IV) phthalocyanine dichloride as bilayer exciton blocking layers10.1063/1.4729146 ↗
14. Efficient photon harvesting at high optical intensities in ultrathin organic double-heterostructure photovoltaic diodes10.1063/1.126433 ↗
15. Efficient photon harvesting at high optical intensities in ultrathin organic double-heterostructure photovoltaic diodes10.1063/1.1384001 ↗
16. Charge separation at molecular donor–acceptor interfaces: correlation between morphology and solar cell performance10.1109/JSTQE.2010.2048096 ↗
17. Influence of molecular architecture and intermixing on the photovoltaic, morphological and spectroscopic properties of CuPc–C60 heterojunctions10.1016/j.solmat.2004.02.027 ↗
18. Small molecular weight organic thin-film photodetectors and solar cells10.1063/1.1534621 ↗
19. High electron mobility in bathophenanthroline10.1063/1.125701 ↗
20. Degradation of organic solar cells due to air exposure10.1016/j.solmat.2006.06.041 ↗
21. Stability/degradation of polymer solar cells10.1016/j.solmat.2008.01.005 ↗
22. Lifetimes of organic photovoltaics: combining chemical and physical characterisation techniques to study degradation mechanisms10.1016/j.solmat.2006.04.009 ↗
23. Analysis of the failure mechanism for a stable organic photovoltaic during 10,000h of testing10.1002/pip.794 ↗
24. Organic double-heterostructure photovoltaic cells employing thick tris(acetylacetonato)ruthenium(III) exciton-blocking layers10.1002/adma.200500816 ↗
25. Gebeyehu · Thin Solid Films · 2004 · 29 · 451
26. Application of metal-doped organic layer both as exciton blocker and optical spacer for organic photovoltaic devices10.1063/1.2362974 ↗
27. Efficient inverted polymer solar cells incorporating doped organic electron transporting layer10.1016/j.orgel.2012.01.009 ↗
28. Charge carriers and charge-transfer reactions in OLED devices studied by electron paramagnetic resonance
29. Inverted polymer solar cells with a solution-processed cesium halide interlayer10.1016/j.orgel.2012.10.020 ↗
30. Soft holographic interference lithography microlens for enhanced organic light emitting diode light extraction10.1364/OE.19.00A786 ↗
31. A universal optical approach to enhancing efficiency of organic-based photovoltaic devices10.1039/c2ee21254d ↗
32. Polydimethylsiloxane as a macromolecular additive for enhanced performance of molecular bulk heterojunction organic solar cells10.1021/am2000328 ↗
33. V. Dalal, M. Leonard, J. Booker, A. Vaseashta, Quantum efficiency of amorphous alloy solar cells, in: Proc. 18th IEEE Photovolt Spec. Conf., 1985, pp. 837.
34. Air-plasma-treated alkali fluoride layers for improved hole extraction in copper phthalocyanine/C70-based solar cells10.1117/1.JPE.2.021006 ↗
35. Electronic and chemical properties of cathode structures using 4,7-diphenyl-1,10-phenanthroline doped with rubidium carbonate as electron injection layers10.1063/1.3143718 ↗
36. Dynamic turn-on behavior of organic light-emitting devices with different work function cathode metals under fast pulse excitation10.1063/1.1628835 ↗
37. Operational stability of electrophosphorescent devices containing p and n doped transport layers10.1063/1.1624473 ↗
38. Photoinduced degradation of polymer and polymer–fullerene active layers: experiment and theory10.1002/adfm.201001079 ↗