journal article·2015-11

Morphology construction of vertical phase separation for large-area polymer solar cells

Fan Wu, Feng Ye, Zhaobin Chen, Yi Cui, Dalei Yang, Zidong Li, Xiaoli Zhao, Xiaoniu Yang

Publisher page

Abstract

Although the power conversion efficiency (pce) of small-area polymer solar cells (pscs) has now surpassed 10% upon various optimizations, it is still a challenge to improve the performance of large-area device partially due to the problems encountered in film morphology optimization and incompatibility of using these optimizations for size scale-up. herein, we reported a method to effectively improve the morphology of photoactive layer and thus device efficiency under ambient atmosphere by using spray coating technique. it was found that by finely adjusting the parameters of the instrument, and the properties of the "electronic ink'', the dynamics of solvent evaporation after film deposition could be controlled. by resorting to a few techniques for morphology characterization, it confirmed that the resulting blend film showed desirable vertical phase separation where polymer enriched near the anode and pcbm adjacent to the cathode. the graded composition is beneficial for the efficient charge transportation as well as eventual charge collection. by using pbdt-tfq/pc71bm composite as an example, the exceptional high pces of 4.6% and 4.1% were achieved for the devices with the size of 1.0 and 10.2 cm(2), respectively. in comparison to conventional device fabrication process, this method is not only simple without additional treatment steps, but also dramatically increases the device efficiency, which opens a new way for fabricating highly efficient large-area pscs. (c) 2015 elsevier b.v. all rights reserved.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Organic Electronics and Photovoltaics · Conducting polymers and applications · Thin-Film Transistor Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (60)

Show source-provided references
1. Polymer solar cells10.1038/nphoton.2012.11 ↗
2. Fabrication and processing of polymer solar cells: a review of printing and coating techniques10.1016/j.solmat.2008.10.004 ↗
3. Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure10.1038/nphoton.2012.190 ↗
4. Controlling the dominant length scale of liquid–liquid phase separation in spin-coated organic semiconductor films10.1002/adfm.201403392 ↗
5. Achieving high efficiency of PTB7-based polymer solar cells via integrated optimization of both anode and cathode interlayers10.1002/aenm.201301771 ↗
6. Morphology evolution via self-organization and lateral and vertical diffusion in polymer: fullerene solar cell blends10.1038/nmat2102 ↗
7. Nanoscale morphology of high-performance polymer solar cells10.1021/nl048120i ↗
8. High-efficiency solution processable polymer photovoltaic cells by self-organization of polymer blends10.1038/nmat1500 ↗
9. Solution-processed small-molecule solar cells with 6.7% efficiency10.1038/nmat3160 ↗
10. Efficiency enhancement in low-bandgap polymer solar cells by processing with alkane dithiols10.1038/nmat1928 ↗
11. Highly efficient 2D-conjugated benzodithiophene-based photovoltaic polymer with linear alkylthio side chain10.1021/cm501513n ↗
12. High-molecular-weight regular alternating diketopyrrolopyrrole-based terpolymers for efficient organic solar cells10.1002/anie.201302319 ↗
13. Pyridalthiadiazole-based narrow band gap chromophores10.1021/ja209331y ↗
14. A high efficiency solution processed polymer inverted triple-junction solar cell exhibiting a power conversion efficiency of 11.83%10.1039/C4EE03048F ↗
15. A polymer tandem solar cell with 10.6% power conversion efficiency10.1038/ncomms2411 ↗
16. For the bright future-bulk heterojunction polymer solar cells with power conversion efficiency of 7.4%10.1002/adma.200903528 ↗
17. Universal formation of compositionally graded bulk heterojunction for efficiency enhancement in organic photovoltaics10.1002/adma.201305196 ↗
18. Enhanced photovoltaic performance by modulating surface composition in bulk heterojunction polymer solar cells based on PBDTTT-C-T/PC71BM10.1002/adma.201400411 ↗
19. Fabricating high performance, donor–acceptor copolymer solar cells by spray-coating in air10.1002/aenm.201200713 ↗
20. Polymer solar cells with enhanced fill factors10.1038/nphoton.2013.207 ↗
21. Improving performance of polymer solar cells based on PSBTBT/PC71BM via controlled solvent vapor annealing10.1016/j.orgel.2013.04.022 ↗
22. Solvent-soaking treatment induced morphology evolution in P3HT/PCBM composite films10.1039/c1jm10148j ↗
23. Remove the residual additives toward enhanced efficiency with higher reproducibility in polymer solar cells10.1021/jp404395q ↗
24. High photovoltaic performance of inkjet printed polymer: Fullerene blends10.1002/adma.200700911 ↗
25. Roll-to-roll inkjet printing and photonic sintering of electrodes for ITO free polymer solar cell modules and facile product integration10.1002/aenm.201200520 ↗
26. High precision processing of flexible P3HT/PCBM modules with geometric fill factor over 95%10.1016/j.orgel.2014.06.006 ↗
27. Large area slot-die coated organic solar cells on flexible substrates with non-halogenated solution formulations10.1016/j.solmat.2014.06.017 ↗
28. Fabrication of bulk heterojunction plastic solar cells by screen printing10.1063/1.1413501 ↗
29. It is all in the pattern-high-efficiency power extraction from polymer solar cells through high-voltage serial connection10.1002/ente.201200055 ↗
30. Semitransparent OPV modules pass environmental chamber test requirements10.1016/j.solmat.2012.09.031 ↗
31. Performance analysis of printed bulk heterojunction solar cells10.1002/adfm.200500581 ↗
32. High efficient plastic solar cells fabricated with a high-throughput gravure printing method10.1016/j.solmat.2010.05.027 ↗
33. Gravure printed flexible organic photovoltaic modules10.1016/j.solmat.2010.12.020 ↗
34. Organic photovoltaic modules fabricated by an industrial gravure printing proofer10.1016/j.solmat.2012.10.018 ↗
35. Ultrasonic spray deposition for production of organic solar cells10.1016/j.solmat.2008.10.026 ↗
36. Fabrication of organic bulk heterojunction solar cells by a spray deposition method for low-cost power generation10.1063/1.2772766 ↗
37. Ultrasonic spray coating of 6.5% efficient diketopyrrolopyrrole-based organic photovoltaics10.1109/JPHOTOV.2014.2352153 ↗
38. Concurrently pumped ultrasonic spray coating for donor: acceptor and thickness optimization of organic solar cells10.1016/j.orgel.2013.01.023 ↗
39. Surface treatment patterning of organic photovoltaic films for low-cost modules10.1016/j.orgel.2012.11.018 ↗
40. Process optimization of ultrasonic spray coating of polymer films10.1021/la4010246 ↗
41. Morphological characterization of spray-coated PCBM thin films10.1380/ejssnt.2012.538 ↗
42. High-performance organic solar cells with spray-coated hole-transport and active layers10.1002/adfm.201001562 ↗
43. Ultrasonically sprayed and inkjet printed thin film electrodes for organic solar cells10.1016/j.tsf.2008.10.124 ↗
44. Efficient planar heterojunction mixed-halide perovskite solar cells deposited via spray-deposition10.1039/C4EE01546K ↗
45. Spray deposition of high quality CuInSe2 and CdTe films
46. Flexible polymer solar cell modules with patterned vanadium suboxide layers deposited by an electro-spray printing method10.1016/j.solmat.2014.07.053 ↗
47. Fabrication of fully-spray-processed organic photovoltaic modules by using an automated process in air10.1002/ente.201300107 ↗
48. Organic photovoltaic devices incorporating a molybdenum oxide hole-extraction layer deposited by spray-coating from an ammonium molybdate tetrahydrate precursor10.1016/j.orgel.2013.12.028 ↗
49. Topographical and morphological aspects of spray coated organic photovoltaics10.1016/j.orgel.2009.02.010 ↗
50. Quantitative imaging of shunts in organic photovoltaic modules using lock-in thermography10.1016/j.solmat.2014.01.030 ↗
51. Effect of solvent on large-area polymer-fullerene solar cells fabricated by a slot-die coating method10.1016/j.solmat.2014.03.042 ↗
52. Scalable, ambient atmosphere roll-to-roll manufacture of encapsulated large area, flexible organic tandem solar cell modules10.1039/C4EE01223B ↗
53. Spray-coated organic solar cells with large-area of 12.25cm210.1016/j.solmat.2010.10.033 ↗
54. Preparation of large area inverted polymer solar cells by spray coating technique10.3724/SP.J.1095.2012.20433 ↗
55. Prominent short-circuit currents of fluorinated quinoxaline-based copolymer solar cells with a power conversion efficiency of 8.0%10.1021/cm302861s ↗
56. Spray coated high-conductivity PEDOT:PSS transparent electrodes for stretchable and mechanically-robust organic solar cells10.1016/j.solmat.2012.09.005 ↗
57. Low-voltage organic transistors based on solution processed semiconductors and self-assembled monolayer gate dielectrics10.1063/1.2954015 ↗
58. Effects of additives on the morphology of solution phase aggregates formed by active layer components of high-efficiency organic solar cells10.1021/ja2085564 ↗
59. Effects of solvent mixtures on the nanoscale phase separation in polymer solar cells10.1002/adfm.200701459 ↗
60. Area dependent efficiency of organic solar cells10.1063/1.2998540 ↗